Question about 1994 Ford Escort

1 Answer

Brake line is leaking in front of the driver side rear wheel where the hose meets a bracket, is this bracket a connecter or just a holder for the lines?

Posted by on

1 Answer

Bracket should be welded to body.
Rubber Hose goes into it ,and is held with a clip.
If you have a rusted steel line,you will have to buy the line,bend and flair yourself,to duplicate the rusted out one.

Posted on May 26, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Brake Line Replacement on 1996 Olds Ciera


If you need to replace a brake line, you're going to have to bleed the line of air once you remove the broken one. I would highly suggest having an Autozone Tech. explain how to get that accomplished (they have always been very helpful to me).

Nov 18, 2013 | Cars & Trucks

2 Answers

Replaced some brake line, rear pads and one rear wheel cylinder. Now no pressure and nothing happening when trying to bleed.


Does the car have ABS ? And does it have an equalizer block for the 4 wheels ?
It sounds like the ABS has been affected, or there is an equalizer block that is stuck on the front wheels only.
Can you open the bleeder or the rear line on the master cyl and get fluid to come out by depressing the pedal ?

Jul 07, 2013 | 1997 Mercury Tracer

1 Answer

1991 buick park avenue brake problem had busted brake line on drivers side rear brake so i fixed it then bleed the brakes.aint getting no brake fluid comming out of the passenger side rear so took of the...


Hi Chris, The brake system is basically very simple. If you have duel braking on your vehicle, the usual method is having two brakes operate on the front with for example the left rear and the other system will also operate two front and the right rear. This type of system will have two calipers on each of the front wheels. The tandem system works in a slightly different way, having the forward part of the cylinder pressurizing the rear brakes and the rear part of the cylinder pressurizing the front. I think under the circumstances you are describing, I would have a friend sit inside and pump the brakes repeatedly until the system becomes pressurized (maybe twenty thirty times of pumping the brake pedal) and then ask him or her to keep it pushed firmly down until you find out where its leaking. The amount of brake fluid you report having been sed would indecate a severe leakage. Check the lower parts of the rear wheels for signs of leaking wheel cylinders and then dito for the front wheels. Any signs of wetness at these areas and along the brake system (the plumbing or pipe work) will indicate where the leakage is. If you cannot identify a wheel which is leaking, carefully inspect around and blow the master cylinder and if this no sign go along the fluid lines, taking special note of where the damaged pipe was repaired. If there is a blockage in the line, air may be trapped at that point causing difficulty in pressurizing. Once the place of leakage has been identified it must be attended to before bleeding the system. When bleeding, begin with the wheel furthest from the master cylinder, and work your way back to the master cylinder one wheel at a time, until you reach the closest.Keep in mind that you may find it required to pump the pedal many many times before opening the bleed nipple.Regards John

Oct 29, 2011 | 1991 Buick Park Avenue

2 Answers

Looking for a picture of back brake system for a 1999 ford f-150


Hello, I can tell you where everything is at. Did all my lines in Feb 2011. The rear lines on a F150 come from each rear wheel and they are rubber until the end of their brackets. Metal lines take over and meet at a vent tube holder on the Drivers side of the axle. An overhead rubber line with a splitter is bolted to a threaded vent tube and each rear wheel line fits in the brass block that is part of the Rubber line.

Each rear wheel line has a different size fitting to avoid mix ups. The brake line is the same diameter throughout. All use inverted flare fittings. It is a pain to get the fittings beforehand as they are mixed sizes.

The rubber line with a splitter meets a metal line topside of the frame around the frame hump for the rear wheels. The line is on rubber hangers as it travels toward the front of the truck and meets a metal union just short of the fuel filter. The metal line goes through the frame and tightly runs past the bottom of the Drivers fender and goes outside the frame until it meets the front wheelwell.

The same line crosses back into the inside of the frame and runs parallel with the frame, past the A arms and then ends up attaching to the ABS unit.

The Dealer probably does not have preformed lines. Every combination of bedsize and cabsize will determine how long some of the brake lines are. (Based on wheelbase.)

You have 2 choices. Get a preformed Stainless kit with front lines too, around $200. Make your own and spend hours assembling, bending, and flaring fittings after buying the line and the fittings.

You can go with cheap lines or use what I did, a copper/nickel mixed metal line that Volvo perfected with an extended salt corrosion resistance. It really is a job you only want to do once.
Gotta hand it to the brake mechanics who do it every day.

Here is a Summary. 2 Rubber hoses from each wheel, 2 metal lines to the threaded brass block on the vent tube. 1 rubber hose with the brass block. Then a long run of brakeline, then a connection around the fuel filter, and another long run of brakeline outside and back inside the frame to the ABS unit.

I wish you luck on this repair. I hope my Solution is very helpful.

May 29, 2011 | Ford F-150 Cars & Trucks

1 Answer

NO. NEED A PICTURE REAR BRAKE LINE ABOVE WHEEL WELL AND GAS TANK.


Hello, here's the deal with that brake line. Most of the line is wrapped in a steel spring from about 5-6 inches from the rear bake hose till around the transfer case and then it starts back up again and runs all the way up to the ABS Hydralic Control Unit. What you need to do is forget the original line. It is fastened to the left side of the frame and pinched in very tight in several areas that your not going to get it out. What you should do is get a roll of 3/16 polycoated brake line with US threads. Run that from the HCU to your left rear brake hose. It will tread right into the brake hose, but I am not sure about the HCU. Ford has a tendency of using metric fitings on the stuff up front and standard for all the other fittings. I would also get a new hose for the rear because it will probably break when you try to get the line off. This is what I did with mine. I cut the brake line with snips right about the hose connector. Then I bent the metal bracket that holds the hose to the chassis down. This allowed me to get the hose off of the bracket easier. You can always bend it back up when your done. If you change the hose, you might want to consider getting new nuts or even new lines for the rear wheels. Brake lines seem easy when you start it. But they always tend to need more then think when you start out. Oh yeah, and before you run that brake line along and though the chassis. Wrap the end with electrical tape to keep all the rust and mud out of the line. I hope this helps.

Feb 19, 2011 | 1994 Ford Explorer Limited

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

2 Answers

Where is the fuel filter located on a 2005 Lincoln LS? I drove my LS just before empty. Now I notice when I'm driving it's a little sluggish when trying to accelerate. I would like to change the fuel...


The fuel filter is behind the driver's side wheel. Here is the procedure....


  1. Before servicing the vehicle, please familiarize yourself with safety procedures.
  2. Relieve the fuel system pressure.
  3. Disconnect the negative battery cable.
  4. Remove the left front wheel well rear splash shield.
  5. Disconnect the fuel tube quick release fittings from both sides of the fuel filter.
  6. Remove the fuel filter bracket mounting bolt, fuel filter bracket, and the fuel filter.

To install:
  1. Install or connect the following:

    Fuel filter into the bracket making sure the flow direction is correct. Tighten the clamp to 15-25 inch lbs. (2-3 Nm). Fuel lines. Tighten the fittings to 22 ft. lbs. (30 Nm).
  2. Tighten the bracket bolts to 62 inch lbs. (7 Nm).
  3. Start the engine and check for leaks.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

May 18, 2010 | 2005 Lincoln LS

3 Answers

How do i remove the rear rotor on a 2000 ford explorer xlt


  1. Disconnect the brake hose.
  2. Remove bolt.
  3. Disconnect the rear wheel brake hose (2A442).
  4. Remove the copper washers and plug the brake hose.
  5. Disconnect the brake hose.
    1. Remove bolt.
    1. Disconnect the rear wheel brake hose (2A442).
    1. Remove the copper washers and plug the brake hose.
      syn~us~en~file=dh0472a.gif~gen~ref.gif
    1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
      Remove the rear disc brake caliper (2552).
      1. Remove the brake caliper bolts (2W303).
      1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
      syn~us~en~file=gh0619a.gif~gen~ref.gif
    1. Inspect the rear disc brake caliper for leaks.
      • If leaks are found, disassembly is required. Refer to Caliper in this section.
      syn~us~en~file=gh1478a.gif~gen~ref.gif
    Installation
    1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
      NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
      NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
      Install the rear disc brake caliper.
      syn~us~en~file=dh0528a.gif~gen~ref.gif
    1. Install the rear wheel brake hose.
      • Connect the brake hose and install the caliper flow bolt.
        • Use new copper washers.
      syn~us~en~file=gh0621a.gif~gen~ref.gif
    1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
    1. NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.
      Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
    1. Verify correct brake operation.
  6. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.
--------------------------------
Installation
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
    NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
    NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
    Install the rear disc brake caliper.
  1. Install the rear wheel brake hose.
    • Connect the brake hose and install the caliper flow bolt.
      • Use new copper washers.
  1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
  1. NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.
    Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Verify correct brake operation.

May 06, 2009 | 2000 Ford Explorer

1 Answer

Brake line diagram


Brake Lines and Hoses
Double-walled steel line is used in the hydraulic lines between the brake master cylinder and the front tube connector, and between the brake master cylinder and the flexible brake hose at the rear wheels.
Double-flared brake lines provide good leak-proof connections.
When replacing hydraulic brake lines, hoses, or connectors, tighten all connections securely. After replacement, bleed the brake system; refer to Section 206-00 .
The wet appearance of the outer cover of the rubber brake hose is referred to as "sweating." This is a normal condition for neoprene rayon braid hose and is not a sign of leakage or cause for replacement of the hose.

Hydraulic Brake System Components — Non-ABS

dff7165.gif
Item Part Number Description 1 2005 Power Brake Booster 2 2455 Brake Pedal 3 2261 Rear Wheel Cylinder 4 2552 Rear Disc Brake Caliper— (Mexico Only) 5 2B120 Disc Brake Caliper—, Front 6 2B091 Brake Pressure Control Valves 7 2140 Brake Master Cylinder

May 02, 2009 | 1998 Mercury Tracer

Not finding what you are looking for?
1994 Ford Escort Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...