Question about 2000 Oldsmobile Intrigue

1 Answer

I have to replace the ignition switch. Do I have

I have to replace the ignition switch. Do I have to remove the dash to get behind the key cylinder?

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

joshnaz
  • 186 Answers

SOURCE: key ignition switch needs replaced lock cylinder

disconnect the battery and pull the air bag fuse out to diable the air bag. Remove the steering coulmb trim covers and expose the lock cylinder. If the lock cylinder can be turned and is functional then push in the bottom tab and turn the lock cylinder then pull the whole cylinder out. If the keys broke inside and the lock cylinder is not functional the bottom tab will need to be drilled out.
graphic.aspx?mod=reptiff&module_id=1&session_id=%7b812b1a44-e9f7-498d-9233-3843c35aa6d4%7d&image_guid=00010135&print_bw=0&

Posted on Feb 27, 2010

  • 91 Answers

SOURCE: I have to replace the ignition switch. Do I have

Check out http://99intrigue.shutterfly.com/ignitionswitch. You don't have to remove all of the dash, just the radio and instrument cluster. It's not a big deal - hardest part is getting off the park lock cable, but if you remove the dash center vents, it's a cakewalk.

Posted on Apr 06, 2010

  • 383 Answers

SOURCE: new ignition starter switch which

sounds like wrong part

Posted on Jun 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2007 Toyota Tacoma 2wheel drive and I lost the keys and steering wheel is locked how do I remove steering wheel and replace ignition


How to Replace the Ignition in a Toyota Truck

The two primary components in a Toyota truck's ignition system are the actual ignition switch and the lock cylinder, which work with the ignition key. On most current models of the Tundra and Sequoia, you won't need to completely disassemble the entire steering panelicon1.png to access the switch and cylinder. Keep in mind that the exact procedure can vary depending on the year and model of your Toyota truck.

Instructions
    • 1 Disconnect the truck battery's negative cable by loosening the cable's clamp nut and detaching the cable from the battery post. Set the cable aside somewhere where it can't accidentally touch the battery terminal.
    • 2 Remove the under-dash panel on the left side of the truck by removing its four retaining screws and pulling it off. Detach the hood release cable by lifting the lever, removing the screws and disengaging the cable from the lever handle.
3.
  • Remove the air duct that is below the steering columnicon1.png to access the ignition switch. Unplug the electrical connectors at the rear of the switch, remove the mounting screws with a screwdriver and detach the switch from the lock cylinder housing.
  • 4 Detach the illumination ring by pulling out the plastic pin on the side. Turn the lock cylinder into the Accessory position with the key and insert a small screwdriver into the hole at the bottom of the ignition switch casting. Press the release bottom with this screwdriver as you pull the lock cylinder straight out.
  • 5 Insert the replacement lock cylinder with its own key into the ignition switch casing. Make sure you insert it so the cylinder is in the Accessory position. Replace the illumination ring with its pin.
  • 6 Mount the replacement ignition switch on the housing with its mounting screws and connecticon1.png it to the electrical connectors.
  • 7 Re-install all other components--the air duct, under-dash panel and battery cable--in the reverse order of removal.


  • Read more: http://www.ehow.com/how_5916602_replace-ignition-toyota-truck.html#ixzz31Nptu1ew

    May 11, 2014 | Cars & Trucks

    1 Answer

    I have to replace the ignition switch. Do I have


    Check out http://99intrigue.shutterfly.com/ignitionswitch. You don't have to remove all of the dash, just the radio and instrument cluster. It's not a big deal - hardest part is getting off the park lock cable, but if you remove the dash center vents, it's a cakewalk.

    Mar 26, 2010 | 2000 Oldsmobile Intrigue

    2 Answers

    Ignition switch removal.


    The switch body is threaded on the rear-of-dash side, and there is a large nut which threads on to tighten the switch to the dash. There may also or instead be a large C-clip, E-clip, or wavy spring clip which fits into a slot on the back of the switch. Some models (like my 68 Tempest) even had a press-in roll pin that had to be removed. My 65 Chevelle had the nut and the C-clip. Unplug the wiring connector first, and then on the floor on your back look under the dash to find it and remove it. You may have to remove the instrument panel bezel from the dash frame (several screws) in order to see/reach the back of the switch.
    This is not one of the easiest interior electrical jobs to do, but they put it in, so it will come out, I always say.

    Feb 28, 2010 | Pontiac LeMans Cars & Trucks

    1 Answer

    How difficult is it to replace ignition cylinder lock. Cylinder was ripped out


    The ignition switch is usually mounted to the steering column and is operated by a linkage rod.
    NOTE On column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.
    f32-17gif.gif The ignition switch is operated by the key switch. Courtesy of Ford Motor Company. To replace the switch:
    • Remove the ignition switch wiring harness.
    • Unbolt it from its position.
    • Bolt the new switch into position.
    • Attach the witing harness.

    btn-back_to_top.gif

    Oct 27, 2009 | 1996 Pontiac Grand Am

    2 Answers

    I have 1999 lexus ls470 -- same problem -- ignition switch


    Its usually NOT the lock cylinder on the 470s, its usually the housing. The cylinder is on the dash and points towards the engine. Behind the plastic dash panel (once removed) you will see it in fact sticks in an aluminum tube that goes down 2 or 3 inches, then makes 2 turns, left to attatch to the steering column, and right to attatch to the actual ignition switch. The gear and rod assembly that the cylinder attatches to that allows it to rotate the switch usually shatters in the middle and the key starts freewheeling because there is no longer any attatchment to any of the gears or springs or click points that youd usually feel as the rotational resistance. UNFORTUNATELY this is not a 5 minute job (If it was, cars would be a breeze to steal!). Youll need at least a lock cylinder housing (dealer stock em, they break all the tyme), and IF your cylinder is undamaged, change the housing (it bolts to the steering column and extends from column towards center console area where the ignition SWITCH is actually located). If your cylinder is damaged or the housing is so shredded you cant remove the lock cylinder by normal means...then youll also need the cylinder...and it will have to be recoded to the vehicle so the anti theft will allow the new keys/cylinder to start the car. If your old cylinder and keys are intact, then transfer them to the new housing and car wont even know it happened and should start up and work as normal. Some can be removed intact, some cant...depends on how yours broke.

    Aug 24, 2009 | 2000 Lexus LX470

    1 Answer

    How do I replace ignition switch?


    turn off radio.first so you wont lose code.then disconnect negative battery.you also want to disable air bags. because you going to have to remove center instrument panel trim bezel.and the instrument cluster.remove 2 screws securing the ignition switch.then push switch in straight back to clear the mounting bracket.lift it out from behind the instrument panel.disconnect the ignition switch electrical connectors.and the ignition interlock cable.using the key turn the lock cylinder to run and press in the pin to release the cylinder.then with draw the cylinder with key.the cylinder must be removed even if only the switch portion is to be replaced.in order to remove the 2 wires connector.WARNING WAIT 20 MINUTES.AFTER DISCONNECTING BATTERY.TO WORK ON INSTRUMENT CLUSTER GIVE AIR BAGS TIME TO DISCHARGED ABOUT 20 MINUTES..IF YOU REPLACE IGNITION SWITCH AT HOME CAR MAY NOT CRANK.BECAUSE.YOUR NEW KEYS HAS TO BE PROGRAM TO CAR .BEFORE IT CRANK OR THE THEFT DETERRANT AND PCM. WILL NOT RECOGNIZE IT.NOT LET IT CRANK.

    Jul 02, 2009 | 2000 Pontiac Grand Am GT

    2 Answers

    96 ford windstar ignition probs


    the ignition switch is the electrical part behind the lock cylinder where the key goes in.

    Ignition Switch Lock Cylinder
    Lock Cylinder Functional
    Removal
    1. The following procedure applies to vehicles that have a functional ignition switch lock cylinder (11582) and keys. If the key numbers are known, the correct key can be made. Disconnect the battery ground cable (14301). For additional information, refer to Section 14-01 .
    1. Turn the ignition switch lock cylinder to the RUN position.
    1. Place a 3.17-mm (1/8-inch) diameter wire pin or small drift punch in the hole in the steering column shroud under the ignition switch lock cylinder. Depress the retaining pin while pulling out on the ignition switch lock cylinder to remove it from the housing of the steering column.
    Installation
    1. Install the ignition switch lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the ignition switch lock cylinder into the steering column housing. Make sure the ignition switch lock cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the retaining pin of the ignition switch lock cylinder to extend into the hole of the steering column.
    1. Using the key, rotate the ignition switch lock cylinder to make sure of correct mechanical operation in all positions.
    1. Connect the battery ground cable.
    -------------------------------------------------------------------------------------
    Ignition Switch Removal
    1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    1. Remove the upper steering column shroud (3530) by removing the four or five self-tapping screws. Remove key release lever (3F527) (if equipped).
    1. Remove lower steering column shroud.
    1. Disconnect the ignition switch electrical connector.
    1. Rotate ignition switch lock cylinder (11582) to the RUN position.
    1. Remove the two screws retaining ignition switch (11572).
    1. Disengage the ignition switch from the actuator.


    71f4c5f.gif


    Item Part Number Description 1 11572 Ignition Switch 2 — Ignition Switch Lock Cylinder Housing 3 — Slot in Lock/Column Assembly A — (Part of 11572) Pin B — Alignment Mark
    Installation
    NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

    1. Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
    1. Check to make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
    1. Install the ignition switch into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
    1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
    1. Connect electrical connector to ignition switch.
    1. Connect battery ground cable. Refer to Section 14-01 .
    1. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
    1. Install upper steering column shroud.
    1. Install the lower steering column shroud and key release lever (if equipped).

    Feb 27, 2009 | 1996 Ford Windstar

    1 Answer

    Car was stolen broke the ignition


    REMOVAL

    1. On models equipped with airbag, disarm airbag as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.
    2. On all models, disconnect battery ground cable.
    3. Remove ignition switch as described under STARTING AND CHARGING SYSTEMS/COMPONENT REPLACEMENT AND REPAIR PROCEDURES/IGNITION SWITCH.
    4. Remove key light case from lock body, if equipped.
    5. On 1989 Accord models, place ignition lock cylinder in the ACC position.
    6. On except 1989 Accord, place ignition lock in the I position.
    7. On all models, position suitable punch into hole on lock cylinder housing and depress pin, then remove lock cylinder from housing.
    INSTALLATION

    1. On 1989 Accord models, install ignition lock cylinder as follows:
      1. Place ignition lock cylinder in the LOCK position.
      2. Rotate key until it is almost at the ACC position, then insert lock cylinder until pin contacts housing.
      3. Rotate key to ACC position, then push pin in and insert lock cylinder into housing until pin clicks into place.
    1. On except 1989 Accord, install ignition lock cylinder as follows:
      1. Place ignition lock cylinder in the O position.
      2. Rotate key until it is almost at the I position, then insert lock cylinder until pin contacts housing.
      3. Rotate key to I position, then push pin in and insert lock cylinder into housing until pin clicks into place.
    1. Install ignition switch and connect battery ground cable.
    SRS wire harness is routed near the ignition switch.

    CAUTION:
    • All SRS electrical wiring harnesses are covered with yellow outer insulation.
    • Before disconnecting the SRS wire harness, install the short connector on the airbag.
    • Replace the entire affected SRS harness assembly if it has an open circuit or damaged wiring.
    IGNITION SWITCH
    1. Remove the steering wheel, then remove the steering column covers.
    2. Disconnect the 7-P connector from the under-dash fuse box.
    3. Insert the key and turn it to "0."
    4. Remove the 2 screws and replace the base of the switch.

    Feb 13, 2009 | 1992 Honda Accord

    3 Answers

    1998 toyota


    There is a pin that you have to push in on the bottom of the lock cylinder housing.It is recessed in a hole.You have to turn the key to acc or on to get it to push in.Once you push it in you can pull the key and lock cylinder out.

    Dec 01, 2008 | 1998 Toyota Camry

    2 Answers

    Ignition Switch


    Hello 85chevy,
    Thankyou for choosing FixYa.com my name is David this should help you with your problem
    Home > Product and How-To Information > Product and How-To Information: I > Product

    Ignition Switch grey_line.gif Inspect | Test | Replace The ignition switch is usually mounted to the steering column and is operated by a linkage rod.
    NOTE On column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible.
    On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.

    0900823d800500ef.gif

    The ignition switch is operated by the key switch. Courtesy of Ford Motor Company.
    To replace the switch:
    • Remove the ignition switch wiring harness.
    • Unbolt it from its position.
    • Bolt the new switch into position.
    • Attach the witing harness.

    upper_left.gif grey_line.gif upper_right.gif grey_line.gif Look for More Parts A B C D E F G H I
    J K L M N O P Q R
    S T U V W X Y Z grey_line.gif lower_left.gif grey_line.gif lower_right.gif Related Parts: grey_line.gif 0900823d8004b202.gif Lock - Ignition (Cylinder and Keys) Return to top.

    Nov 06, 2008 | 1985 Chevrolet El Camino

    Not finding what you are looking for?
    2000 Oldsmobile Intrigue Logo

    349 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Oldsmobile Experts

    yadayada
    yadayada

    Level 3 Expert

    75197 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7782 Answers

    Are you an Oldsmobile Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...