Question about 1994 Ford Mustang

1 Answer

How do i install the ford racing hood pins on my 94 mustang gt?? can ya help me. i need to know where to bolt the longer screw were the pin go

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 17,970 Answers

I suggest visit this links:
- Link 1
- Link 2
- Link 3

Hope help with this.

Posted on May 25, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ive got a 94 mustangGT and ive got an SCT flash programer the OBD II port is not working ? Ive checked all fuzes


Check all the pins in the socket. My 03 gt had a bent pin in the socket and my tuner wouldn't work. Make sure the connector on the scanner programmer is in good shape. Hope this is helpful, Good luck.

Feb 16, 2015 | 1994 Ford Mustang

1 Answer

Cant get caliper pins out on 1995 ford mustang to replace brake pads seems stuck


I would get a small propane or mapp gas torch and heat the area of the bracket where the pin is. A bench vise or a pair of vice grips will aid in twisting the pin out. You might have to replace the pin and the rubber boots....Good Luck

Nov 20, 2012 | 1995 Ford Mustang GT

1 Answer

I need timing belt digrams for a 94 ford probe gt has a 6 cylindar engine


moz-screenshot-1.pngAlign the engine timing marks as follows, then install the belt.

ae00695.gif

f446780.gif
Once the belt is routed, as shown below, install the indicated pulley last, then pull the pin out of the hydrualic-tensioner.
cc4ecb7.gif

May 20, 2010 | 1994 Ford Probe

3 Answers

Can i replace a tie rod {inner} on a 94 ford mustang , drivers side without taking off rack and pinion. I need to get a roll pin off the inner tie rod and thats the problem it looks pressed in not set...


Real simple, assuming you know how to take the outer tie rods off. You have to take the clip that holds the plastic boot on off, then slide back the plastic boot, and you'll be able to unscrew the whole inner tie rod assembly. The hardest part of the whole process is installing the new ones to the exact settings of the old ones

Mar 13, 2010 | 1994 Ford Mustang

1 Answer

Putting a 302 in a 99 mustang


You'll need the K-member from a 94'-95' v6 or GT, along with the correct motor mounts. once you have that it should drop right in. But there are many more parts you'll need to make it work like a 5.0 tranny, exhaust, wiring, pcm, radiator, and maybe more. Look in the Ford Racing catalog and drop a 4.6L Cobra motor in there. A lot fewer parts to buy. Also if your state has car inspections the 5.0 is not OBDII, and should only be attempted if its going to be a "race only" car.

Jan 08, 2010 | 1999 Ford Mustang Cobra

1 Answer

I need to see the parts for the front disc brakes so i know what the parti need is called it is the part that holds the caliper firm


ASSUMING A MUSTANG GT NOT THE FORD GT EXOTIC 5.4 SUPERCHARGED ONE. IF THE ONE YOU HAVE IS A GT MUSTANG IT IS A CALIPER SLIDE PIN AND BOOT. YOU CAN GET A CALIPER PIN SET OR HARDWARE KIT AT THE DEALERSHIP. OT HAS THE BOOTS AND PINS AND 14MM BOLTS TO SECURE CALIPER TO PIN FOR BRACKET RETAINMENT. MAKE SURE YOU PUT GREASE IN HOLES FOR PINS OR THEY MAY SEIZE UP AND WEAR ONE PAD DOWN.

Jul 12, 2009 | Ford GT Cars & Trucks

1 Answer

Rear Axel Seal


Wheel, brakes etc that are in way of pulling axle out have to come off. Drain rear end fluid, remove rear housing cover, remove bolt that holds pin in differential, remove differential pin, push in slightly on axle to remove "U" clip that holds shaft in, then slide shaft out. replace seal. Reverse procedure for re-install & fill with gear lube. If any questions, get back to us.

Apr 16, 2009 | 2002 Ford Mustang

1 Answer

Any tricks to know before i start replaceing air pump on my 94 mustang gt


loosen air pump pulley bolts first..then take off belt...you will be able to get to the front top bolt that way..the bottom bolt u get from the back..i think it is a 13mm..steedi makes a delete kit for it also which retains factory belt size..

Feb 19, 2009 | 1994 Ford Mustang

1 Answer

Installing pin on hood on '93 mustang


if the spot under the hood is flat then u can slightly enlarge the holes for the hood plates and even the they will be at an angle the pins will still be straight and will still fit my 78 z28 track car was the same way the whole hood is contoured and it worked great

May 22, 2008 | 1993 Ford Mustang

Not finding what you are looking for?
1994 Ford Mustang Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...