Question about 2005 Chevrolet Colorado

1 Answer

Left front hub replacement 2WD. - 2005 Chevrolet Colorado

Posted by on

  • martin salvas
    martin salvas Jul 13, 2014

    hello I have a chevrolet colorado z85 LS 2wd it is the torque for the 4 bolts left front hub bearing? help me plz

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

2WD pickups don't have hubs. They have rotors with bearings. Once you have the brake assembly supported, remove nut from spindle. Be sure not to strip the threads on the spindle. Remove the front set of bearings and pull the rotor off. Remove the rear set of bearings. Be sure to pack greases into new bearings prior to installation. Insert new rear bearing into rotor and replace onto spindle. Insert new front bearing and washer and re-install nut. Tighten to recommended torque specs, grease fittings and replace brake assembly.

Posted on May 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2wd.how to replace front wheel bearing assembly


There are a number of videos...
For RWD front hubs. (F250 will just have larger bolts.)

How To Install Replace Front Wheel Bearing Hub Assembly 2004-08 Ford F150
For 4x4 front hubs.

Ford Super Duty hub bearing replacement Driver side

May 06, 2016 | 2005 Ford F 250 Super Duty

1 Answer

Wheel bearing replacement


25 days old.??
car has 4 wheels, must be guess end of car?
2wd or 4wd, yup , be different.
why not just log in to mitchells DIY and end the saga... google it)
ill toss coin for you, lands heads, for front.
front wheel bearings.
2wd
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and support the front end.
  3. Remove the caliper from the anchor plate and suspend it out of the way.
  4. Disconnect the ABS sensor.
  5. Remove the rotor.
  6. Remove the bolts attaching the hub to the knuckle.
  7. Installation is the reverse of removal. Torque the hub bolts to 76 ft. lbs. (103 Nm).
4wd:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Place the transfer case in 2WD.
  3. Raise and support the front end.
  4. Remove the caliper from the anchor plate and suspend it out of the way.
  5. Remove the rotor.
  6. Loosen the caulking around the front driveshaft nuts. Remove the nuts and discard them.
  7. Remove the 4 hub retaining bolts. NOTE If the hub is difficult to remove, install 2 long bolt in the bolt holes and strike them to loosen the hub.
  8. Installation is the reverse of removal. Torque the hub bolts to 76 ft. lbs. (103 Nm). Use new driveshaft nuts, torquing them to 181 ft. lbs. (245 Nm). Apply new caulking. The caulk should be free of cracks when applied.

May 01, 2016 | 2003 Isuzu Rodeo

1 Answer

Front diff binding with or without diff locked


try checking the cv ("U") joints for the front drive

Sep 19, 2015 | 2008 Ford Ranger 3.0

1 Answer

Replaced front hubs and still have roaring noise


clicking noise from front end while spinning tyres is an indication of failing cv joints. especially while turning the wheel from left to right. Suggest you replace the shafts

Jan 27, 2013 | 2004 Chevrolet Tahoe

1 Answer

On my 2001 Dodge Ram 1500 5.2 2WD, I just found


This is a very simple job to do. Raise the front of truck off the ground,block the rear tires. Using pliers and a hammer,remove the grease cap from hub. Remove the cotter key and nut from axle,pull out slowly and remove outer bearing. then remove hub from axle. To remove inner bearing ,prop hub on a board and use a large punch to drive out bearing and seal. Clean out inside the hub and install new bearing and seal. Replace all parts in the reverse as you took them off. Hope this will help you.

May 14, 2010 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

On my 2001 Dodge Ram 1500 5.2 2WD, I just found out that I have to change the front hubs if I want to replace the front wheel bearings. How insane is that! What can I do to have a front hub that I can...


buy an older truck to answer question all newer model vehicles have gone to a hub/flange bearing assembly these bearing setups handle loads without or very minimum variance, when you go into a cornering situation these bearing setups give you a steady and consistent track thus a better handling vehicle now instead of cleaning and repacing tose old cone and race style bearings you just unbolt hub assembly and any related abs sensors and bolt on new

Mar 24, 2010 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

2005 dodge 2wd 3500 front hub assembley.. how do i


there are three mounting bolts behind the wheel studs
remove the bolts
remove abs sensor
slide the hub out of steering knuckle

Mar 05, 2010 | 2005 Dodge Ram 3500

1 Answer

My friend has jus bought a 1992 Pajero, 2.5 auto, swb, no manual with it. He has heard that when changing from 4x4 to 2wd that you need to stop the vehicle, go intp 2wd, then reverse for a couple of yards...


He need not stop to change from 4x4 hi to 2wd. He can also go from 2wd to 4x4 hi "on the fly" as long as the front hubs are locked, he is going straight and maintaining a steady speed. If the hubs are manually locking, he must exit the vehicle and lock the hubs. If they are automatic locking, in order to go from 2wd to 4x4 he must stop, put the vehicle in 4wd hi and pull off. Once he starts moving, the hubs will automatically lock, he can then switch from 2wd to 4wd hi and vice versa "on the fly". To unlock the hubs, he will need to stop, put the vehicle in 2wd and back up 3 ft. (remember, this is on automatic locking hub models). Hope this is helpful!

Nov 05, 2009 | 1993 Mitsubishi Montero

1 Answer

Replace front rotor


If it is like most cars the rotor slips over the hub. If not remove the hub and see if there is a bolt there. You have to hit it pretty hard, like with a small sledge hammer with a block of wood against the rotor.

Apr 18, 2009 | 1998 Dodge Ram 2500 2WD

Not finding what you are looking for?
2005 Chevrolet Colorado Logo

457 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...