Question about 2006 Peugeot 604

1 Answer

My peugeot 406 lx y plate wont start checked the fuel line and petrol is running fine. i just had a new clutch fitted there is a 4 loop system on the spark plugs but cant find the the wire they connect to to check if it has taken a knock when the clutch was fitted any ideas

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Hi.you have a red button/switch under your hood,try to push this down.this switch is mountet to cut the engine if the car tilt´s over

Posted on Jul 18, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Peugeot 406 hdi faults


Cam belts are due every 120,000km on peugeots. You should be fine for quite a while.

Sep 07, 2014 | Peugeot 406 Cars & Trucks

2 Answers

My 406 1.8liter engine has a tendency to shot down when in idle and cold. after 5 miles it runs fine.


Sounds as though it may be the Throttle Position Sensor. TPS. It is on e the throttle body and sets the idle of the engine.

Nov 22, 2013 | 1999 Peugeot 406

1 Answer

Location of peugeot 406 fuel pump relay


Can I know where the fuel pump relay and fuse location. Peugeot 406 2.0 petrol 2000 model

Aug 30, 2011 | Peugeot Liberte Cars & Trucks

1 Answer

206 w reg fitted new clutch but now have no biting point so car will not pull away help


Hello, Who installed the clutch"? Were there a new pressure plate installed? Were there a new throw out bearing installed. Does this 1991 Peugeot 405 have hydraulic or mechanical clutch linkage?
There a couple of reason why the Peugeot wont move and engine is running and the transmission is in gear.

1.. Pressure plate is installed backwards.--Remove transmission and reinstall pressure plate in the correct orientation to the clutch. There is two ways to install it, but one way correctly.

2. Adjustment for the clutch linkage from the pedal in the driver compartment is adjusted to tight and not releasing the clutch to where the clutch pressure is on the pressure plate.



I hope this helps. GB....stewbison

Aug 24, 2011 | 1991 Peugeot 405

1 Answer

Have a Peugeot 406 1.8 petrol LX on a 52 plate. Smell of coolant in the cab, no visible leak, top radiator hose hot, both hoses to heater matrix hot, bottom radiator hose cold. Air con works fine.


it could be a slight leak from the heater matrix (check for damp in the passanger foot well) its self or the thermostat may be sticking this may cause the bottom hose to stay cold. you could try removing the thermostat and running it without it and then putting a rad weld in the coolant system to seal the matrix.


let me know if this helps


cheers big mike

Mar 31, 2011 | 2005 Peugeot 405

1 Answer

Peugeot 406 sri 2.2 hdi estate 2001 'X' plate antipollution fault light on also fuel additive warning fault on, HELP!


im affraid it will be a trip to the dealers the fuel additive tank is located in or next to the fuel tank and can only be refilled by the dealers it also on the othe hand be caused by putting poor quality fuel in (one of our customers used to have the same fault when filling up with diesel from bp) all we did was erase the error code and fill car up at another petrol station, the car has been fine since

Nov 28, 2009 | Peugeot 405 Cars & Trucks

1 Answer

PEUGEOT 406 LX DT 1998 2088 CC CLUTCH SLAVE CYLINDER


I understand these cars have a sealed clutch system. When they fail you replace the whole kit master,hydrolic pipe and slave (comes in one piece). Search on ebay maybe £45 or so.

Jul 21, 2008 | 2005 Peugeot 405

Not finding what you are looking for?
Cars & Trucks Logo

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

scj103

Level 2 Expert

81 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...