Question about 1994 Ford Aerostar Extended

Open Question

Tune up procedure for series 60 12.7 litre Detroit diesel engine

I am about to set the valve clearances, Jacobs Brake and injector settings and would like to know where the measurements for the injector heights are taken and at what point of the crank shaft positioning each one is done?

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
simontricket
  • 235 Answers

SOURCE: what is the tappet clearance of isuzu bighorn 3.1

Its 0.016 thou - cold setting .

Posted on Jul 07, 2009

Ad
  • 56 Answers

SOURCE: ford F250 6.0 litre turbo diesel won't start.

check the fuel cut-off switch under the glove box.

Posted on Jul 21, 2009

co7196
  • 3433 Answers

SOURCE: got a 1978 detroit diesel inline six and i need

What state are you in?

Posted on Nov 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Toyota Hilux 2.8 diesel 3l engine injector pump has great pressure on only 3 cylinders but number 4 is lacking pressure enough to make it miss , what can corse this problem


You didn't say but presumably the engine uses a DPA type or distributor type injection pump.

In this case the injector line pressure is governed by the condition and setting of each injector. If the break-off pressure of an injector is set to 80 atmospheres that pump element will produce a pressure of 80 atmospheres.

If one injector becomes "soft" and worn so the break-off pressure has fallen to 20 atmospheres for instance, or if the injector sticks open, the pressure generated by the pump will be either 20 atmospheres or virtually nothing.

When a conventional diesel engine develops a misfire, best practice is to ensure valve clearances and suchlike are in order, the compression pressure is good and then independently test the injector (and heater plug).

If everything is in order the pump should be removed for testing, repair and recalibration.

Jun 07, 2017 | Toyota Cars & Trucks

1 Answer

What is the clearance of inlet and outlet valve for mitsubishi 4DR5 engine.


When I set clearances, I like to do them while the engine is cool. I set the clearance for the diesels at 0.13mm for the intake and around 0.18mm on exhaust. Depends on engine wear. If the engine has high mileage, you may want to go less (0.001 to 0.002mm) on clearances.

Jun 14, 2016 | Mitsubishi Cars & Trucks

1 Answer

I OWN APEUGOT307 1.6 HDI.REPLACED HEAD. ENGINE TURNS BUT WILL NOT START.NEED TO KNOW WHAT THE PROBLEM CAN BE.


Did the head come with camshaft pre fitted? Have the valve to camshaft clearance been set. is the valve timing correct? is the injector pump timing correct. have the fuel filters been changed and all the air bled out of the system? do a compression test to check for worn piston rings or damage.

Sep 17, 2014 | Cars & Trucks

1 Answer

Need torque settings for mazda xa 3.0l diesel 4 cyl


con rod bolt tension is 55-60ft/lbs
crank shaft main bearings is 80-85 ft/lbs
fly wheel bolts95-100 ft/lbs
crank shaft pulley nut 94-123 ft/lb
head studs tension 80-95 ft/lbs working in a spiral direction from no 1 stud directly in the centre of the head. Pull down in 10ft/lb increment starting at 20 ft/lbs
valve clearance is .010" both valves cold but after warming engine and re-tensioning the head studs re set valves to .012 both valves
injector retaining nuts tension12-17 ft/lbs

Dec 25, 2013 | Saab 9 Cars & Trucks

1 Answer

Valve setting


Personally, the valve clearance (if nobody's been messing with it) would be last on my list of suspected causes.. Knowing diesel engines like I do, my very first suspect would be a dirty fuel filter.

Dec 03, 2013 | Cars & Trucks

1 Answer

Detroit diesel injector installation


thoroughly clean area around injectors,and then blow with compressed air so no bits will fall in the holes when injectors removed.loosen main injector pipe nut,remove return fuel line,dont lose copper washers,put special fuel bolts back in top of injector firm[by hand] undo holding down bolts evenly,undo fully injector pipe nut,.gently pry injector loose,and remove,making sure sealing washer at bottom also comes out..while I dont specifically know this particular engine,this guide applies to most diesel motors.I have rebuilt a 6v72 detroit motor,yrs ago.Assembly is reversal.may need to crank over to bleed diesel at injector,always use new sealing washers.

Jul 01, 2010 | 1990 Mercedes-Benz 300 Diesel

1 Answer

Bmw 3 litre diesel engine miss fire. Cylinder 5 not running? injector or valve?


Bude to injector,kdy┬× "no fire" tak u diesel motoru = "no dieselfuel"

Apr 17, 2010 | 2003 BMW 7 Series

Not finding what you are looking for?
1994 Ford Aerostar Extended Logo

Related Topics:

1,739 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5613 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...