Question about 1992 Honda Prelude

1 Answer

Honda prelude 1992. rubber boot split not sure which one it is. It appears to be covering a rod which leads towards the front wheel on each side. It is the rearmost boot cover.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 462 Answers

CV joint boot.(cv boot)
It's easier to replace the whole axle , they are cheap in our days.

Posted on May 26, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Troubleshooting rack&pinon problems


will need to jack front end up,check the wheels turn side to side freely before removing wheels , visually check the steering system looking for splits etc to the rubber steering arm gaiters, the track rod end ball joints, where the steering coloum enters the car for damage etc to the rubber boot , hope this helps

Oct 30, 2014 | Cars & Trucks

1 Answer

Power window works on drivers side dont on passenger side


So the passenger side window isnt working ,have you checked for power to the motor and power to the switch ,could the fault be in the rubber boot from the door frame to the door ? damaged cable unless you check these things out first and then explain i cannot possibly tell you what to do

Apr 25, 2012 | 1992 Honda Prelude

1 Answer

I need a diagram of strut rod bushings for a 95 honda accord


sorry dont have a diagram here is a how to

  1. Disconnect the negative battery cable. If equipped with an air bag, properly disable the Supplemental Restraint System (SRS), as detailed in Chassis Electrical .
  2. Elevate and safely support the front of the car.
  3. Remove the wheel.
  4. Loosen the nut at the rear of the radius rod. Remove the nut, washers, bushing, etc. Keep them in the correct order for reinstallation.
  5. Remove the bolts securing the rod to the control arm. Remove the rod.

To install:

  1. Inspect the bushings carefully for wear or deformation. Replace them if any damage is found.
  2. Fit the rod into place and install the bolts at the control arm. Tighten the bolts to 40 ft. lbs. (55 Nm) on Accords through 1989 and Preludes through 1991. On 1990-95 Accords and 1992-95 Preludes, tighten the bolts to 76 ft. lbs. (105 Nm).
  3. Install the bushings, washers and spacers on the rod. Install a new locking nut. On all except 1992-95 Preludes, tighten the end nut to 33 ft. lbs. (44 Nm). On 1992-95 Preludes, tighten the nut to 40 ft. lbs. (55 Nm).
  4. Install the wheels and lower the vehicle.
  5. Properly enable the SRS system, if equipped, and connect the negative battery cable.

Jun 17, 2011 | Honda Accord Cars & Trucks

1 Answer

Set timing on a 1992 honda prelude, 2.3 engine, I REPLACED THE DISTRIBUTER AND NOW ITS COMPLETELY OUT OF TIME, detailed instructions please


  1. Locate the service check connector and, if applicable, remove the cap. On 1988-91 Preludes, the cap is yellow and the connector is located next to the vacuum control box in the engine compartment. On 1992-95 Preludes, the service connector is located under the middle of the dash. On 1990-93 Accords, the connector is blue and is located behind the right front kick panel, under the dashboard. On 1994-95 Accords, the service connector is located behind the glove box. Use a jumper wire to connect the two terminals of the service connector.
  1. Following the manufacturers instructions, connect a timing light to the engine. The positive and negative leads connect to their corresponding battery terminals and the spark plug lead to No. 1 spark plug wire.
  2. Make sure that all wires are clear of the cooling fan and hot exhaust manifolds.
  3. Set the parking brake and block the front wheels. Start the engine. Check that the idle speed is set to specifications.
  4. Point the timing light at the timing marks. On all models except 1994-95 Accords, the marks are on the flywheel. On the 1994-95 Accords, the timing marks are on the crankshaft pulley. When the engine is idling, the red mark must align with the pointer. Some timing marks are indicated by 3 lines; the center one must be aligned with the pointer.

  1. If necessary to adjust the timing, loosen the distributor hold-down bolt(s) and/or nut and slowly rotate the distributor in the required direction while observing the timing marks.
  2. To complete the adjustment operation, tighten the hold-down bolt, taking care not to disturb the adjustment.
  3. Switch the engine OFF . Reinstall the rubber plug in the timing window and remove the timing light. Remove the jumper wire.



0900c1528005f368.jpg

Fig. Fig. 4: Service connector on 1988-91 Preludes


0900c1528005f36b.jpg

Fig. Fig. 5: Service connector on 1992-95 Preludes

Mar 03, 2011 | 1992 Honda Prelude

1 Answer

Fit steering rack boots on a 93 honda accord


Simply jack the vehicle up / remove the wheel on that side / removed the split pin and castellated nut on the tie rod end / using a soft hammer or ball joint splitter hit the end of the ball joint arm till the tie rod falls out / loosen the tie rod lock nut then unscrew the tie rod. Remove the boot clips / clamps and remove the torn rack boot. Replacement is the reverse of the above.
NB = A wheel alignment is required to correct the adjustment of the tie rod end ASAP.

Oct 19, 2010 | 1993 Honda Accord

3 Answers

When I turn there is a grating sound, both left and right turns--doesn't happen at low low speeds or on very easy turns. 2003 honda civic


It sounds like the CV joints need some attention. These are covered with rubber boots and if the boots crack they let in water and/or dirt which cause the joints to make a popping or grinding sound. Turn the wheels left or right and look under the car towards the inside of the wheels. The boots are right next to the back of the wheels. Look for cracks in the rubber. If you can, push on the boots and check for small cracks. If they are cracked, have them looked at immediately. The longer they go like that the more damage will be caused. Thanks for using fixya.

Nov 19, 2009 | 2003 Honda Civic

2 Answers

My 1992 Honda Accord EX-R makes a clunking/rattling sound...


It's probably your cv (constant velocity) joint. Jack up the honda and put it on safety stands, look at the area behind the center of both front wheels, there is a rubber boot. This boot protects the cv joint from dirt, road grime, water, salt, etc. If you see splits in it or grease on the boot, it has deteriorated, and is letting contaniments in. The damage has already been done if it makes a rattling noise going around corners at slow speed. I changed both cv joints (purchased rebuilt axles for $49 each) in my 92, but it is a big job labor wise. There's a lot to take apart to remove the axles.

Jul 29, 2009 | 1992 Honda Accord

1 Answer

Replace airbag on `92 honda accord


When an SRS cable reel assembly is removed and set aside during vehicle repairs, the cable reel may rotate inside the assembly so it is no longer centered. If the assembly is reinstalled with the reel off-center, the cable can break when the steering wheel is turned to full lock. The cable reel holding fixture locks the reel while the assembly is off the vehicle, keeping it centered for reinstallation.
CABLE REEL REMOVAL PROCEDURE
1. Follow the procedure in the appropriate service manual for disconnecting the battery, and removing the dashboard panels, steering column covers, airbag, and steering wheel.
^ Always install short connectors on the connectors for the driver's and passenger's (if so equipped) airbags.
^ Make sure the front wheels are pointed straight ahead before removing the steering wheel.
2. Verify that the cable reel is centered; the yellow gear tooth is lined up with the alignment mark on the cover. Install the cable reel holding fixture in the cable reel assembly as shown. Use a TORX T-10 wrench.
3. Disconnect the 6-P connector, then remove the cable reel assembly.
CABLE REEL INSTALLATION PROCEDURE
1. Verify that the front wheels are still pointed straight ahead.
2. Reinstall the cable reel assembly, and reconnect the 6-P connector.
3. Remove the cable reel holding fixture.
4. Follow the service manual procedure for reinstallation of the steering wheel, airbag, steering column covers, and dashboard covers.
5. Verify SRS operation as described in the service manual. Road test the vehicle.
^ If the steering wheel spoke angle is not correct, change it by adjusting the tie rod ends. Do not remove and reposition the steering wheel.
PARTS INFORMATION
Cable reel holding fixture:
For 1992-95 Civic and Ohio-produced 1992-95 Accord
P/N 77900-SPO-999, H/C 4733564
For 1991 Accord Wagon, 1992-95
Prelude, 1995 Odyssey and Japan-produced
1992-95 Accord
P/N 77900-SM5-999, H/C 4733572
WARRANTY CLAIM INFORMATION
Use the Flat Rate Manual information for the repair being performed.

Jan 28, 2009 | 1992 Honda Accord

1 Answer

Honda prelude 1992 i have spark fuel air car turns over fine it should start but it won't start


try checking the timing...take the valve cover off...remove the rubber cover for your inspection window on the flywheel... line up the white line on your flywheel with the pointer...once your lined up at tdc with the flywheel check your cam sprockets and make sure they are in the right alignment...also take your cap off and look at where your rotor is pointing..making sure it is pointing at #1 cylinder

Oct 28, 2008 | 1993 Honda Prelude

Not finding what you are looking for?
1992 Honda Prelude Logo

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...