Question about Hyundai Motor S

Open Question

How to remove starter motor on a hyundai matrix 1.5td

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2003 hyundai elantra starter removal where are bolts located on the starter


It's bolted to the outer edge of your transmission. If it's a front wheel drive, it may be near the front of the motor, where the engine and motor connect. Should only have two bolts holding it on. Hope this helps!

Oct 02, 2017 | Hyundai Cars & Trucks

1 Answer

How do I disconnect starter in 2008 Hyundai Veracruz


Here is the procedure from Autozone.com
Removal & Installation Specific to:
Hyundai Santa Fe 2006-2008
Hyundai Veracruz 2007-2008
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable and wait at least 3 minutes, Speedometer cable and shift cable from the transaxle, Starter motor wiring, Starter motor bolts, and the starter
To install:
Installation is the reverse of removal. Tighten starter motor bolts to 20-25 ft. lbs. (27-34 Nm).

Jul 24, 2017 | Hyundai Cars & Trucks

1 Answer

My Hyundai matrix can't start power is out of the fuel pump line, this happened after changing the front shaft and all fuse are OK. Please help.


Check your Starter.

You may have disconnected while working front shaft.

Run a Black Cable from Negative of Battery to Negative of Starter.
Then Red Cable from Positive of Battery to Positive of Starter.
Be very careful when doing this, the Starter will turn as soon as you make contact.

It's best to use a DVM to measure contacts.

Aug 19, 2016 | Hyundai Matrix Cars & Trucks

1 Answer

Locating, removing and replacing starter motor on a 2000 hyundai sonata v6 (2.5 or 2.7 I believe) automatic


The starter is located below the exhaust manifold on the LH side of the engine (side facing the radiator). It is held in place by two 14mm bolts on the transmission side. Be sure to disconnect the battery before you attempt to remove the starter.


ghost45_43.jpg

Aug 31, 2011 | Hyundai Sonata Cars & Trucks

1 Answer

How to replace starter



Removal & Installation



0996b43f8022cbd5.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Starter mounting-Matrix
Starter mounting-Matrix

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Negative battery cable Right side engine undercover Starter wiring Starter
  3. Installation is the reverse of removal. Torque the bolts to 27 ft. lbs. (37 Nm) and the nut to 7 ft. lbs. (10 Nm).



0996b43f8022cbd5.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Starter mounting-Matrix
Starter mounting-Matrix

  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:

    Negative battery cable Right side engine undercover Starter wiring Starter
  3. Installation is the reverse of removal. Torque the bolts to 27 ft. lbs. (37 Nm) and the nut to 7 ft. lbs. (10 Nm).

Jan 14, 2011 | Toyota Matrix Cars & Trucks

1 Answer

Where is my starter and how do I change my starter?


2000 Hyundai Elantra 2.0L MFI DOHC 4cylRemoval & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Speedometer and shift control cables Starter electrical connectors Starter motor
  3. 2e15922.jpg

    Fig. Exploded view of the starter-XG 300 and XG 350

To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 25 ft. lbs. (34 Nm) Starter electrical connectors Speedometer and shift control cables Negative battery cable
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Air intake assembly Speedometer cable Shift cable Starter wiring connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 20-25 ft. lbs. (26-33 Nm) Starter wiring connectors and torque the battery cable nut to 88-140 inch lbs. (10-16 Nm) Shift cable Speedometer cable Air intake assembly Negative battery cable
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Air intake assembly Speedometer cable Shift cable Starter wiring connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 20-25 ft. lbs. (26-33 Nm) Starter wiring connectors and torque the battery cable nut to 88-140 inch lbs. (10-16 Nm) Shift cable Speedometer cable Air intake assembly Negative battery cable
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Speedometer and shift control cables Starter electrical connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 25 ft. lbs. (34 Nm) Starter electrical connectors Speedometer and shift control cables Negative battery cable.

All Others
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable and wait at least 3 minutes Speedometer cable and shift cable from the transaxle Starter motor wiring Starter motor bolts and the starter
To install:
  1. Installation is the reverse of removal. Tighten motor retainers to 20-25 ft. lbs. (27-34 Nm).

Hope helps (remember rated this).

Jul 14, 2010 | 2000 Hyundai Elantra

1 Answer

Can't find the starter on my 2003 xg350 hyundai. can anyone help me?


hi from uk to locate starter motor just follow the positive/red cable that fits to battery positive post to the other end of this cable it will lead you to the starter motorsolenoid and starter itself if you intend workingon/removing starter etc ?? you must 1st disconnect the battery earth connection lead make sure you know radio code b4 disconnecting battery ? if you are having problem with starter ?? why not give symptoms on this board we may be able to advise b4 you spend unnecessary $$$ s ??

Jan 29, 2010 | Hyundai Motor 2003 XG350

1 Answer

Burnt out starter, how do i replace it


To Remove:
  1. Disconnect the battery ground cable.
  2. Remove the speedometer cable and the shift cable.
  3. Disconnect the starter motor connector and terminal.
  4. Remove the starter motor assembly.
To Install:
  1. Install the starter motor assembly.
  2. Connect the starter motor connector and terminal.
  3. Install the speedometer cable and the shift cable.
  4. Connect the battery ground cable.
5674741.jpg

Oct 01, 2009 | Hyundai Motor 1996 Elantra

1 Answer

1999 hyundai elantra starting problems


remove the starter motor and check for damage/wear on the teeth of the starter motor and the ring gear teeth on the flywheel.turn the engine by hand while checking the ring gear so as to check the condition all the way around.hope this helps

Aug 27, 2008 | Hyundai Motor 1999 Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

320 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...