Question about 2008 Chevrolet Uplander

Open Question

How do you remove the rear bumper cover on a 2008 Chevrolet Uplander LT with parking sensors?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

MNfisherman
  • 11896 Answers

SOURCE: how to remove the rear bumper cover on a town and

From underneath the vehicle. The bumper is held on by 4 bolts and nuts. (2 on each end) Remove the nuts and bumper will pull off. Then you can pry off bumper cover to once entire bumper is off.

Posted on Nov 23, 2009

chiquititas
  • 1010 Answers

SOURCE: 2006 Chevrolet Uplander LT 2wd bad road noise in the rear end

Seems like you have a bad DEALER. Because dealers are factory trained and have access to the latest bulletins and prelim information (THAT ISN"T AVAIL ANYWHERE ELSE). If they can't fix a problem or verify it, they have the ability to call GM engineering and speak with an engineer about the problem and get advice where to look. Coming online and saying that you have a noise from the rear while driving could be a hundred different things. GO to the GM Dealer, take a test drive WITH a technician. Its a 2006 its under warranty, and it is THEIR job to find the problem. If you aren't satisfied with the dealer, call customer assistance. Once customer assistance contacts them im sure you will get alot more help.

Posted on May 15, 2008

  • 99 Answers

SOURCE: Remove rear plastic bumper cover

please email me at meanness628@aim.com with any other info or questions if you have already gone to a body shop

Posted on Sep 29, 2008

  • 10 Answers

SOURCE: I need to remove the front headrest of a 2008 chevy cobalt lt

Push the button and pull up on it at the same time

Posted on May 25, 2009

  • 1 Answer

SOURCE: 2007 Chevrolet Uplander LT ABS and TC light on

We were having this problem...have your wheel bearing checked out. There was a sensor in the drivers side wheel bearing...once we replaced it (because it was going out) the ABS and Traction Control warning lights stopped coming on.

Posted on Jul 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing rear bumper cover for 2007 uplander


Lift the tail gate. There are clips or screws along the top edge. Remove this. The clips all you do is pull the center pin with a panel tool or pliers then the rest will come out. Then you will need to remove the clips holding the rear side of each of the back wheel wells in. Under that will be more clips, screws or bolts that hold the side edges of the bumper cover on.

Aug 19, 2016 | 2007 Chevrolet Uplander

1 Answer

Where is the ambient temperature sensor located?


GM typically puts ambient air sensors on the passengers side, under the headlight behind the bumper, or sometimes in the center behind the bumper attached to the hood release support bracket

Jan 25, 2016 | 2008 Chevrolet Chevrolet HHR LT

1 Answer

How do I replace rear parking sensor


You have to take bumper cover off .
Remove rear bumper fascia. Refer to Rear Bumper Fascia Replacement . Disconnect electrical from the rear object sensor. Lift the locking tabs on the housing and remove the rear object sensor.
Preliminary Procedure
  1. Remove the compartment sill plate. Refer to Rear Compartment Sill Trim Plate Replacement .
  2. Remove rear wheel liners. Refer to Rear Wheelhouse Panel Liner Replacement .
1
Rear Fascia Push Pin Retainers (Qty: 2)
2
Rear Fascia Nuts (Qty: 4)
Tighten
10 N?·m (89 lb in)
3
Rear Fascia Bolts (Qty: 2)
4
Rear Fascia Bolts (Qty: 6)
5
Rear Fascia
Tip
?€¢
Energy absorber and fascia are removed together. Cannot be separate on vehicle.


?€¢
Disconnect the electrical connectors.

Dec 22, 2015 | 2006 Cadillac DTS

2 Answers

2008 ford escape. removal of rear bumper cover


Pop the Hatchback open and remove the connectors
from the top of the bumper cover.

Optional Step: Using a Floor Jack, raise both sides
of the car in the back, supporting both sides with
jack stands, and remove the rear wheels.

Using Torx Bits, remove the inner rear wheel well
lining.

Get behind the rear wheel well and loosen the bolts
holding the bumper brackets on. They're pretty
difficult to find and remove. Be Patient. Do the
same to the other side.

Remove the rear bumper cover by pulling the cover
outward from the part nearest the wheel on both
sides. Once removed, take off the 2 black mounting
brackets from the bumper cover.

Good Luck

Feb 27, 2015 | 2008 Ford Escape

1 Answer

Where is the rear heater motor located on 2008 uplander


If the van has E59 on the RPO sticker you have to remove the left rear lower trim panel to access the motor. If it does not have E59 just remove the left rear compartment lid and compartment to access the motor. RPO E59 is a power left sliding door.

Sep 24, 2014 | 2008 Chevrolet Uplander

1 Answer

How do you remove the rear bumper on a chrysler 300c touring .I need to replace the rear parking sensors and this appears to be the only way


fsm covers this.
most cars are skins off , reveals all else.
bummper skins are the parts not made of steel.

Jul 06, 2014 | 2008 Chrysler 300C 2.7

1 Answer

Need to replace turn lamp on left front (dash message). I have replaced rear turn lamps, but cannot see how to access the turn lamp area in the front. In the rear a couple of bolts held the whole rear lamp...


Welcome to FixYa.com

Park and Turn Signal and Daytime Running Lamp Nuts (Qty: 3)

Tip

Disconnect the forward lamp harness connector from the lamp socket



leedavidian_239.jpg


Thank you for using FixYa.com

Regards, Lee Davidian

Jan 12, 2011 | 2006 Chevrolet Uplander

1 Answer

2008 chevolet uplander parking brake ajustment


if you have rear disc it's adjusted by ratching the rear,so if you have a pull up parking brake pull up and down 3 quick times,if it's on the floor press down and up three quick times.










TIM.....








Oct 25, 2010 | 2008 Chevrolet Uplander

2 Answers

I have a 2006 Ford Explorer and 2 of my park aid assist sensor are bad. They are in the rear bumper. How would i replace the sensors? Is it really necessary to remove the bumper?


You only need to remove the bumper cover. Remove both tail lamp assemblies. Under the tail lamps you will a 10mm and a 8mm bolt, remove these. Look into each rear wheel well rearward and you will find a T20 torx screw on both sides, remove these. On the top of the rear bumper, between the bumper and the bottom of the liftgate opening you will find 6 to 8 plastic rivets that can be removed by pulling the center pins out, remove these. At this point you should be able to lift upward and rearward and release the bumper cover. Once the cover is free you must disconnect the electrical connector to the sensor wiring harness. With the bumper cover on the ground or a bench, you will see 4 9/16" nuts that hold the styrofoam bumper cushion to the bumper cover, remove these. Now you should be at the point where the backup sensors are accessable. When you install the new sensors be sure your electrical connectors click when they connect. these connectors go on hard and if they don't click you will be doing this job again. Reassemble in reverse order.
Hope this helps

Apr 01, 2010 | 2006 Ford Explorer

1 Answer

How do you remove the spare tire from a 2006 chevy uplander?


To remove the spare you need to access tools stored in the back of the vehicle, passenger side storage area. Open llftgate, remove net (if equipped), lift tab and remove cover to tool storage. Attach folding wrench to extension, insert 'chisel' end on an angle through the hole in the rear bumper and into the hoist shaft. Turn wrench counter-clockwise to lower spare enough so you can pull it from beneath the van to detach. Good luck!

Aug 26, 2009 | 2008 Chevrolet Uplander

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

389 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...