Question about 1995 Mercury Villager

1 Answer

Replace water pump v6

How do I replace the water pump on a V6 3.0 Mercury Villager engine!

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

I have posted this information here


http://groups.yahoo.com/group/villagerquest/

Posted on May 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the signs of my 1997 mercury villager water pump to go out


heat gauge indicate hi temp, coolant leaking on ground below engine, coolant over flow tank constanly low, noise coming from pump body

Oct 08, 2014 | Mercury Villager Cars & Trucks

1 Answer

My 1997 mercuery villinger is losing water somewere and the front windshield is getting steamy but the tempture gauge is not going up could it be my water pump


it could be the pump, it could also mean you have leaking hose or hose connection, it could also indicate you have stuck thermostat.

AT worst it could mean a head gasket of the engine is burst and coolant is getting into the piston areas.

Suggest you find problem before you damage engine! $$$$$

Oct 08, 2014 | 1997 Mercury Villager

1 Answer

Where is the location of my water pump for my mercury villager


It is on the front of the engine, under the timing cover. You will need to remove the four screws on the water pump pulley before you take the cover off. Here is a picture:

chuckster57_9.gif

Jan 15, 2011 | Mercury Villager Cars & Trucks

1 Answer

Replace water pump v6


1. Drain the coolant.
2. Loosen, (don't remove yet) the 4 bolts that hold the water pump pulley.
3. Remove the drivebelt. In order to remove the belt you need to put a wrench on the tensioner pulley to decrease the tension on the belt.
4. Now remove the 4 bolts loosened in step 2.
5. Disconnect the upper radiator hose from the water pump and disconnect the bypass hose from the top of the water pump.
6. Remove the drivebelt tensioner by removing the bolt in the center of it.
7. Remove the water pump bolts. There are 6mm and 8mm bolts, a total of 12 bolts. They are not all the same length. Be careful to note which bolts go in which holes.
8. After all bolts are removed sometimes the pump will require a little whack with a rubber mallet to unseat the gasket. Never pry between the pump and engine block.
9. Before installing the new pump, clean all the old gasket material from the engine block.
10. Use RTV sealant on both sides of the gasket for the new pump.
And............ the rest is just reversing the above except that you can fully tighten the pump pulley before putting the belt back on.
I hope this is helpful.

Mar 26, 2010 | 1995 Mercury Villager

1 Answer

2002 mercury villager water circulation problem, engine overheats when started. Thermostat has been replaced, but no help. Does not overheat when themostat completely removed. Could water pump be the...


Check the new thermostat by putting it in a pan of water and bringing it to a low boil. See that it opens. It is possible to get bad parts off the shelf.

Jan 15, 2010 | 2002 Mercury Villager

1 Answer

How do I change a water pump for a 1994 mercury villager???


drain coolant first,take off serpentine belt loose 6 bolts on water pump take off water pump clean well,put new gasket than install new pump

Jan 10, 2010 | 1994 Mercury Villager

3 Answers

Does the V6 3 liter engines in these vans have a timing chain on a belt


it should have a timing belt. most V8's and up have chains.

Oct 03, 2009 | 2000 Mercury Villager

2 Answers

Engine overheating


Assuming you have no loss of water invesigate the cooling fan operation.If you are losing water but cannot see signs of this then investigate your head gasket.

Mar 28, 2009 | 2001 Mercury Villager

Not finding what you are looking for?
1995 Mercury Villager Logo

Related Topics:

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

fordexpert

Level 3 Expert

5474 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...