1997 Dodge Intrepid Logo

Related Topics:

A
Anonymous Posted on May 14, 2010

97 dodge interpid hazard flasher location. I have had an intermittant flasher problem this winter which has recently turned into a permanent failure. The problem so far i cannot even locate the flasher according to the fuse panel and what i have read so far there is a module to the right of the fusr panel listed on the panel as a headlamp delay i have seen both fuses for the flasher but cannot find the falsher itself or the problem that prevents it from operating a wee bit of help is needed location of flasher would be nice

5 Related Answers

Anonymous

  • 333 Answers
  • Posted on Feb 18, 2009

SOURCE: dodge spirit flasher location

You remove a few phillips head screws on the cover beneath the dash under the knee panel. The hood release is attached to the panel. You can reach it from below or remove the knee panel around the fuse box door. Look for the screws around the trim piece. It's a fairly simple process. It's a small, silver, and looks like a little can. I hope this helps. Don't forget to rate my answer, thanks.

Ad
motor1258

Mike Butler

  • 6674 Answers
  • Posted on Apr 13, 2009

SOURCE: 1993 Dodge Shadow...left turn signal won't flash

If you have trouble finding signal flasher, turn your right side blinker on, and follow clicking noise to flasher.

goalie39

Ed

  • 479 Answers
  • Posted on Apr 15, 2009

SOURCE: turn signals and hazard don't work

Next best guess is the flasher unit has failed, this could be your little blue box, pick up a replacement at any auto parts store and replace it.

motor1258

Mike Butler

  • 6674 Answers
  • Posted on Apr 30, 2009

SOURCE: I cant find the flasher unit location for my 97 dodge intrepid.

Check down under dash by left side of brake pedal area.

Anonymous

  • 3 Answers
  • Posted on Jun 26, 2009

SOURCE: 1997 dodge avenger turn signal probs and location

replace the turn signal switch it self, mine did the same thing with the left turn signal, put in fuse and it will continue to flash... went to junk yard pulled one out of a 97 avenger just like mine, swapped them out and now it works fine. looked to be like some corrosion... to repace: 3 screws under columb, 2 screws on side of signal switch (black plastic side). unplug and replace

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

Turn signals and Hazard no longer work

Fast clicking is caused by a higher than normal current being applied. Normally a short or a aftermarket relay that requires less current to switch. Sounds like the entire multifunction switch is bad.
0helpful
1answer

Turn signal problem. Are there two flashers or one?

There is one Combination Flasher that controls the turn signal system and the hazard warning system. It is located under the instrument panel between the steering with and fuse block.
2helpful
2answers

Turn signals won't flash. They do come on but no intermittant flashing. Flasher has been swapped out. All turn signal lights come on on both sides front and back.

i think you may have replaced the hazard flasher not the turn signal flasher, the turn signal flasher is located behind the dash on the right side of the steering collum support, the hazard flasher is located in the convenience center.
2helpful
1answer

1998 Dodge Durango. Turn signals stopped working intermittently, got worse, and almost never work now. The hazards still work and flash on all 4 locations. I'm wondering if it's a relay, but any...

the relay is indeed most likely the trouble. Chrysler has used two flasher relays for many years. One for turn signals and one for the 4-ways. If you want to find out for sure and the flashers are the same type you could trade one for the other and see if that solves the problem.
0helpful
1answer

Flashers on 2000 dodge durango only works intermittantly; this problem just started yesterday

Check the combo flasher,both the hazard and turn signals work off this two part flasher (one piece)
0helpful
4answers
8helpful
1answer

Have hazard lights but no running or turn signals

sounds like you need a combo flasher assembly..located in fuse block inside vehicle under steering column..there may be a plastic cover under dash you have to remove to see fuse block..large black relay that plugs into fuse block..if you pick up a new one,you will see what it looks like..available at dodge dealer..combo flasher or drl/signal relay
0helpful
1answer

Need to locate signal light flasher 2001 dodge intrepid

If you mean the flasher, which makes the turn signals and hazards to blink, then...

It's a combo flasher which operates both the turn signals and the hazard lights. To access the combo flasher with ease remove the drivers knee bolster and then remove the brake release cable end from the handles notch, then disconnect the harness from the trunk release switch. Next there will be a reinforcement panel, remove that as well. Finally locate and replace the combo flasher from behind this panel. It is a black box that has a harness connected to it with a pink wire, a black and yellow wire, a red wire, a dark blue and pink wire, and finally a black wire. To help locate the flasher either turn the turn signal on or apply the hazards and listen for its location.
Not finding what you are looking for?

121 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...