Question about 2003 Ford Focus

Open Question

I need timing marks 4 1976 ford pinto mpg, 4 cylinder engine

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
stormbrewin
  • 426 Answers

SOURCE: 1976 ford f100 pickup 2wd

The brake bias valve can cause your symptom.Are the outer part of the brake calipers able to slide in and out freely .Jack it up take a wheel off and get someone to push on the brake pedal while you check for correct movement.Lube the slides so it is easier for calipers to return.a chunck of 4x2 wood is useful if you find them too hard to move by hand

Posted on Oct 09, 2008

Ad
  • 193 Answers

SOURCE: Can't fine an arrow to line up timing marks.

Hi. The older style engines had a metal arrow on the front timing cover. The newer ones may have a small raised area on the timing cover. It might be best to spray the area down with a can of brake kleen and then wipe the area down with a rag.
Bill

Posted on Nov 24, 2008

  • 701 Answers

SOURCE: where can i find the timing marks on 1998 ford escort zx2 ?

Hello pamgolmon: My name is Roger and i will answer your question. The 2-0 dual cam engine is a interference engine. This means if the engine jumps time at the timing belt. It will bend the valves. As for the timing marks on the camshafts. Their are no marks to be located. To set the timing marks on this engine requires special tools. This makes it expensive for not only the do it yourself mechanic but also the repair shops also. If the valves were bent you must pull the head for the repairs also.
I know this is not the answer you were hoping for but it is the only answer to give. Please rate the quality of the answer as this way we know your answer was correct. Please just ask if you need further help. Thank You for using Fix Ya. Roger

Posted on Sep 09, 2009

  • 1 Answer

SOURCE: carb adjustments for a 1970's Ford Pinto 2.3 liter 2barrel engine

I have the Petronics electronic distributor kit for that motor ,jkjhenry@cox.net

Posted on Sep 15, 2009

  • 1 Answer

SOURCE: need timing chain marks for 2002 ford explorer 4.0 lit

just need to know what kind of tools to use?

Posted on Mar 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque spec for a 1978 Ford pinto differential pinion nut?


170 ft.lbs is the minimum; be aware that this differential uses a crush sleeve to set the backlash and the pinion torque is what crushes the crush sleeve. If you don't set the backlash correctly you can grind up your differential gears.
8 Inch Ford Rear End Torque Specifications eHow

Feb 02, 2015 | Ford Cars & Trucks

1 Answer

Engine Timing marks on a 4.0 ford ranger on a 2005


Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

Nov 02, 2011 | 2005 Ford Ranger

1 Answer

1977 ford pinto timming marks


Hope this helps. Please don't forget to rate....thanks!



c17hydro_169.gif

Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)


On 2000 cc engines, turn the crankshaft until the two round locating holes in the camshaft pulley are visible from the rear side of the pulley, looking forward from the left-side of the car. When these two holes are parallel to the ground, the timing pointer on the crankshaft pulley should point to TDC. If the drive belt is dislocated, the crankshaft damper will be retarded or advanced 19° per cog on the belt.

If the engine you are working on does not have the two locating holes on the rear side of the camshaft pulley, then you will have to remove the drive belt cover and observe that when the crankshaft timing marks are aligned to TDC of the compression stroke of the No. 1 cylinder, the distributor rotor is pointing to the index mark on the upper lip of the distributor housing which coincides with No. 1 spark plug tower, and the pointer on the camshaft pulley is aligned with the index mark on the cylinder head.

On 2300 cc engines, there is an access plug provided in the cam drive belt cover so that the camshaft timing can be checked without removing the drive belt cover. Remove the access plug, turn the crankshaft until the timing mark on the crankshaft damper indicates TDC, and observe that the timing mark on the camshaft drive sprocket is aligned with the pointer on the inner belt cover. Also, the rotor of the distributor must align with the No. 1 cylinder firing position.


CAUTION:

After any procedure requiring removal of the rocker arms on the 2300, each lash adjuster must be fully collapsed after assembly, then released. This must be done before the camshaft is turned.



Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)

Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)
c17hydro_170.gif

Checking 2000 cc overhead camshaft timing (© Ford Motor Co)

May 08, 2011 | Ford Mustang Cars & Trucks

1 Answer

Have a kit car with a ford 2.0 ltr pinto sohc,rev counter wiring


Most rev counters of this type wire the positive wire to the contact points on the distributer and the black (negative) to ground.

Apr 16, 2010 | 1978 Ford Granada

2 Answers

Carb adjustments for a 1970's Ford Pinto 2.3 liter 2barrel engine


I have the Petronics electronic distributor kit for that motor ,jkjhenry@cox.net

Sep 15, 2009 | 1983 Ford Escort Gt

2 Answers

How much oil fills an engine correctly for a 1978 ford pinto?


I've always known them to be five quarts with a new oil filter.

Jun 28, 2009 | 2001 Daewoo Lanos

1 Answer

My 1992 ford escort 1.9 engine timing belt broke help


if the belts bloke then you will need to remove the head and prob have to change the exhaust or intake values if bent but this really needs to been done by some body who no's what they are doing as they will need to be ground in ,, but the draw is that this can be very exspensive to have done.. some times we can be lucky like some of the old ford pinto engines belts snapped and didnt cause any damage but engines have less a clearance these days higher compression for more power

hope this has helped matdav69

Apr 05, 2009 | 1992 Ford Escort 4 Door

1 Answer

Ford capri 1993cc pinto engine settingsof cam hot and cold and timing


more than likely its the gear ratio check the gear ratio specially if its an automatic

Jun 28, 2008 | Ford Contour Cars & Trucks

Not finding what you are looking for?
2003 Ford Focus Logo

Related Topics:

235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5579 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...