Question about 1993 Honda Accord

Open Question

How do you replace the weather stripping on the drivers side front door of a 1993 Honda Accord?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 217 Answers

SOURCE: 1993 Honda Accord VSS replacement

Chiltons guide. It can be purchased at most all auto parts stores. It has everything about your vehicle from the ground up and front to back.

Posted on Jul 11, 2008

  • 1 Answer

SOURCE: repalce front driver power window motor - 1993 cutlass ciera

Disconnect the battery negative cable, carefully remove the door panel, make sure you remove all the visible hold down screws holding the arm rest and other things in place, be careful and observant, don't force anything. If you don't have the standard door panel removal tools, use a stiff putty knife or a wide screwdriver to remove the door panel, you will have to get the power window control switch and the lock control rods out of the way, take notes so you know how they go back together, Remove the plastic weather protection shield out of the way, try not to tear it because you will want to replace it using a good contact adhesive. Getting the motor and the lift mechanism out is the biggest challenge, There are two big rivets holding the motor and regulator assembly to the door, there are two more rivets closer to the rear of the door that holds the track and window guide in place. the rivets are difficult to drill out because it's not easy to center punch them. I used my 4 inch grinder to remove the rivet heads, be careful not to injure yourself or grind through the door metal. knock the rivets out. Remove the power supply wire from the motor. Use a 10 MM socket to untighten the two cap screws that hold the lift bracket to the bottom glass channel. Don't take the cap screws all the way out. Use a piece of wire to hold the window in the closed position. Loop the wire over one of the hold down cap screws and fasten the other end through one of the convenient holes near the top of the door. Now comes the good part. the motor and lift mechanism is all in one near rigid piece. The seat belt anchor blocks the door panel opening that would make it relatively easy to remove. Don't give up, the unit will come out with some thoughtful manipulation, the V shaped track guide will tolerate a small amount of flexing, don't overdo it. I finally got the assembly out by moving it as far to the back of the the door cavity as possible, use the angles of the assembly to your advantage to free it from the door. Once free, use a black marker to ensure you align your new motor in the correct postition. If you are replacing a complete assembly that looks the same a the part you removed, install by reversing the above directions. If you are replacing only the motor, drill out the two rivets that hold the motor to the lift assembly. this will be asy to do. fit your new motor in the exact same position, referring to the previous marks you made. If you are reusing the old lift mechanism, you should pull the perforated tape out of the guide, clean, inspect it, the guide and the tape, relubricate it, I used white grease, there is probably a better grease available. The motor assembly I received from an internet supplier came with rivets and machine screws to install the assembly, I used 1/2 quarter twenty nuts and bolts to replace the big rivets, I don't have a big enough rivet gun. If you go the quarter twenty way, use thread lock, install with bolt heads on the inside the door and flat washers and nuts to the car interior. Be observant, I left the plastic bracket that attaches the drive tape to the window bottom in an unsecure place, one of my dogs used it as a chew toy,so it was off to the junkyard one more time. Be sure to secure the tape properly at both ends. If it worn or frayed, several suppliers including rockauto supply them at reasonable cost. good luck.

Posted on Oct 10, 2008

  • 1 Answer

SOURCE: Exterior rear door handle on Honda Accord 2001

To Remove Door Panel on 2001 Honda Accord:

A: To remove the plastic piece with the door lock button and door handle connected to it:

1- Remove the screw in the middle located behind a plastic cover button
2- Push (slide) the whole assembly Forward (toward front of car)
Besides the screw, it is held in place by 3 hooks on the backside that hook into holes in the metal door frame
3- Now unhook handle from small metal bar going through door by pushing (toward door) plastic clip (blue?) off of the bar, then the bar will come out of the clip hole, thus releasing the handle.
4- Depress little grey button /bar (purple painted on it)on elec. connector to seperate connector, thus releasing door lock switch

Now the whole assembly (metal handle, door lock switch, and plastic piece) will come off door panel

B: The door is held on by 2-screws, 7-plastic snaps/plugs, and 1-plastic plug.

The screws are located: bottom of hand hold and the other behind the handle, both covered by little covers that have to be pryed off to access the screws.(hint: the screw with the built in spacer goes behind the handle when you are trying to reinstall)
The 7-plastic snaps: 3 across bottom and 2 on each side. Not visible, they are mounted to the inside of the panel.
The 1-plastic plug is visible at the upper front of the panel and is the same color as the surrounding trim


C: Take off the big plastic triangle piece above the door panel and behind the mirror. Pull/pry off. It has 2 snaps holding it on. one near bottom and one near the front.

D: Light lens prys off from bottom. Unscrew (1/4 turn) the light assembly with bulb still intact from backside of panel

E: Remove the Hand-Hold/window switch assembly:

Posted on Apr 27, 2009

  • 234 Answers

SOURCE: Drivers Door Lock Problem

You will probably need to replace the power door lock actuator.

Here's a link to one similar to yours.

http://autorepair.about.com/library/a/1g/bl467g.htm

You can probably get a used one from a salvage yard.

Try this site to find one near you:
http://car-part.com

If you need more help post a comment.

Tim

Posted on May 01, 2009

  • 19 Answers

SOURCE: Honda Accord Outside handle broken and Child lock is on.

Remove the panel and disable the child lock or some cars have an option to just bypass the child lock either or

Posted on Jun 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is causing my trunk to leak on my 1993 Honda accord?


Try checking the seals. If they are cracked or pieces missing. That will cause leaking.

Dec 30, 2014 | 1993 Honda Accord

1 Answer

How long should it take me to replace the fuel filter on my 1993 HONDA ACCORD 10TH YEAR ANNIVERSARY EDITION


Its located underneath the drivers side door, about a foot towards the center of the car. depending on the tools you use, and how rusted the bolts are, and your expirience, expect to be working on it about 45 mins to and hour.

Sep 17, 2011 | 1993 Honda Accord

1 Answer

The driver's side window on my 1993 Honda Accord will not roll up. I can hear the motor when I press it down but when I press it up there's nothing. Can you please help me


Your window regulator is probably worn and the wire attached to the motor has probably been stripped and cut, not allowing it to pull the window up and longer. You will need to remove the inside door panel to inspect the window regulator and make sure it's indeed gone bad. Also, be sure to check your window lift switch too. It might be bad also.

Dec 13, 2010 | 1993 Honda Accord

1 Answer

My 1993 honda accord SE is overheating


It's certainly the water pump. Have the timing belt and balancer belt changed at the same time.

Jun 10, 2010 | 1993 Honda Accord

1 Answer

How do you replace the driver's side door handle on a 1993 honda accord


YOU HAVE TO REMOVE THE INSIDE DOOR PANEL TO GET TO THE BOLTS THAT HOLDS IT ON

Nov 14, 2009 | 1993 Honda Accord

1 Answer

Passenger front side door 05 honda accord does not


yes the actuator is specific to each door. You can replace it yourself. Just be easy when pulling things off as not to crack plastics . Both of my 03 Accord actuators are out as well.

Jul 21, 2009 | 2005 Honda Accord

1 Answer

How do you remove the door panel drivers side front on a94 accord


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Jul 15, 2009 | 1994 Honda Accord

1 Answer

Interior Carpet Getting Wet


It sounds like a plugged drain line from the air conditioner. Most cars now run in the a/c mode whenever u turn on the climate control (even when heat is on). The passenger side front is where it would be wet, and the carpet and carpet pad act like a sponge and will soak up the water. Let me know how u make out.

Oct 25, 2008 | 2003 Honda Accord

1 Answer

1993 Honda Accord V6 Sedan - Leaks fluids


Hey try checking you radiator plugs (2) at the bottom right corner make sure its not stripped. Also if the radiator in plastic on the top and very bottom but iron or aluminum in the middle you will have to check really careful where the plastic and aluminum join together could hair a hairline crack but once you start the car and it get hot and pressurize then its runs out fast. Hope this helps I have a 93 accord also..for 12 years now and still doing well..Ed

Jun 06, 2008 | 1993 Honda Accord

Not finding what you are looking for?
1993 Honda Accord Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...