How do I replace the front wheel bearings on a

There are a number of videos...
For RWD front hubs. (F250 will just have larger bolts.)

How To Install Replace Front Wheel Bearing Hub Assembly 2004-08 Ford F150
For 4x4 front hubs.

Ford Super Duty hub bearing replacement Driver side

Install front wheel bearing hub assembly on a ... - YouTube

? 8:42
https://www.youtube.com/watch?v=LQ-DGdt2J2U
Mar 11, 2014 - Uploaded by Andy Taylor
... Install front wheel bearing hub assembly on a 2003-2014Toyota 4Runner .... Pressing a 2005 and up Toyota Tacoma,4Runner, FJ Cruiser 2WD or 4WD ... How to Remove & Replace a Toyota 4x4 Manual Locking Hub ...
images for 99 Toyota 4 runner 2 wd front wheel removal

These video might ive you some idea:


How to Replace Front Wheel Bearing


Replace Front Wheel Bearing Hub Ford Taurus Mercury Sable


How To Install Replace Front Wheel Hub Bearing Taurus Sable 96 06 Part 1...


How To Install Front Wheel Bearing Hub Assembly 2002 05 Ford Explorer...

Hi...your problem might be coming from your front wheel bearing hubs. They are know to cause this problem as they wear out and eventually have to be replaced.

http://www.autozone.com/autozone/parts/2006-Chevrolet-Silverado-3500-4WD/Wheel-Bearing-Hub-Assembly-Front/_/N-jnpe7Z8kns

If I helped...please rate me...thanks!

If you're talking about the front wheel bearings, they can't be serviced. They can only be replaced. They are sealed for life (even if the life seems to be a little short).
Here's the front bearing:


I never replaced the rear bearings on my 2002 Escape 4X4, but here's a picture of the rear hub.

Those vehicles should have a hub assembly which incorporates a bearing and hub in one unit. To my knowledge the bearing is not serviceable. The hub assembly is bolted to the steering knuckle, so there actually is no wheel bearing torque. The tire/wheel assembly bolts directly to the wheel flange on the new hub assembly.

There are issues with the 4x4 system I.w.e ends ingesting moisture/water into vacuum actuation system causing no 4x4 or ratcheting outboard I.w.e ends. (Even if you don't go 4x4'n ) pull off vacuum hoses @ I.w.e ends and check for moisture/water/rust also the I.w.e is not part of the wheel bearing itself It is the part on the axle side (inboard) of the spindle. (EVEN DEALERS CAT LISTED WRONG)Many shops just replace the wheel bearing side this may fix the symptom but not the true cause of damaged I.w.e. ! Check with a reputable dealer they should have info on this condition and repair procedure.


The integrated wheel end (IWE) system contains the following:

Vacuum reservoir
IWE solenoid
IWEs (spring loaded vacuum hubs)
Vacuum hoses
Check valve
The IWE system uses vacuum hubs that engage the front wheel hubs to the front half shafts or disengage the front wheel hubs from the front half shafts.

The IWE solenoid receives engine vacuum from the vacuum reservoir.

When the 4-wheel drive system is in 2WD mode, the 4x4 module (PCM)supplies a ground path to the IWE solenoid to apply vacuum to the integrated wheel ends (disengaging the front hubs from the front half-shafts). In 4WD mode, the 4x4 module (PCM) does not supply the ground path to the IWE solenoid, vacuum is not applied to the integrated wheel ends and an internal spring keeps the front hubs engaged to the front half-shafts.

The 4 Bolts that Hold the HUB in Also Hold the Backing Plate
Hub Replacement - Rear (Front Wheel Drive/Drum)

Removal Procedure

1. Raise and support the vehicle.
2. Remove the tire and wheel.
3. Remove the brake drum.
   1. Remove and DISCARD the wheel bearing/hub bolts.
   2. Remove the wheel bearing/hub.
   3. Disconnect the wheel speed sensor electrical connector (2).Installation Procedure
   4. Connect the wheel speed sensor electrical connector (2).
      1. Install the wheel bearing/hub. Caution: These fasteners MUST be replaced with new fasteners anytime they become loose or are removed. Failure to replace these fasteners after they become loose or are removed may cause loss of vehicle control and personal injury. Notice: Refer to Fastener Notice in Service Precautions.
      2. Install the NEW wheel bearing/hub bolts.
      • Tighten the NEW wheel bearing/hub bolts to 80 Nm (59 lb ft) .
      1. Install the brake drum.
      2. Install the tire and wheel.
      3. Lower the vehicle.

Plan on spending more than $75 on this repair I am quite shore that that wont evan cover the parts. It definitely has a wheel bearing in the case of this vehicle it can only be replaced as an assembly that includes the hub. The ABS wheel speed senser is often sold as part of the assembly or in some cases is sold separately. good chance it will need to be replaced. Get the job done as soon as possible this is a very unsafe condition Your wheel will fall off while driving eventually if not repaired

hi have a look here
Suzuki Workshop Manuals

please rate my answer if useful