Question about 2000 Ford F350 Super Duty Super Cab

Open Question

Replace super duty steering column bushings - 2000 Ford F350 Super Duty Super Cab

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 375 Answers

SOURCE: troubles with steering 03 Ford Super Duty Diesel?

Unfortunately this was a concern on this vehicle, even new they had a tendency to wander all over the road and **** around when hitting bumps and ruts in the road. Inspect your tie rods and ball joints to make sure they are tight, inspect the shaft that connects the steering sector to the steering column for free play. If all these are good remove and inspect the steering damper shock if it has one to make sure it is ok, if it doesn't have a steering shock install one. Ford has all the parts available to install one or you can get a kit from Rancho or other suspension parts company. And last off adjust the free play in the steering sector, you will need to set it tighter the factory specs to get the wander out, then have the alignment checked to make sure it is in spec and your truck should drive normally.

Posted on May 18, 2008

Ad
  • 1118 Answers

SOURCE: loose steering

Idler arm, pitmen arm, and tie rod ends, ball joints.

Posted on Feb 10, 2009

  • 11 Answers

SOURCE: how to replace outside mirrors on a 2002 ford f-250 super duty

you need to remove door trim panel there are (2) 7mm screws that hold panel on .. 1 is behind the lower red light lens and the other is behind switch panel for the power window switch . remove both screws and remove small black panel above door trim by pulling strait off .(now there are (4) 11mm nuts the hold mirror on 2 are behind the small rubber plugs in front of door that you can see with panel on and the other 2 are under panel that you can see after panel is removed . the wiring need to be disconneced you may have to remove speaker for acess to feed new wiring down into the door good luck

Posted on Mar 11, 2009

  • 164 Answers

SOURCE: replace ignition in steering column 92 jeep laredo

dealer has better picture they can print out for you give them a call

Posted on Jul 26, 2009

  • 2 Answers

SOURCE: 2003 Dodge Durango clunking noise in front end can

With the information given this is not a sure solution. Questions that need to be asked is when does this happen, turning at slow speedm high speed, when hitting a pot hole etc? Since you have replaced a lot of things already, assuming you have NEW good quality parts so you did not replace bad parts with new bad parts i would definitelu check the pitman arm. This runs from the stering gear to the tierod. It can give you some good clunks while steering, especially at low speed when there is a lot of resistance. Check it by having someone turning the steering wheel when watchin/feeling it.

Posted on Sep 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Okay, my boyfriend owns a 2000 ford f-250 super duty and your prolly wondering as to why im asking about this instead of him ... well im more mechanically inclined then he is lol funny huh... okay heres...


It sounds like the shift tube bushings are worn out. There are usually 2 u shaped clamps that have nylon bushings that hold the shift tube to the steering clumn. If loose, that throws off the shift position, could be btween 2 gears at once, and throws off the park - neutral safety switch. Fix that first.


snorkelbobby_53.gif Item Part Number Description 1 14A664 Air Bag Sliding Contact 2 3530 Upper Steering Column Shroud 3 3518 Steering Column Bearing Sleeve 4 3517 Steering Column Bearing 5 3511 Steering Column Lock Cylinder Housing 6 13K359 Multi-Function Switch 7 N808114 Pin 8 N805857 Steering Column Release Lever Pin 9 3D544 Steering Column Release Lever 10 3F609 Tilt Wheel Handle and Shank 11 7361 Column Shift Selector Lever Plunger 12 7210 Gearshift Lever 13 3D657 Steering Column Shaft 14 7B071 Transmission Control Selector Lever Plunger Spring 15 7G357 Gearshift Lever Pin 16 7212 Transmission Column Shift Selector Tube 17 N806582 Tilt Column Pivot Screw 18 7C464 Transmission Control Selector Lever Spring Clip 19 7E400 Gearshift Tube Bushing Clamp 20 - Spacer (Fixed Column) 21 3E729 Steering Shaft (Fixed Column) 22 3F527 Lever Assembly (Manual Transmission) 23 3F530 Pin (Manual Transmission) 24 3F752 Brake Shift Interlock Solenoid 25 7335 Gearshift Lever Socket Bushing 26 7A216 Transmission Shift Selector Position Insert 27 7302 Transmission Selector Lever Arm and Support 28 7E395 Shift Cable and Bracket 29 7210 Gearshift Lever 30 3E691 Steering Column Shift Lock Pawl 31 7W441 Gearshift Lever Pin 32 3676 Steering Column Instrument Panel Bracket 33 3D681 Steering Column Lower Bearing Retainer 34 3517 Steering Column Bearing Sleeve 35 3L539 Steering Column Bearing Tolerance Ring 36 3C674 Steering Column Lower Bearing Spring 37 3C131 Sensor Ring 38 3518 Steering Column Bearing 39 N806423-S56 Steering Column Retaining Nuts 40 14A163 Wiring Harness Retainer 41 3F723 Steering Actuator Housing 42 3B663 Steering Column Lock Lever Pin 43 11572 Ignition Switch 44 3D655 Steering Column Position Spring 45 3D653 Steering Column Locking Lever (LH) 46 3B768 Steering Column Position Lock Spring 47 3B662 Steering Column Locking Lever (RH) 48 3E715 Lower Steering Column Lock Actuator 49 3E696 Steering Column Lock Spring 50 3E691 Steering Column Shaft Lock Pawl 51 3E723 Upper Steering Column Lock Lever Actuator 52 3E695 Steering Column Lock Cam 53 3D656 Steering Column Tilt Flange Bumper 54 14A163 Wiring Harness Retainer 55 391727-S304 Shroud Screws 56 3530 Steering Column Shroud 57 3E717 Steering Column Lock Gear 58 3E700 Steering Column Lock Housing Bearing 59 3C610 Bearing Retainer 60 11582 Ignition Switch Lock Cylinder 61 3L539 Steering Column Tolerance Ring 62 3520 Steering Column Upper Bearing Spring 63 3C610 Snap Ring

Apr 05, 2011 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

Where do i find the turn signal flasher on 2000 ford f350 super duty lariat


I would turn the turn signal or the hazard flashers on to find the respective flasher that 'clicks' when you hear and feel it, if functioning correctly.

It probably is buried underneath the steering column area under the dash.

Aug 29, 2010 | 2000 Ford F350 Super Duty Super Cab

1 Answer

2003 ford f250 super duty 7.3ltr I switch it from 4 wheel drive back to 2 wheel and it blows number 45 fuse. Also sometimes when i go from park to reverse it blows the same fuse.


Hi,
The wiring from your overdrive cancel (or tow/haul) switch is shorting in your steering column. Remove the plastic trim from around the steering column. From above the steering column look in the area where the gear shift meets the column. You will see a pair of wires (twisted) wrapped in a black tube. Examine these wires really closely and I am sure you will find an area where they have rubbed thru. Wrap a little electrical tape tightly around the area and you are good to go. To get the top plastic piece off of the column you may need to remove the ignition key cylinder. turn the key to the run position. Under the cylinder on the column is a small hole. Push a pick into the hole while you wiggle and pull outward on the key cylinder. The cylinder should pull out and allow you to remove the plastic trim. The cylinder must be in the run position when you reinstall it too.
I hope I was descriptive enough. I hope this helps you out!

Apr 07, 2010 | 2002 Ford F250 Super Duty SuperCab

1 Answer

Horn fuses all good but when i push button i don't have any horn or even hear relay. this all started after i had new bushing installed in steering wheel. Could the wires behind the wheel have been cut ?


Do you mean you had new bearings put in the top of the steering wheel column ? Do you have a tilt feature or a tilt / travel feature? Regardless, yes, the wire could have been cut, but I would suspect a poor connection in the slip ring or the horn pad connector was just not connected to the connector at the slip ring when it was put back together. Do you have cruise control switches on your steering wheel ? If so , I would pull steering wheel and check the slip ring connections first.

Mar 16, 2010 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

Intermittent turn signal operation


The multifunction switch mounted to the steering column is the source of the problem. Replace the complete assembly.

Feb 25, 2010 | 2000 Ford F350 Super Duty Super Cab

1 Answer

HOW DO YOU REPLACE THE BEARINGS IN THE STEERING COLUMN IN A FORD F450 2002 fixed steering coulmn


no one replaces the bearings. it is far more difficult than you might think. special tools are required.
buy a complete used one.

Jan 26, 2010 | 2002 Ford Super Duty F 450

1 Answer

Shifter wont go into 1st and sometimes wont go


It sounds like the bushings on the steering column that hold the shifter in place are worn out ot the brackets holding the bushings in place have come loose allowing for excessive movement with the shifter shaft. These things also had a problem with a bracket coming loose at the lower part of the steering column. You can look up under the dash (laying on your back) and find the shifter cable where it attaches to the shifter shaft. There are tree bolts that hod this bracket on. If they come loose you will have this same problem To fix it you need a T-30 torx socket and a ratchet to tighten these three bolts.

Nov 07, 2009 | 2000 Ford F250 Super Duty Crew Cabs

2 Answers

2003 Ford F-250 Super Duty 6.0 liter 4x4 diesel steering 71000 miles


check out the steering stabilizer(it's the shock on the steering linkage) for wear. If it shows signs of leakage replace it.

Jun 29, 2008 | 2007 Ford F-250 Super Duty Lariat

Not finding what you are looking for?
2000 Ford F350 Super Duty Super Cab Logo

Related Topics:

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...