Question about 2001 Mazda Millenia

Open Question

Where is the crankshaft sensor on a mazda millenia (2001) 2.5L? also, how does one go about changing it

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75822 Answers

SOURCE: Location under hood for fuel pump relay on 2002 Mazda Millenia S

JUST RELEASE THE PRESSURE AT THE FUEL PRESSURE TEST PORT ON THE FUEL SUPPLY RAIL THAT SUPPLIES THE INJECTORS, IT IS A METAL VALVE LIKE A TIRE VALVE, THAT IS THE FACTORY RECOMMENDED METHOD..

Posted on Mar 11, 2009

  • 94 Answers

SOURCE: need to change crankshaft position sensor for 2001 elantra

down by your crank shaft pulley you will find a sensor with 2 wires ruining into it and 1 bolt holding the sensor in remove the bolt and twist and pull on the sensor then slide the new sensor in then reinstall bolt and wire

Posted on Mar 08, 2009

  • 1 Answer

SOURCE: 2001 Mazda MPV upper front oxygen sensor change

I replaced this sensor about 6 months ago. (If this is the sensor that is located near the firewall on the exhaust manifold under the ignition coil.) The only way to easily replace it, is to remove the MAF and air filter assy. then remove the intake plenum, remove the ignition coil, and then you'll have access to the sensor. You'll need a sensor removal socket. If the socket slips around the hex of the sensor, then you'll need to use a regular deepwell socket and cut the cable from the top of the sensor, or use a combination wrench that will fit it.
The most difficult part of removing the intake plenum is getting the nut loose from the EGR valve. DO NOT just remove the two bolts holding it to the intake plenum. It will not line up correctly during re-assembly and may not seal tightly either.
This took about a Saturday to do. You'll need new plenum gaskets to replace the old. While your at it remove the throttle body and clean the carbon from the ports that lead to the EGR valve and replace that gasket as well. The gaskets will run about $30.

Posted on May 04, 2009

  • 149 Answers

SOURCE: 2001 Mazda Millenia Door Panel Removal

should be some screws in the door handle/armrest and you can use a screwdriver around the edges to pop the rivets they are just plastic and can be replaced for a few dollars if you mess a few up-or they do sell a door panel puller tool also-the whole panel should come off as one piece handle buttons and all and will be limited in the distance you can move it due to wiring bundles connected to door locks power mirrors and stuff-hope that helps

Posted on May 20, 2009

  • 750 Answers

SOURCE: my hold light is flashing in my 2001 mazda millenia

hold light flashing means you have a transmission fault of some kind, check vehicle speed sensor

Posted on Jul 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT PARTS DO YOU NEED TO TAKE OFF TO CHANGE THE CRANKSHAFT POSITION SENSOR


The splsh gaurds under the car then you should be able to see the sensor its right behind the lower belt pully the hormonic balancer Its easy to replace and will make a world of differance in how the vehicle runs if its bad

Nov 11, 2010 | 2002 Mazda Millenia

2 Answers

2002 mazda millenia mass air flow sensor


MASS AIR FLOW SENSOR IS ATTACH TO AIR DUCT TO AIR CLEANER HOUSING.

Sep 16, 2009 | 2002 Mazda Millenia

2 Answers

Mazda Millenia 1997...flashing hold light when driving car...car changes gear like there is no clutch


you mean check engine light flashing??? if so then the engine is skipping and the lack of power putput will cause the trans to change gears constantly. is this the issue you describe?

Sep 03, 2009 | 1997 Mazda Millenia

1 Answer

My hold light is flashing in my 2001 mazda millenia


hold light flashing means you have a transmission fault of some kind, check vehicle speed sensor

Jul 02, 2009 | 2001 Mazda Millenia

1 Answer

1997 Mazda Millenia, Changed Almost Everything, Still No Spark..


check the pcm .get it scan make sure your pcm is working.also check ignition coils.

Apr 20, 2009 | 1997 Mazda Millenia

1 Answer

Crankshaft Position Sensor On A 1997 Mazda Millenia


No way you need to open the timing belt to get to it , Mazda sucks.

Apr 15, 2009 | 1997 Mazda Millenia

1 Answer

1999 MADZA MILLENIA


This could be crankshaft sensor. If it is, yes it will stop it from starting.

Jan 24, 2009 | 1999 Mazda Millenia

1 Answer

Check engine light


yes the sensor and it will not go away on Mazda Millenia even though you replace that code it will show another one Mazda Millenia Sucks & Mazda Parts are Expensive too

Jan 15, 2009 | 1998 Mazda Millenia

Not finding what you are looking for?
2001 Mazda Millenia Logo

Related Topics:

576 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...