Question about 2000 Nissan Xterra

Open Question

How to replace an oil pressure sensor switch on 2000 nissan xterra. Is this something that can be diy?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

dennymulford
  • 1055 Answers

SOURCE: oil pressure needle at H

sounds like an oil pressure sening unit un plug it whilf its running and see if the gauge goes too zero,if not then the prob is the gauge, the sending unit is only about 15.00 at auto zone and easy too put in

Posted on Jan 28, 2009

  • 1 Answer

SOURCE: knock sensor

You have to take the entire intake manifold off upper and lower. you will find it on the main block after you take the lower manifold off.

Posted on Jun 03, 2009

ZJLimited
  • 17970 Answers

SOURCE: Diagram available for 01 Nissan Xterra Knock Sensor location?

V6 3.3L The sensor is located underneath the air intake manifold on top of the engine block. This should take an experienced mechanic about 3-4 hours to replace.

9bd8ec7.jpg

Fig. Engine compartment component locations

Hope this help (remember rated this free help) Good luck.

Posted on Feb 08, 2010

  • 66 Answers

SOURCE: how to replace a knock sensor on a 2002 nissan

Unplug the electrical plug/connector from the base of sensor. You will have to take out bolt from the head of the sensor that threads into the cylinder head. Thats really it. Unplug - Unscrew - replace!

Posted on Dec 31, 2010

  • 1114 Answers

SOURCE: knock sensor 2000 nissan xterra V6, location of

Hello the sensor is located under your intake manifold you will need to remove the intake manifold to gain access to it here is photos of what and where your looking for thisregeetone_0.pngregeetone_21.jpg

Posted on Jan 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace oil pressure switch on a 2006 nissan xterra


It's located by oil filter,may have to remove filter to remove switch,may need a stubby(short) wrench to remove,may be able to turn tiresout to get to,it's a tight fit.Remove electrical connector,then get wrench and remove,then take to Autozone and match up with new one,here it is. Duralast Oil Pressure Switch PS561 2006 Nissan Datsun Xterra 2WD 6...

Jan 22, 2014 | 2006 Nissan Xterra

1 Answer

Replace crankshaft sensor on 2000 nissan xterra


the crankshaft position sensor is directly behind the driver side cylinders, about 8 inches or so to the left of the exhaust and up behind the head. its a grey clip

Nov 14, 2011 | 2000 Nissan Xterra

1 Answer

Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

Nov 14, 2011 | 2000 Nissan Xterra

1 Answer

Engine oil pressure gauge reads high


check your oil pressure sensor mounted on r/h side of engine behind the alternator. its a rounded lookin sensor with single connector. i would replace it.

Oct 02, 2011 | 2006 Nissan Xterra

1 Answer

The oil pressure light on my 2004 nissan xterra stays


if the switch has been repaced then u most likely really have an oil pressure problem, you will neded to hook up a test mechanical oil pressure guage and verify the actual pressure, I suspect you will end up replacing the oil pump, the inlet screen may be clogged with dirt or the pump is worn out or has a stuck pressure regualtor valve.

Sep 08, 2009 | 2000 Nissan Xterra

1 Answer

2000 Nissan Xterra Service Engine soon indicator is always on


The knock sensor is not a huge deal to replace and will not turn on the light. It should be dont though.

The crankshaft sensor is located directly between the engine and transmission. It is dead center at the bottom.

May 17, 2009 | 2000 Nissan Xterra

1 Answer

Oil pressure needle at H


sounds like an oil pressure sening unit un plug it whilf its running and see if the gauge goes too zero,if not then the prob is the gauge, the sending unit is only about 15.00 at auto zone and easy too put in

Jan 28, 2009 | 2005 Nissan Xterra

1 Answer

Xterra no oil pressure


inner timing cover y shaped oil gallery gaskets..make your own or order the complete cover..costs from nissan are 500 canadian for the cover and around 1500 total for the replacement.oil pressure goes back up immediately after the install..alot of work to replace a cheezy piece of paper...

Nov 04, 2008 | 2000 Nissan Xterra

Not finding what you are looking for?
2000 Nissan Xterra Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...