Question about 2002 Nissan Quest

1 Answer

Where is the knock sensor located on a 1997 mercury villiager and is it hard to replace at home

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Located under the intake manifold center right bolted to the top of the engine block.

Posted on Jun 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't find crank sensor on 94 mercury villiager


The van uses a distributor, and the crank sensor is inside the distributor.

Jul 03, 2013 | Cars & Trucks

1 Answer

1996 mercury villiager po325 consistantly a problum even after replacement someone mention to relocate it to a grounded quiet place


Do Not ever replace a kncok sensor. It does no harm or no good. Just leave it alone.

yahoo group for villager quest owners for help.

Oct 05, 2011 | 1996 Mercury Villager

1 Answer

Where is knock sensor located?


DO NOT EVER CHANGE YOUR KNOCK SENSOR EVEN IF IT GIVES A P0325 CODE.

It's a waste of $600.

go here & we will explain.

http://groups.yahoo.com/group/villagerquest/

Feb 08, 2011 | 1997 Mercury Villager

1 Answer

Location of knock sensor on 97 mercury villager


it's in the valley of the engine. Do not ever replace it even if you get a code. A knock sensor will NEVER casue a driveabiity problem. It only retards timing 6 degrees if it senses spark knock. It also sets a code if an engine mount is broken and the engine rocks up and down on acceleration.

go here for help

http://groups.yahoo.com/group/villagerquest/

Oct 01, 2009 | 1997 Mercury Villager

1 Answer

Knock / Cam Sensor


The Knock Sensor is Located under the Intake Manifold.. It can be seen vias a flash light from the Driverside Looking down into the open area below the intake manifold approx 8in. Inside. If you are going to Remove/Replace the Knock Sensor You will have to Remove the Intake Manifold. Whick is not as hard as it may look. You will also have to replace the Gasket on the intake it self.

Jun 21, 2009 | 1997 Nissan Maxima

1 Answer

The car won't accelerate and the engine backfires.


If you haven't changed spark plug wires, do so. If you have, then check your timing / timing chain and check for vacuum leaks, or your egr. Good luck! let me know how it goes.

May 21, 2009 | 1997 Mercury Villager

2 Answers

Location of knock senor on 97 maxima se


Your knock sensor is located Under the hood, center, front engine area, below intake manifold, mounted on block.


A defective knock sensor may cause engine detonation or reduced spark advance and fuel economy. When a knock sensor is removed and replaced, the sensor must be tightened to its specified torque. If the knock sensor is installed tighter than it should be, it may become too sensitive and provide an excessively high voltage signal, resulting in more spark ****** than required. When the knock sensor is installed looser than it should be, the knock sensor signal will be lower than normal, resulting in engine detonation.

To replace the knock sensor:
  • Disconnect the knock sensor wiring connector.
  • Then, unscrew the sensor.
  • Remove the knock sensor.
  • Reverse the procedures to install the part.

May 15, 2009 | 1997 Nissan Maxima

1 Answer

Replace knock sensor 1997 mercury villager check engine light on


do not ever replace a knock sensor. It will not fix anything and it will cost you $600 for absloutely nothing. Repeat - do not waste your money.

go here for help

http://autos.groups.yahoo.com/group/villagerquest/

May 13, 2009 | 2002 Nissan Quest

Not finding what you are looking for?
2002 Nissan Quest Logo

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...