Question about 1992 Mazda 929

1 Answer

I have a 1992 Mazda 929 with the passenger side low-beam headlight out. What is the easiest way to access the bulb to replace it?I realize this is elementary to most.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

You'll need a 10" socket, a rachet, & extension. Remove the bolts holding the head light & remove the head light housing. From there you can access & change the bulb. It only takes a few mins!

Posted on Jul 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace Low beam headlight bulb


Gain access to burned out bulb, disconnect power line and replace with new bulb.

Oct 06, 2016 | 2009 Buick LaCrosse

1 Answer

Passenger low beam won't light. New bulb did not help, fuses are good. What else can I check ?


low beam won't light Richard, faulty bulb socket module or wires, check and repair.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How to Fix Low Beam Headlight

Low beam headlights out High beam working

High beams ok but not low beam one side only TDIClub Forums

Mar 06, 2016 | 2011 Mazda CX-9

2 Answers

Driver side headlight goes dim on high beam while passenger side is bright


bad connection or bad earth check all connection or bulb

Jan 24, 2016 | Cars & Trucks

4 Answers

I have a 2006 civic SI. DRL indicator is on, driver side low and high beam ok. Passenger side low beam ok but DRL and hi beam not working. Any help is appreciated.


When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(
45d1f6ac-2983-42b9-a46c-30ef441b89e7.jpg

Nov 29, 2013 | 2006 Honda Civic

1 Answer

2007 Mazda 6 headlight


Then the light has a leak and moisture is getting in.

Jul 24, 2012 | 2007 Mazda 6

1 Answer

I have a 2004 Jeep Gran Cherokee Limited - the passenger side low beam headlight bulb was out so I opened the hood to see if I could easily access the bulb,realized its in a tight space, what is the...


Hello Harry,

You need to remove the headlight assembly. to do this with the hood open looking down on the headlight you will see one screw remove this screw then grasp the upper outboard and lower inboard corners of the headlight and pull outward.

This will give you access to the bulb sockets. When instilling the ne light bulbs be careful not to touch the glass part of the bulb any oil even a slight amount from your fingers will drastically reduce the life of the bulb.

Regards,
netvan

Feb 21, 2011 | 2004 Jeep Grand Cherokee

2 Answers

Bulb replacement for passenger side low beam on 2003 Mazda6


Google "mazda6club" - a very good forum and search "changing headlight bulb. Hope this helps.
Cheers,Peter

Mar 01, 2010 | 2003 Mazda Mazda6

1 Answer

I can't get to the high beam bulbs on our 2005 Odyssey. How do I remove the headlight for easier access to the bulbs?


The procedure doesn't call for removing the headlight assembly. It is as follows:
The high beam headlight bulb and the low beam headlight bulb are replaced the same way.

Open the hood. To change the high beam headlight bulb on the passenger’s side, remove the power steering fluid reservoir from its holder by pulling it straight up.

Remove the electrical connector from the bulb by pushing on the tab and pulling the connector down.

Remove the bulb by turning it one quarter turn counterclockwise.

Insert the new bulb into the hole and turn it one-quarter turn clockwise to lock it in place.

Push the electrical connector back onto the bulb. Make sure it is on all the way.

Turn on the headlights to test the new bulb.

If you replaced the high beam headlight bulb on the passenger’s side, reinstall the power steering fluid reservoir.

Hope this helps, but if you are having some specific problem leave a more detailed comment and I will try to help you.

Dec 26, 2009 | 2005 Honda Odyssey

Not finding what you are looking for?
1992 Mazda 929 Logo

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...