Question about 1986 Ford Mustang

Open Question

1986 vacuum line diagram. vacuum lining destroyed. not sure what line goes where?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: No Heat..Heater Core Is Heating..Vacuum Lines?

I have a '96 Eddie Bauer Limited and it has the same problem. They told me that there is a small butterfly valvu located in the vac lines to select between hot or cold air. There is a tension spring connected to the valve, to an acutator, and to your ac contorl system. The spring on mine broke, so the valve opens and closes due to suction only. It is supposed to be about a $700.00 fix (due to the valves location by the firewall) but I have found a way around that. Try to aggressively apply the brakes making the vehicle slow rapidly, and at the same time turning on the blower fans with full bast heat selected. If this does not work, try doing the previous while going around a right hand corner. The corner will help the momentum of the valve turn in the right direction. Remember you have to switch the fan on full blast when you try either. If it works you should hear a thud as the valve flips shut and the heat should start coming out of the vents.

Good luck

Posted on Dec 22, 2008

Ad
cgtotty
  • 1 Answer

SOURCE: chevy s10 broken vacuum line

The plastic line in the wiring harness goes to the heater controls; and believe it or not , the other end goes to the vacuum tank - but its in the FENDER !!!!! behind the ABS, kinda under the drivers side hood hinge - great place to put one ain't it ? No wonder GM is going broke !! Good Luck

Posted on Dec 25, 2008

motor1258
  • 6674 Answers

SOURCE: vacuum line diagram 98 chev monte

No sticker on underside of hood or on rad support showing that?

Posted on Mar 07, 2009

  • 1 Answer

SOURCE: diagram of vacuum lines

59a5fb6.jpg
I think this is what you are looking for.

Posted on Mar 28, 2009

truekleen1
  • 46 Answers

SOURCE: 1986 Ford Ranger Vacuum lines wrong

Go to auto zone through this link And register for free then click select vehicle, add your vehicle and go to driveability and Emissions controls, than go to vacuum diagrams.

Posted on May 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1986 FORD RANGER 2.9L 4WD VACUUM LINE DIAGRAM


I had the same need on an 87 firebird what I did was go to the junk yard find the same truck with same engine and trace the lines make my own diagram, and in my case buy the hard plastic formed vacuum lines that were broken. hope that helps

Aug 25, 2014 | 1986 Ford Ranger 2WD

1 Answer

Vacuum routing diagram from the heater/ac control unit for a 1986 chrysler fifth avenue


there should be a label underside of the hood showing this but as vehicle is a bit oldish may not still be there follow this link you should find yours there
Repair Guides Vacuum Diagrams Vacuum Diagrams AutoZone com

Jul 06, 2014 | 1986 Chrysler Fifth Avenue

1 Answer

Just installed a rebuilt carb. some of the vac' lines broke during installation. Im looking for a diagram to see where Im having vac problems...


YOU SHOULD HAVE ONLY 3 VACUUM LINES 2 IN FRONT THAT'S ONE FOR INTAKE PORT VACUUM AND ONE FOR THE TRANS,THE ONE IN THE BACK GOES TO BRAKE BOOSTER.










TIM

Jan 19, 2011 | 1986 Chevrolet G20

2 Answers

I need to know where all the vacume lines go on a 1986 comanche 2.8l v6


Most vehicles have a diagram on the underside of the hood that shows the vacuum line routing. Just open your hood and look up!

Sep 13, 2009 | 1986 Jeep Comanche

1 Answer

1986 Ford Ranger Vacuum lines wrong


Go to auto zone through this link And register for free then click select vehicle, add your vehicle and go to driveability and Emissions controls, than go to vacuum diagrams.

May 13, 2009 | 1988 Ford Ranger

1 Answer

I NEED A VACUUM INE DIAGRAM FOR A 1986 FORD RANGER 2.9 EFI


Make sure that your truck vaccume line goes into the intake manifold where there is a vacuume spiggot at the base of the carb. You may have iadvertantly hooked it up to the wrong place.

Feb 13, 2009 | 1986 Ford Ranger 2WD

1 Answer

I have a 1986 gmc 2500 van and my vacuum lines are crossed up and i need help uncrossing them


Carb vacuume lines? I can direct you to a holley website .... it has a diagram that has the q-jet vacuume routing all you have to do is look at the diagram then scroll down and look at the number to see where it goes.

http://www.holley.com/data/Products/Technical/199R9881.pdf

Hope this helps.

Jan 03, 2009 | 1983 Chevrolet Silverado

1 Answer

Vacuum line diagram


if you get a chilton from any local parts store it should have them in there

Jun 10, 2008 | 1986 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5575 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...