Question about 2003 Hyundai Tiburon

1 Answer

The left signal is on all the time not flashing and even without the keys the light still on someone told is the body control module

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Yes body control module is at fault .but check jack plugs to rear of bcm as water ingress from poor window seal can cause corroision to terminals

Posted on Mar 02, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 3500 sierra left signal causes all lights to flash


Well, you're dealing with a short. If the right turn signal only works the right side bulbs, you know you're issue must be in the switch. The only way left turn signal would light the right side, but the right signal would not light the left is if you added a diode, which I doubt is the case. So the switch itself is suspect. That or a wiring issue. If you just bought the truck, and this is an existing issue I'd suspect wiring. If it just started doing this I'd suspect the switch.


I would check to make sure someone didn't monkey with the wires and switch the left turn signal with the hazard lights or something (do your hazard lights happen to flash only the left turn signals?). If it has or had an aftermarket alarm you need to check their work and see what may be screwed up. Alarm systems often tap into the parking lights, which will look like all 4 turn signals, but are actually dimmer filaments. Flashing the parking lights would actually make your radio flash too, so I'm kind of leaning this way. Can't say for sure on limited information though.

Aug 16, 2016 | Cars & Trucks

Tip

How to set & cancel theft deterrent system or how to set & cancel security...


Theft deterrent system (on some models)

Theft deterrent system is designed to deter vehicle theft. The system flashes the turn signal lights and turns on the interior light or the signal lights only (depending on the model), and sounds security horn and vehicle horn when it detects abnormalities such as follows:

• Any door or hood is forcibly opened.
• The batter terminal is disconnected and then reconnected
• The system control is disconnected and then reconnected.
• Abnormal impact is detected when the impact sensor function is on.

The system flashes the turn signal lights and turns the interior light or the signal lights only (depending on the model), and sounds security horn and vehicle horn if someone attempts to damage or break into your car.

Setting the system

You can set the system with or without the impact sensor function. For details, see "Canceling the impact sensor" below.

1. Turn the ignition key to "LOCK" and remove it.
2. Have all passengers get out of the vehicle
3. Push the lock (set) switch on the wireless remote control key once. At this time, the turn signal lights flashes once and the security indicator light comes on.

The system is set after 30 seconds. At this time, the security indicator light start flashing slowly.

Once the system is set, you cannot start the engine until you cancel the system.

The system will not be set in the following cases.

• When any of the door is open; security horn sounds for 1 second, close the door and set the system again.
• When the hood is open; close the hood securely.

Canceling the Impact Sensor

The impact sensor can be cancelled to prevent false alarms from being triggered incase of the following conditions:

• When parked in the noisy area
• The vehicle body or glass is subjected to a strong impact from the (such as in highly pressurized car wash).
• When transporting by a car carrier or ferry.

To cancel the impact sensor;

1. Lock the door by pushing the lock (set) switch on the wireless remote control key once, and turn signal light flash once
2. Then push the lock (set) switch twice within 5 seconds. At this time, the turn signal flash 5 times to indicate the impact sensor function is disable.

The impact sensor is deactivated as long as the system remained armed.

Canceling the system

The system will be cancelled by the following two ways:

• Turn the ignition key from "LOCK" to "ON" position.
• Unlock any of the doors by pushing the unlock (cancel) switch

If the turn signal lights flash 3 times, the system has been alarmed. Check to see if there is any abnormality with your vehicle.

If any of the doors is not opened within 30 seconds, all doors will be automatically locked and the system will be set.

When the system is set

Activating the system; When the system detects abnormalities such as follows, it flashes the turn signal lights and turns on the interior light or the turn lights only (depending on the model) and sounds the security horn and vehicle horn of 30 seconds.

• Unlocking any door without using wireless control
• Any door or hood is forcibly opened.
• The battery terminal is disconnected and then reconnected.
• The system control assembly is disconnected and then reconnected
• Abnormal impact is detected when the impact sensor function is on.

Reactivating the alarm;

Once set, the system automatically resets the alarm after the alarm stops.

The alarm will activate again under the same circumstances described in "Activating the system".

Stopping the Alarm

The alarm will be stopped by the following two ways;

• Turn the ignition key from the "LOCK" to "ON" position.
• Unlock any of the doors by pushing the unlock (cancel) switch.

The system can be cancelled by these ways at the same time.

If the battery becomes discharged due to the vehicle being unused, for a long time etc., when the battery is recharged or replaced, the system will activate the alarm. If this happens, immediately unlock any of the doors by pushing the unlock (cancel) switch, and the alarm will stop.

Testing the system

1. Set the system
2. Insert a wireless remote control key into the key hole on the driver's door handle, and unlock the door.
3. Open the door, and an alarm will sound.
4. Stop the alarm by pushing the unlock (cancel) switch.
5. Repeat this operation for the front passenger's door.

Good luck.

on Nov 08, 2010 | Toyota Pickup Cars & Trucks

1 Answer

Help with learn mode.How to? sorry,it's a 2007 versa sl hatchback,not a sentra.


To activate a new transmitter in the tire pressure monitoring system WITHOUT the Nissan Consult scan tool: Under the dash above the OBD II connector is a single wire connector called the "tire pressure warning check connector". Use a jumper wire and ground the tire pressure warning check connector with the key OFF. Then turn the key ON and cycle the ground at the tire pressure warning check connector 5 times within 10 seconds of turning the key ON. This should cause the tire pressure monitor light to start flashing indicating the system is in "learn mode". Then use the activation tool starting at the left front tire and work around the vehicle in a clockwise direction - front left, front right, rear right and rear left. Activating each transmitter at each wheel should make the turn signal flash one time and after completing all 4 wheels, the turn signals should flash two times and all 4 time pressures should be displayed.

Apr 07, 2015 | 2007 Nissan Sentra 2.0 SL Sedan

2 Answers

2000 chevy 2500 (new style) parking lights wont shut off


The parking lights staying on and the left turn signal not working may not be related, the turn signal is probably a burned out bulb, turn on the left signal and see if all the bulbs light up if not replace the burnt one, if they all light, the turn signal flasher may be at fault ( it can work with one side and not the other), as far as the parking lights staying on, check the door "pin" switch that controls the interior lights (are the interior lights staying on too?), since the chimes are staying on even with the keys on , I would suspect the door pin switch, probably the drivers side. I believe there may be a timer on the parking lights that turn them off after several seconds after the door is closed, this may be at fault if not the pin switch. newer cars and trucks also leave the reverse lights on for a while after the door is closed.

Dec 20, 2013 | Chevrolet Silverado Cars & Trucks

1 Answer

When i push on the brake pedal, both (Left and Right) signal lights come on solid.


I assume when you state "signal lights" you are refering to the signal lights in the grill as well as in the tail lights?
Did someone do some wiring for a trailer hook up? (like maybe a U-Haul mechanic???) Even if there is a simple plug in adaptor that goes inline in the rear of the vehicle I have seen those go bad and do funny things. If there is a socket, wires may be shorted inside.

If not, is there any creative wiring inside. Someone install a radio and tap into the wrong wires or an alarm that flashes the lights?

Aug 31, 2011 | 1995 Chevrolet K1500

1 Answer

Speedometer works at will.Signal lights flash real fast.


You have a light bulb out. go through the motions with someone checking for fuction. brake left turn right turn reverse and running lights. Its going to be in one of your blinker bulbs so have someone check to make sure that all the bulbs that are suppose to be flashing are actually flashing when you turn them on. Keep in mind that you may have more than one or even two or three bulbs that should flash at any corner. A rapid flashing at the cluster means that you have a bulb out in the blinker curcuit. Happy hunting. For bulbs not eggs...Hope this helped...

Jul 14, 2011 | 2005 Kia Spectra

1 Answer

I have a 2001 Pontiac Firebird. When i start my car, my left turn signal light comes on but the right front turn signal light remains off. If i turn my lights on, the right turn signal light then comes...


Perhaps a dicky connection somewhere. Perhaps corrosion, even moisture in the connection plugs. Inspect all connections to your indicator lights. Also check for worn or damaged wires. Also Have a look inside the lenses of the lights to see if the the globes are corroded or have water ingress etc and causing shorts to other wiring within the lighting circuits.

You may also consider turn indicator lever to on to indicate truniong right, make sure the engine off. Have someone watch right indicator and literally grab the plugs/leads to the indicator globe and give them a shake to see if the fault goes away. If it doe stop intermitantly then it will help point you in the correct area.

Jun 10, 2011 | Pontiac Firebird Cars & Trucks

1 Answer

Rear turn signal and hazard light don't flash (left side only)


The rear left turn signal bulb must be replaced immediatly before it melts the light socket, if it has'nt yet. Also please verify that the correct light bulb is being installed. because even though many bulbs look the same they are not identical. Installing the wrong bulb can be the begining of many, many problems in the particular circuit

Mar 26, 2010 | 2000 Ford Focus

2 Answers

The left signal is on all the time not flashing and even without the keys the light still on someone told is the body control module


Hi

This is a problem with the Body Control Unit. Hyundai cost cutting has meant that the flashers have been put on the main board.

Hyundai suggest changing it which will set you back £700. I suggest buying a NEC auto relay and asking a tv repair man to solder another one on for you. 9 out of ten times this will solve the problem and will cst 50 quid as oppose to £700

Mar 25, 2010 | 2003 Hyundai Tiburon

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...