Question about 1986 Mercedes-Benz 190

1 Answer

It was slugish during shifting.now it wong go into second gear.reverse works but no second gear.stuk in first

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Mercedes-Benz Master
  • 1,619 Answers

Try having the stage pistons in the side of the unit replaced and have a full fluid removal and fill with new fluid and filter, if that doesnt work it most likely time for a rebuild.

Posted on May 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

01 chevy duramax not shifting out of first gear and gear indicator flashing when in Reverse and Drive. Pops into reverse for a second then out and Drive will go in but shifts in hard.


Valve body on the transmission is not working. There are shift solenoids attached to it that control it so look for a blown fuse first.

Aug 01, 2016 | Cars & Trucks

1 Answer

2007 chevy colorado. Auto Transmission clunked during a couple of shifts then will only drive in second gear. Limp mode?? Has reverse, will drive in 1, 2,3, and d but in second gear. Got codes checked came...


Seam like transmission fluid is low.
-Start the engine, let it run for 10 minutes to normal temperature . Do not turn it off and check transmission fluid. If it's low add more fluid to full indicator. And try again.


Good Luck


Mai

Aug 28, 2014 | 2007 Chevrolet Colorado

1 Answer

I bought a 1998 Saturn SL1. During the 1 month warrenty I noticed the car would not down shift into 2nd gear. The dealership did some work on the drivetrain and then it would downshift into second. But...


Check the fluid level in you slave cylinder. If the fluid is low or there is air in the system it can cause hard shifting. If everything is ok it is problably the syncros.

May 06, 2014 | Cars & Trucks

2 Answers

How do you adjust the shift cable on a 1995 gmc jimmy, wont go into reverse or park.


On the 1995 Jimmy, the shift cable can come loose on the mount on the side of the transmission where the cable meets the trans. When it slips, the alignment goes off and causes the driver to not be able to put the trans into park. If you take a long stick you can push the shift arm on the trans to the park position and your trans will go into park.....what you (and I) really need to know is how to take the shift cable mount apart and reset it.

Aug 05, 2012 | GMC Jimmy Cars & Trucks

1 Answer

My transmission slips going through second gear if i get my foot in it just a little bit, and it doesnt always go into reverse. if i shift into reverse and it doesnt shift, i have to shift to neutral then...


this problem is a common failure associated with your shift solenoinds inside your tranny. of course a shop is not gonna tell you this because by the time you wanna get it repaired it is usually too late and have already cause damage to your clutch pack and internal parts, thats the main reason why a shop wont mess with just replacing your shift solenoid (aka valve bodie)

Feb 18, 2010 | 2000 Chevrolet Silverado 1500

1 Answer

My avalanche won't shift


Sounds like a broken internal trany part. Take it out and shift it through the gears manually to see which gears work and where it revs up. The second and fourth gears are the ones that tend to not work.

Oct 11, 2009 | Chevrolet Avalanche Cars & Trucks

1 Answer

Car won't go into gear properly


it could be a few things bent shifting fork or first gear is out reverse runs off an idler that is conected to first gear.

Jun 05, 2009 | 1999 Nissan Altima

1 Answer

Car not shifting into second gear


If the car is grinding when going into reverse, you need to have the clutch bled or repaired.

If it goes into reverse with out grinding, I am sorry to tell you your problem is internal to the gearbox. Bad or damaged Syncro

Good luck



Nov 20, 2008 | 2007 BMW 525xi Sedan

1 Answer

Clutch problem


Hi,
check out for worn out clutch plates . The second problem could with a worn out gear. Do all gears make a sound during the change or its the lower gears . Generally the First- second shift and Reverse gears cause this problem on the Accent .


Thanks
proton

Aug 04, 2008 | 1999 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...