Question about 1992 Chevrolet S-10 Blazer

Open Question

Where is the knock sensor 1992 S10 Blazer - 1992 Chevrolet S-10 Blazer

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
rockitman187
  • 2559 Answers

SOURCE: S10 blazer speed sensor where's location for replacement

On the rear axle.

Posted on May 06, 2009

Ad
  • 95 Answers

SOURCE: how many knock sensors does a 93 S10 blazer 4.3

one

Posted on Jan 01, 2010

  • 89 Answers

SOURCE: loud whine then knock in overdrive

well, without hearing the noise myself, i could guess that the torque converter clutch might be going bad. the torque converter is the part that transfers the power from the engine to the transmission via viscous fluid motion, the converter also has a clutch that internally provides a direct connection inside the converter for better fuel economy. but as with anything labeled as a clutch, it wears down to a point where is slips. the noise your hear could be the torque converter clutch slipping. i owned a 90 astro van with the same drivetrain that made a noise similar to what you speak of up hills. while driving up hills, fully depress the accelerator and if the clunking noise occurs, then the whine goes away as you accelerate faster in a lower gear, very likely this is the case. you would have to have a transmission shop diagnose further. i drove that old van for five more years cause i didn't want to pay to have transmission repaired. it can be very expensive.

Posted on Jul 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater only blowing out floor board 1992 s10 4.3


there is a motor to change duct positions under the dash. either the motor is unplugged or the motor is bad

Mar 24, 2013 | 1992 Chevrolet S-10 Blazer

2 Answers

Where is the ECM located on a 92 S10


The ECM on a 1992 S10 and S10 Blazer is located below the glove box.

Jun 12, 2012 | Cars & Trucks

2 Answers

On my 1991 chevy blazer s10 I get error code 43. What is it and how do I fix it


Hi, the indication is that your computer is not receiving a good signal from the knock sensor. Recommend you check the connector on the sensor and the wire. Also make sure the sensor isn't loose in the block. If those look good, you may want to just replace the sensor. A new one is $30 at autozone. Without the knock sensor signal, the computer will default the ignition timing toward a less fuel efficient value. The sensor looks like the picture below and is mounted in the engine block. You may have 2 knock sensors--one on each side of the engine. Sorry, but I could not find a good picture of the location. I will keep looking for one, though.

jturcotte_426.jpg

Apr 08, 2011 | 1991 Chevrolet S-10 Blazer

1 Answer

I got a 1995 chevy blazer s10 with a 4.3 v6 engine wont start when it does start it is missing bad had it analized at auto zone came back a knock sensor, tps sensor, & egr valve what should i check...


In order I would go for the EGR valve, then the TPS. A malfunctioning EGR will keep the car from starting and make it run very rough if you do get it started. The car will run without the knock sensors so I would wait until it runs better before getting those. There are two knock sensors one for each bank of cylinders on the V6. Autozone should be able to tell you which sensor goes on which side.

Feb 08, 2011 | Chevrolet Blazer Cars & Trucks

2 Answers

Were is the esc module on a 93 s10 blazer 4.3 vortec located


Welcome to FIxYa.com



leedavidian_46.jpg



Thank you for using FixYa.com

Regards, Lee Davidian

Nov 22, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

What reading for map sensor chevy blazer s10 1989 2.8...what numbers?


CODE 33 MAP SENSOR SIGNALVOLTAGE OUT OF RANGE HIGH. CODE 34 MAP SENSOR SIGNAL VOLTAGE OUT OF RANGE LOW.

Jun 24, 2010 | 1992 Chevrolet S-10 Blazer

1 Answer

Loud knocking in the engine of a 2000 4.3 l chevy blazer.


if it is not mechanical try your anti knock sensor. i had one go out on my v8

Jul 23, 2008 | 1992 Chevrolet S-10 Blazer

Not finding what you are looking for?
1992 Chevrolet S-10 Blazer Logo

Related Topics:

549 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75842 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...