Question about 1994 Buick LeSabre

1 Answer

EGR VALVE 380 LITER WHERE IS IT ON THE MOTOR 1994 LESABRE

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 17,970 Answers

For 1994 Buick Lesabre 3.8L SFI OHV 6cyl the EGR Valve is located under hood, center, rear engine area, mounted top rear driver side of engine.

There is a 4-wire connector on the top and it is mounted by two bolts on a flange. About 2" in diameter, 4" high...


Posted on May 26, 2010

  • ZJ Limited
    ZJ Limited May 26, 2010




    All 1994-98 vehicles are equipped with a linear EGR valve - 3.8L
    (VIN L) shown


    Hope help with this (remember rated this).

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the egr valve located on a 1994 Ranger 4.0L V6?


If your ranger has a egr valve it will be on the driver's side of the upper intake plenum (the top aluminum housing, very top of the motor) and about centered on the plenum.in 1994 I have seen Rangers with and without a egr valve. I believe it depends on if its California emissions or not.

Dec 31, 2010 | Ford Ranger Cars & Trucks

1 Answer

2000 buick lesabre engine code p1404


P1404 - Exhaust Gas Recirculation (EGR) Closed Position Performance The egr valve is stuck possibly due to carbon buildup. It may be possible to remove the egr valve and clean it with throttle body cleaner or induction cleaner.If the pintle can not be unstuck then the valve egr will probably need replaced.

Sep 21, 2010 | 2000 Buick LeSabre

2 Answers

Location of EGR sensor


the EGR valve in your Buick LeSabre. The EGR valve is located on the driver's side of the engine bay, near the brake fluid reservoir. Since all EGR valves look basically the same, hope this helps

Sep 19, 2010 | 1994 Buick LeSabre

1 Answer

P0406 code for 1994 buick lesabre


DTC P0406 Exhaust Gas Recirculation Sensor A Circuit High.

You in fact do, need to replace the EGR valve. P0406 is actually EGR position sensor high code. Which means the PCM recieved a egr position sensor signal greater than 4.89 volts. For some reason the the egr on the 05 minivan had a high failure rate.

The best way to get at the lower bolt after you remove the upper bolt and the two 8mm tube screws, pry the valve rearward. This allows you to get a socket on the lower bolt.

Hope helps (remember to rate and comment this).

Sep 19, 2010 | 1994 Buick LeSabre

2 Answers

Dies at Idle and decelration - won't start for 15


Hello. I bet your problem is one of these two things. 1: your timing is out. Making it run at such a low idle that it stalls itself out. 2: your truck is running too rich and flooding itself out. Just adjust theb timing a bit and lean the motor out a bit and you should be as good as new! Hope this helps!

Dec 08, 2009 | 1994 Chevrolet S-10 Blazer

2 Answers

1992 Buick LaSabre. Where is the EGR valve?


The EGR valve may have a protective cover on it:
7a909a9.gif

After removing the cover, the egr valve is beneath, you will need to remove retaining clips to remove the egr valve.

fdd5d51.gif

Sep 04, 2009 | 1992 Buick LeSabre

1 Answer

Have SES light on Scaned PCM egr out of range on


First you need to remove the egr and clen the carbon out the pintle gets clogged and restrics the flow and in turn throws a code as all the checks are made by the pcm"drive cycles".

Jul 26, 2009 | 1994 Buick LeSabre

1 Answer

Egr malfunctioning


this engine is plagued with egr issues! the 4.3 liter engine is suspect to carbon build upo inside the intake, the chunks of carbon break off and plug up egr so the pintle can not close fully...the good news is the valve is not bad.... remove the valve, carefully clean the pintle free of debris. start the vehicle with egr valve out..make sure wiring for valve is out of the way....it will be very loud..rev it up and down a few times to help purge carbon chunks out of the intake. reinstall valve..this should help you..

ps your 4 thumbs up is appreciated!

Jun 06, 2009 | 1994 Oldsmobile Bravada

Not finding what you are looking for?
1994 Buick LeSabre Logo

479 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...