Question about 2000 Lincoln LS

1 Answer

My horn is not working. It went from working

My horn is not working. It went from working every now and then to nothing. What do I do?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Lincoln Master
  • 3,433 Answers

Have the horn relay either tested or replaced. Intrermitant then fail indicates this may very well be the problem. Disconnect the horn itself and have someone press horn button. Listen for clicking of relay. If clicking,locate the rrelay. . If no vlivkicking, ther is your problem. Now to locate the relay. Should be under the hood on firewall. Good Luck

Posted on May 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The horn on my 1999 ford f250 keeps going off by itself.


Likely the relay is stuck. The horn gets 12v when you press the horn button and it energizes the relay to send power to the horn. The horn gets 12v and sends that through the horn and then to ground. There's nothing in the horn to cause it to stay on. The only other possible cause would be a horn button that is stuck in a depressed position or the wire is damaged and is grounded. Any relay you have that has the same dimensions can be used to test if the relay went bad by swapping it out and seeing if the horn blows.

Jan 13, 2014 | Cars & Trucks

1 Answer

Horn went off and wouldnt stop


the horn is made up of 2 metal plates with foam in between and that foam dissolves to nothing over time so that the metal plates touch witch sets off the horn all i did was cut a peace out of an old seat cushen and made it up myself its that easy

Nov 27, 2013 | Nissan Cars & Trucks

1 Answer

I parked my vehicle, went into a store, came out and the horn was stuck on. I popped the hood, to see if there was anything wrong with the horn. Nothing wrong, so I got in the car and pushed on the horn a...


the wires are touching inside the horn you must take it apart and put some electrical tape to the wires that are touching and your problem should be fixed.

Aug 21, 2013 | 1998 Honda Passport

1 Answer

The horn on my sequoia randomly went off,no one was driving it it was just parked in the drive way. I had to unplug the horn.


Could be a motion sensor is going bad (sensors that detect someone breaking in). See if you dealer can verify they are OK.

Dec 24, 2012 | 2002 Toyota Sequoia

1 Answer

My horn stopped working on my 2001 oldsmobile silhouette. It made a funny noise before it went out. We changed the relay but that didn't do the trick. Any ideas?


The horn itself is dead , that funny noise was it's last breath. You can get a horn from an auto wrecker for just about nothing. It does not necesarilly have to be from the same vehicle , as long as it fits.

Feb 10, 2011 | 2001 Oldsmobile Silhouette

1 Answer

2006 Jeep grand cherokee horn going off


You need to reset your alarm system and the only way I know how to do that is to disconnect the battery and reconnect it.

Jul 13, 2010 | 2006 Jeep Grand Cherokee

1 Answer

I just bought the car actually, got in it and went...


best bet will be to grab a test light and run it over every fuse you can find.

May 14, 2010 | Cars & Trucks

1 Answer

Horn and cruise control stopped working


The horn probably got water in it and this caused it to rust around the electro-magnet inside causing it to seize up. Replace the horn.

Jul 29, 2009 | Mazda MAZDA6 Cars & Trucks

Not finding what you are looking for?
2000 Lincoln LS Logo

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

fordexpert

Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...