Question about 2006 Chevrolet Silverado 1500 2WD

Open Question

Replace antenna 2006 Chevy Silverado 1500 - 2006 Chevrolet Silverado 1500 2WD

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
suterman
  • 158 Answers

SOURCE: thermostat location 2001 chevy silverado 1500

The thermostat is in the hose on the passener side of the waterpump.It is in the part that has the three 10mm bolts.Please rate my answer, Thank you.

Posted on Mar 05, 2009

Ad
DOODYDOODYDO
  • 105 Answers

SOURCE: process to change fuel pump on 2001 chevy silverado 1500

DROP THE FUEL TANK MAKE SURE YOU GO ABOUT HALF WAY THEN UNHOOK ALL THE LINES AND TERMINALS SO AS TO NOT DAMAGE THEM ALSO YOU NEED TO RELEASE THE FUEL PRESSURE AT FUEL RAIL BEFORE REMOVING ANY LINES

Posted on Jul 29, 2009

  • 73 Answers

SOURCE: how to replace spark plugs on 2005 chevy silverado

spark plug wrench and alot of patients with the very back ones hard to get to

Posted on Oct 02, 2009

  • 1608 Answers

SOURCE: 2006 5.3ltr chevy silverado z71 p0455 andp0449

These codes are for the evaporative emission system.The 455 is the vent solenoid.The 455 is a large leak in the evap.system.The vent solenoid I would replace because they go bad and will not work because they are under the vehicle in the rear of the truck.There is a bulletin for these and the vent valve is installed in another spot.The number for the bulletin is 02-06-04-037E.You should also look for a broken or loose hose or pipe that might have came off.Specially if you ran over something.If none found it could just be the vent solenoid stuck in the venting position.Good luck.

Posted on Dec 01, 2009

Molson02536
  • 3854 Answers

SOURCE: 1999 1500 Chevy Silverado - microchip for anti-theft?

Document ID# 803013
1999 Chevrolet Chevy K Silverado - 4WD

Security Lamp Illuminated on the IP, Engine Stalls, No Start, DTC B2960 (Security System Sensor Data Incorrect but Valid) Set (Inspect and Repair Cause of DTC B2960)
1999-2001 Chevrolet and GMC C/K Pickup and Utility Models (Silverado, Sierra, Tahoe, Suburban, Yukon, Yukon XL)

This bulletin is being revised to add information on inspecting for electrical intermittent conditions and important connector C201 tightening steps. Please discard Corporate Bulletin Number 01-08-56-002 (Section 08 -- Body and Accessories).

Condition
Some customers may comment on the following conditions. These symptoms may be intermittent.

• Security lamp illuminates while driving. The Security lamp may be On or Off when the customer brings the vehicle to the service facility.

• The engine cranks but will not start and the Security lamp is flashing.

• The engine starts then stalls and the Security lamp is flashing.

Cause
Condition(s) may be due to an incorrect Passlock™ sensor voltage received by the body control module (BCM) from the Passlock™ sensor due to the following conditions. Most intermittent conditions are caused by faulty electrical connections or wiring.

• A 7 ohm variation in the sensor ground circuit wiring, circuit 1057

• A 100 ohm variation in the Passlock™ sensor signal wiring circuit, circuit 1836

Inspect for the following items:

• Broken wiring inside the insulation.

• A poor connection between the male and female terminal at the connector. Refer to Testing for Proper Terminal Contact under Testing for Intermittent and Poor Connections in Wiring Systems for the specific procedure.

• A poor terminal to wire connection. Some conditions that fall under this description include poor crimps, poor solder joints, crimping over the wire insulation instead of the wire itself, and corrosion in the wire to terminal contact area.

• Wire insulation that is rubbed through. This causes an intermittent short as the bare area touches other wiring or parts of the vehicle.

• A poor connection between the male and female terminal at a connector. This poor connection may be the result of contamination or deformation.

- Contamination may be caused by the connector halves being improperly connected. A missing or damaged connector seal, damage to the connector itself, or exposing the terminals to moisture and dirt can also cause contamination. Contamination, usually in the underhood or underbody connectors, leads to terminal corrosion, causing an open circuit or intermittently open circuit.

• Separate the connector halves.

• Visually inspect the connector halves for contamination. Contamination may result in a white or green build-up within the connector body or between terminals. This causes high terminal resistance, intermittent contact, or an open circuit. An underhood or underbody connector that shows signs of contamination should be replaced in its entirety including the terminals, the seals, and the connector body.

- Deformation is caused by probing the mating side of a connector terminal without the proper adapter, improperly joining the connector halves, or repeatedly separating and joining the connector halves. Deformation, usually to the female terminal connector tang, can result in poor terminal contact causing an open or intermittently open circuit. Using an equivalent male terminal from the J 38125-B, test that the retention force is significantly different between an good terminal and a suspect terminal. Replace the female terminal in question.

Correction
Have any of the following components had service recently?

• The BCM

• The ignition lock cylinder case assembly

• The PCM/VCM

If any of the above components have been replaced, the Programming Theft Deterrent System Components procedure must be performed before any diagnostic procedures are performed.

To assist in diagnosis, the following steps are provided.

Does the engine start? If not, use the Engine Cranks but Does Not Run diagnostic information in the Engine Controls sub-section of the applicable Service Manual.
Important:

• The Security telltale on the message center is controlled by the vehicle theft deterrent (VTD) system and the content theft deterrent (CTD) system. The Security telltale is controlled by the BCM through the Class 2 data line.

• The VTD system portion of the BCM controls the Security telltale when the ignition switch is in the On position. The VTD system uses the Security telltale as a malfunction indicator.

• The CTD system portion of the BCM controls the Security telltale when the ignition switch is in the Off position. The CTD system uses the Security telltale to identify system status.


Observe the Security indicator lamp in the instrument panel.
Remove the key from the lock cylinder.
- Security indicator should be Flashing when the door is open.

- Security indicator should be Off when all the doors are closed.

- If the Security indicator does not come On or go Off correctly, refer to the Content Theft Deterrent System diagnostic and repair information in the applicable Service Manual.

With the Doors closed, place the key in the lock cylinder and turn to the Run position. Observe the Security indicator lamp.
- Lamp is On and does not go Off however, the engine starts. This indicates that the VTD system detected a fault when the engine was running.

- Lamp flashes On and Off. This indicates a problem has been detected by the VTD (Passlock™) system and the engine may not start this key cycle, a current condition.

Important: You must diagnose the diagnostic trouble codes (DTCs) in the order specified in the DTC table shown below. Failure to do so may result in one or more of the following conditions:


• Extended diagnostic time

• Incorrect diagnosis

• Incorrect parts replacement


DTC
Diagnostic Procedure
Module

Important: Before you use this table, diagnose P0601, P0602, P0604, and P0606. Refer to Diagnostic System Check - Theft Deterrent.

PXXXX Other PCM DTCs

Refer to the following procedures:

• Diagnostic System Check - Engine Controls in Engine Controls - 4.3L

• Diagnostic System Check - Engine Controls in Engine Controls - 4.8L, 5.3L, 6.0

• DTC P0192 in Engine Controls - 6.6L

• Diagnostic System Check - Engine Controls in Engine Controls - 8.1L


If none of the above items are true, proceed with the following steps:

Install seat covers.
Connect the scan tool to the diagnostic link connector (DLC).
Enter scan tool diagnostics.
Select the model year of the vehicle.
Select light truck.
Select F1, (Body).
Select "C" or "K" for Series.
Select F0, Body Control Module.
Select F0, (Diagnostic Trouble Codes (DTC)).
Select F0, (DTC information).
Select F0, (Current DTC).
Record on the repair order any current DTCs displayed. If none, skip the next step.
Is a current B2960 DTC displayed? If no, the condition is not present with this key cycle. Continue to the next step.
Select Exit.
Select F1, (History DTC).
Are any history DTCs other than B2960 present? If so, diagnose those DTCs first using the appropriate service information, otherwise continue.
Select Exit.
Select Exit.
Select F1, Data Display.
Select F6, Security.
Cycle the key to the OFF position and wait 20 seconds.
Slowly turn the key to the RUN position. Be careful not to turn the key into the START position.
Observe the following values:
- Passlock™ Data Voltage should be 5.0 volts.

- Passlock™ State should be Normal.

- Passlock™ Code should be Open.

Rotate the key to the START position, and observe the following again:
- Passlock™ Data Voltage should be less than 5.0 volts. Passlock™ Data Voltage should remain steady and not fluctuate. The test vehicle used for this diagnostic procedure had a voltage value of 2.49 volts. The vehicle being worked on may be either higher or lower than this value. The key is that it has to be less than 5.0 volts.

- Passlock™ State should be "Monitor Passlock™".

- Passlock™ Code should be Valid Code.

If no trouble is found and the customer has experienced one of the symptoms or the code is a history DTC, the most likely cause is the VTD (Passlock™) wiring, specifically the wires from the VTD (Passlock™) sensor to the BCM.

Posted on May 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2006 Chevy Silverado 1500 extended cab heater won't shut off when I turn heater off and when truck isn't started and still stays on


Sounds like the HIGH fan relay is stuck in the ON position. Pull the relay and see if it goes off. It should. Then simply replace the relay. This relay should be located under the hood, in the black relay/fuse center.

Mar 29, 2016 | 2006 Chevrolet Silverado 1500

2 Answers

Blower motor does not turn off i have to take the fuse out


Go online to and google" manuel for 2006 chevy silverado 1500 2wd". Or you can go to ask.com and ask" Where is the resister located on a 2006 Chevy Silverado 1500 2wd". It will give you the info you need.

Dec 13, 2012 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

2006 chevy silverado front brake caliper, how to replace seal kit


Your better off just replaceing the whole unit. The rebuildsa never last very long and the calipers are only like $30-$40 at Autozone

Mar 08, 2010 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

2006 5.3ltr chevy silverado z71 p0455 andp0449


These codes are for the evaporative emission system.The 455 is the vent solenoid.The 455 is a large leak in the evap.system.The vent solenoid I would replace because they go bad and will not work because they are under the vehicle in the rear of the truck.There is a bulletin for these and the vent valve is installed in another spot.The number for the bulletin is 02-06-04-037E.You should also look for a broken or loose hose or pipe that might have came off.Specially if you ran over something.If none found it could just be the vent solenoid stuck in the venting position.Good luck.

Nov 30, 2009 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

How do I replace the rh fender on 2000 chevy silverado 1500?


1.- remove the hhod and hood hinge
2.- loosen the wheel lug nuts , raise the vehicle and securely support on jackstands, apply parking brake .remove the fron wheel.
3.-Disconet the antenna( fender only)
4.- Remove fender mounting bolts at fron close to the turn signal.
5.-remove the top view bolts at the engine comparment.
6.-Detach the fender is a good idea to have an assistant to prevent damage to the parts of the body
7.- Installation is the reverse of removal.

Jun 20, 2009 | 2000 Chevrolet Silverado 1500

2 Answers

Change Fuel Filter on 1999 Chevrolet Silverado 1500


It's on the driver side frame. It's not hard to install one. Just have to have a special tool to get the line off the filter.

Jan 08, 2009 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...