Question about 2005 Ford Futura

Open Question

How to change ford ba rh front electric window regulator

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jasperoni
  • 203 Answers

SOURCE: driver side window regulator

I would suggest replacing the whole regulator. They do offer the plastic slide pieces seperatly but usually the regulators bend and cause premature breakage of new component. If you can just replace the slides-remove the regulator and drill out existing piece if it is broken off in regulator. Next take a ball peen hammer and peen new metal into a mushrrom to secure it to existing regulator. I would remove the slider from the glass and push window all the way up and secure with a suction cup to keep it from falling down. Then take off the 2 screws securing the motor harness(disconnect the battery because one wire is hot and pay attention to the placement of the wires when they are resecured-it will just work in the opposite fashion if the polarities are reversed). Then take out the nuts and bolts securing the regulator to the door frame. If you figured out how to take off a 126 door panal you should be able to figure out the regulator position in the shell. Once the regulator is out remove the motor and secure it to the new regulator. Inspect the teeth on the motor and lube with grease (white lithium grease is what I use-wheel bearing grease is fine but it can be messy). Then "fish" new regulator into the door and secure nuts(use red locktight so they do not loosen up in the future).Then slide window down and slide in new plastic slides into window glass frame-you will want to leave the regulator loose and may have to start one of the slides before you secure regulator to door. Lube up the run channels and slides with grease. Snug regulator and operate window with regulator partially loose to let window find the best position with the lease stress and then secure regulator. It isn't as bad as it looks and with a new regulator it will be more self explanitory. Worse case senario remove the other rear panal and copy that regulator position. Good luck I hope I have been helpful.

Posted on Aug 08, 2009

  • 508 Answers

SOURCE: 2003 explorer front passenger window regulator/motor replcement

You will first need to remove the door panel on the inside. Then you will need to remove the window glass from the track it rests in. Then you need to undo all the screws that attach the regulator inside the door. At the top of the door where the glass slides up and down remove the inner and outer window track guides. Then very carefully maneuver the regulator up and out the top of the door. Reverse the procedure to replace. It sounds easy, but you need to almost be double jointed to do this. So, have great patience while doing this task. Good luck.

Posted on Feb 26, 2009

  • 43 Answers

SOURCE: electric window regulator for front driver side.

Your best bet is to go through your local dealership. They will have the part you need and it should be the exact one for your car.

Posted on Jul 21, 2009

  • 210 Answers

SOURCE: I need rr rh electric window regulator were can I

You can buy a new one at the dealer, depending how versatile you are, you can get one at the junk yard. Many of them let you pull your own parts and sell them to you cheaper.

Posted on Apr 24, 2010

  • 7353 Answers

SOURCE: 1994 ford crown vic front pass. side power window regulator...

Yes it is. They will need to be drilled out. Thats the best way, some people try to put bolts on, but I dont advise it.

Posted on May 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change bulb 2004 ford falcon ba xr6


Remove the battery if it is RH side bulb then remove dust cover and you are at the rear of the bulb

Apr 30, 2014 | 2005 Ford Falcon

1 Answer

I need instructions, written and hopefully with photo examples, that will teach me how to replace the passenger side mirror on my Ford Sport Trac. The truck is a 2004 model and the mirror is motorized...


Removal and Installation
NOTE: LH door is shown, RH door is similar.
  1. Disconnect the battery. For additional information, refer to Section 414-01.
  1. Remove the front door window control switch panel and trim covers.
    1. Remove the door screw cover.
    1. If equipped with power windows, remove the door window control switch and disconnect the electrical connectors.
    1. Remove the door handle bezel
ganyapr_2.jpg
3. Remove the door handle screws


ganyapr_3.jpg
  1. If not equipped with power windows, remove the screw and the window regulator handle.
  1. Remove the screws and the front door trim panel.
ganyapr_4.jpg6. Remove the door speaker Remove the screws.
Disconnect the electrical connector.
Remove the door speaker.
7. Disconnect the exterior rear view mirror electrical connector
ganyapr_5.jpg
8. Remove the nuts and the exterior rear view mirror.
Feed the power mirror wiring through the opening in the front door.
ganyapr_6.jpg
9. To install, reverse the removal procedure

i hope that this could help you
2010&c18=modelyear&c20=n712771&c35=wsm%2cfront%20door%20trim%20panel%2cs5r%2c501-05%2cremoval%20and%20installation&s=1280x800&c=32&j=1.3&v=y&k=y&bw=931&bh=469&ct=lan&hp=n&[aqe]

Feb 20, 2011 | Ford Explorer Sport Trac Cars & Trucks

3 Answers

1997 mercury grand Marquis driverside rear window motor works but window won't go up. Inner door panel off. Metal cable with a black foam cover and pink plastic clip off. Can't figure what it fits to.


usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    3. Disconnect window regulator electric drive harness connector.
    4. sva~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Be careful not to strike or scratch front door window glass because it can break.
      Remove window regulator electric drive retaining screws through holes.
    5. Remove window regulator electric drive (23394) from front door power window regulator.
    6. Raise front door window glass to full up position by hand and secure with tape.
    7. Go to Step 5.

  2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
  3. Remove front door window glass as described.
  4. Disconnect window regulator electric drive harness connector.
  5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.

    Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
  6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
  7. Remove two window regulator retaining nuts.
  8. Remove front door power window regulator from front door (20124).
Installation
  1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
  1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
  1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
  1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
  1. Install two upper front door power window regulator retaining nuts.
  1. Install window regulator electric drive with three screws. Do not overtighten screws.
  1. Connect the window regulator electric drive harness connector.
  1. Install front door window glass.
  1. Adjust front door window glass as described.
  1. Install front door trim shield and front door trim panel. Refer to Section 01-05 snorkelbobby_38.gif

Feb 14, 2011 | 1997 Mercury Grand Marquis

1 Answer

How to replace the window regulator on the front windowsof a 2005 ford 150 triton pickup truck


  1. Remove the front door trim panel.
  2. Remove the front door watershield.
  3. Secure the front door window glass in the full upward position with tape.
  4. Remove the front door window glass-to-regulator assembly bolts.
      • Loosen the glass clamp fasteners through the 2 vertical slots in the inner door panel.
      • To install, tighten to 9 Nm (80 lb-in) .
    1. Disconnect the front door window electrical connector.
    2. Remove the front door window regulator bolts.
      • To install, tighten to 11 Nm (8 lb-ft) .
    1. Remove the front door window regulator and motor.
    2. To install, reverse the removal procedure

Aug 15, 2010 | 2005 Ford F-150

2 Answers

Need to pull the panel off driver side door of 2004 ford f150


SECTION 501-01: Body System — Interior 2004 F-150 Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/17/2004 Front Door Trim Panel adobe.gif Printable View (229 KB) Removal and Installation
NOTE: LH side is shown. RH side is similar.
  1. Remove the front door speaker. Refer to Section 415-00.
  1. If equipped, remove the window regulator handle.
    1. Separate the handle cover from the handle.
    1. Remove the screw.
    1. Remove the window regulator handle.
    1. Remove the spacer.
    r12386a.gif
  1. Remove the parts in the order indicated in the following table.

    a0005479.gif
    Item Part Number Description 1 224A60 Cover plate 2 N602704-S301 Screws (2 req'd) 3 14B132A (RH) / 14B133B (LH) Window control switch 4 14630 (RH) / 14631 (LH) Window control switch electrical connectors 5 W505424-S301 Bolt 6 W701930-S424 Bolts (2 req'd) 7 19A034 Water shield 8 W709132-S300 (High series trim) / W709133-S300 (Low series trim) Speaker standoff (2 req'd) 9 219A65 (LH)/ 219A64 (RH) Front door handle
    Removal Note 10 23942 (RH) / 23943 (LH) Front door trim panel
    Removal Note
  1. To install, reverse the removal procedure.
Item 9: Front Door Handle Removal Note
  1. Guide the door handle through the opening in the trim panel.
Item 10: Front Door Trim Panel Removal Note
ani_caut.gif CAUTION: Do not pull directly outward on the front door trim panel, as damage may occur.
  1. Lift upward and remove the front door trim panel.

2010&c18=modelyear&c20=n717901&c35=wsm%2cfront%20door%20trim%20panel%2cs42%2c501-01%2cremoval%20and%20installation&pid=wsm%2ctitle%20page%202004%20f-150%2cs42&pidt=1&oid=functiononclick%28%29%7bdosearch%28%29%3b%7d&oidt=2&ot=img&oi=27&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=491&ct=lan&hp=n&[aqe]

Apr 03, 2010 | 2004 Ford F150

1 Answer

How do you replace the regulator for the power window on the 2002 ford explorer


Regulator - Power Windows - Front Door
  1. Remove the front door trim panel as follows:
    1. Remove the front door handle bezel.
    2. Remove the front door window/lock control switch bezel.
    3. Disconnect the window/lock control switch electrical connectors.
    4. Remove the 3 front door trim panel screws.
      CAUTION To avoid damaging the trim panel, do not pull directly outward to carry out this step.
    5. Lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
    6. Remove the exterior mirror control switch from the front door trim panel.
  2. Remove the front door speaker.
  3. Remove the interior molding.
  4. Disconnect the door lock actuating rod at the door handle assembly:
    1. Release the door lock actuating rod clip.
    2. Position the door lock actuating rod aside.
  5. Remove the front door weather shield.
    CAUTION Make sure the holes in the glass bracket do not become enlarged during the rivet removal process. If the holes become enlarged, the new rivets may become loose, resulting in clicking noise concern.
    NOTE Some vehicles may use rivets to attach the window glass to the window regulator assembly. Use a 4.5 mm (0.1772 in) drill bit to drill out the glass-to-regulator rivets.
  6. Remove the 2 front door window glass-to-regulator bolts or rivets.
  7. Position the front door window glass as necessary to access the front door window glass-to-regulator bolts or rivets.
  8. Secure the front door glass in the full up position with tape.
  9. Disconnect the window regulator motor electrical connector.
  10. Remove the 4 window regulator assembly nuts.
  11. Remove the window regulator assembly.

    0b00886.jpg

    Fig. Exploded view of the front door and power window components-2005 Explorer and Mountaineer

To install:
  1. Position the window regulator assembly.
  2. Install the 4 window regulator assembly nuts. Tighten to 89 inch lbs. (10 Nm).
  3. Connect the window regulator motor electrical connector.
  4. Remove the tape securing the front door glass in the full up position.
  5. Position the front door window glass as necessary to access the front door window glass-to-regulator bolts or rivets. Install the bolt and tighten the bolts to 62 inch lbs. (7 Nm), or install new rivets.
  6. Install the front door weather shield.
  7. Connect the door lock actuating rod at the door handle assembly:
    1. Position the door lock actuating rod into proper location.
    2. Attach the door lock actuating rod clip.
  8. Install the interior molding.
  9. Install the front door speaker.
  10. Install the front door trim panel as follows:
    1. Install the exterior mirror control switch from the front door trim panel.
    2. Position the door trim panel onto the armrest to engage the panel clips.
    3. Install the 3 front door trim panel screws.
    4. Connect the window/lock control switch electrical connectors.
    5. Install the front door window/lock control switch bezel.
    6. Install the front door handle bezel.

  1. Raise the front door window glass to the full up position.
  2. Remove the interior door handle.
  3. Support the front door window glass.
  4. Disconnect the front door window regulator motor electrical connector.
  5. Remove the equalizer bracket nuts.

    4945f24.jpg
    Fig. Remove the equalizer bracket nuts-2005 Explorer Sport-Trac
  6. Remove the front door window regulator by removing the rivets and nuts.
  7. Remove the front door window regulator motor retaining bolts and then remove the motor.

    52a6816.jpg

    Fig. Remove the front door window regulator motor retaining bolts and then remove the motor-2005 Explorer Sport-Trac
To install:
  1. Installation is the reverse of the removal procedure.
  2. Tighten the regulator motor mounting bolts to 8 ft. lbs. (11 Nm).

Hope this help (remember rated and comment this).

Mar 24, 2010 | 2002 Ford Explorer

1 Answer

2003 ford taurus drivers window will not go up.


you either need a motor or motor and window regulator assembly.
SECTION 501-05: Interior Trim and Ornamentation 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Trim Panel Removal and Installation
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the front door trim panel screws.
  1. NOTE: To release the door trim panel two part pin-type retainers, first pull outward on the bottom of the door trim panel.
    Remove the front door trim panel.
    • Disconnect the electrical connectors.
c64985a.gif --------------------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Window Regulator And Motor
Special Tool(s) s2h~us~en~file=st1132a.gif~gen~ref.gif Heavy Duty Riveter
501-D011 (D80L-23200-A) or equivalent
Removal and Installation
  1. Remove the front door window glass. For additional information, refer to Front Door Window Glass in this section.
  1. Disconnect the front door window regulator motor electrical connector.
  1. Remove the window regulator rivets.
-----------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Door Window Regulator Motor Removal and Installation
  1. Close the window.
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the door trim panel. For additional information, refer to Section 501-05 .
  1. If equipped, remove the radio speaker.
  1. Position the watershield aside.
  1. Disconnect the door window regulator motor electrical connector.
  1. Remove the bolts and the door window regulator motor.
---------------------------------------------------

May 04, 2009 | Ford V6 Pony Cars & Trucks

1 Answer

Replace a window regulator in a 1994 ford explorer


wow, a lot of work to do.

Window Regulator, Front Door, Explorer Removal
srk~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel and front door trim shield . Refer to Section 01-05B .
  1. Remove inside door belt weatherstrip and glass stabilizer.
  1. Remove front door window glass as described in this section.
  1. Remove two nut and washer assemblies attaching the equalizer bracket.
  1. Remove three rivets (manual) or four rivets (power) attaching the regulator base plate to front door trim panel finish panel (23712) .
  1. Remove window regulator electric drive and front door window channel bracket from vehicle.
  1. Working on a bench, carefully bend tab flat to remove arm slides from front door window channel bracket .
  1. Install new window regulator electric drive arm plastic guides into front door window channel bracket and bend tab back to 90 degrees. Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket . Make sure rubber bumper is installed properly on new front door window channel bracket , if replacement is made.

    4a5a8fb.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Steps 7 and 8 of Window Regulator, Removal.
  1. Install front door trim panel finish panel with preassembled glass bracket into vehicle. Set the regulator base plate to window regulator electric drive using base plate locator tab as a guide.
  1. Install three (manual) or four (power) rivets (385189-S100) to attach regulator to front door trim panel finish panel . Two 1/4-20 x 1-inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (3-5 ft-lb). Equivalent metric retainers may be used.
  1. Install equalizer bracket.
  1. Install inside door belt weatherstrip and glass stabilizer.
  1. Lower regulator arms to access holes in front door trim panel finish panel . Install front door window glass as outlined.
  1. Adjust glass to ensure proper alignment with glass run. Cycle glass for smooth operation.
  1. Install front door trim panel and front door trim shield . Refer to Section 01-05B .

Apr 11, 2009 | 1994 Ford Explorer Limited

1 Answer

2004 Mercury Monterey left frnt window sector gear R&R proceedure


are you a techie? You need a heavy duty riveter to do this repair. May have to rent or borrow from auto store.

here's the procedure



Front Door Trim Panel s4w~us~en~file=adobe.gif~gen~ref.gif Printable View (251 KB) NOTE: LH side is shown. RH side is similar.
  1. Remove the parts in the order indicated in the following illustration and table.

    df2877a.gif

  2. Item Part Number Description 1 23942/23943 Mirror access panel 2 1722897 Cup assembly 3 W56904-S424 Window regulator control switch panel screws 4 14A665 Window regulator control switch panel
    Removal Note 5 W701930-S424 Front door trim panel screw 6 W701930-S424 Front door trim panel screw 7 N602703-S61 Front door trim panel screw 8 1723943 Front door trim panel 9 W705590-S300 Nut insert(s)
  1. To install, reverse the removal procedure.
Item 4: Window Regulator Control Switch Panel Removal Note
  1. If equipped, disconnect the electrical connector(s).
-----------------------------------------------------------------------------------
Door Window Glass — Front s4w~us~en~file=adobe.gif~gen~ref.gif Printable View (328 KB)
Special Tool(s) s4w~us~en~file=st1132a.gif~gen~ref.gif Heavy Duty Riveter
501-D011 (D80L-23200-A)
  1. Remove the front door trim panel. For additional information, refer to Section 501-01 .
  1. Position the watershield aside.
  1. Remove the parts in the order indicated in the following illustration and table.

    To remove individual parts, only carry out the listed steps: Part Steps Front door window glass 1, 3 Front door window regulator 1-5 Front door glass run 1, 3, 6-8
    4be8135.gif
Item Part Number Description 1 W706495-5100 Rivet (2 required)
Removal Note
Installation Note 2 N8621986 Nut (3 required) 3 21410 Front door window glass 4 W706495-5100 Rivet (4 required)
Removal Note
Installation Note 5 23200 Front door window regulator
Removal Note 6 N800507-S Bolt (2 required) 7 21596 Front door glass run 8 — Front door glass run (Part of 21596)
  1. To install, reverse the removal procedure.
Item 1: Rivet Removal Note
  1. Connect the window control switch.
  1. Connect the battery.
  1. Position the door window glass halfway down to gain access to the door window glass rivets.
    • Remove the rivets.
9391398.gif Item 4: Rivet Removal Removal Note
  1. Remove the rivets.
Item 5: Front Door Window Regulator Removal Note
  1. Disconnect the electrical connector.
  1. s4w~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Prior to power window motor removal, make sure the regulator arms are in a fixed position to prevent counterbalance spring unwind. Failure to place the regulator arms in a fixed position can cause the spring to suddenly release resulting in personal injury.
    NOTE: The counterbalance spring assists the window in the upward direction.
    Remove the bolts and the window regulator motor.
Item 4: Rivet Installation Note
  1. Using the special tool, install the rivets.
b4c4793.gif

Feb 21, 2009 | 2004 Ford Freestar

Not finding what you are looking for?
2005 Ford Futura Logo

Related Topics:

323 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...