Question about Dodge Ram Pickup 1500

1 Answer

Turn signals, brake lights, and hazards all quit workin. Checked all the fuses, both in the truck and in the power distrubution box. What should i look for next?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

See if you have voltage going to the sockets, if so bad taillight ground, if not go to the signal switch and check there, fo signal in and out

Posted on May 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signal and hazard lights are not workin


Probable cause is what we used to call a stacker switch, Your car should have 2 of them, 1 for the turn signals and 1 for the flashers or hazard lights, Normally the turn signal switch is located in the fuse box, a round plug in switch, easy to change and cheap too.

Nov 14, 2013 | 1998 Mercury Grand Marquis

2 Answers

!997 Ford Thuderbird brake lights and hazards do not work


Lets start at the beginning.
The turn signals and brake lights use different fuses but both go thru the turn signal switch and use the same bulbs.
Have you checked the fuses for each circuit and does each switch have power in and out ?

Feb 03, 2013 | 1997 Ford Thunderbird LX

1 Answer

Rear lights not working on 2002 suzuki grand vitara


In the underdash fuse/relay box, the 15A TAIL fuse feeds power to the coil of headlight relay 2. When the combination switch is set to TAIL, the relay closes and the outer tail lamps light. In the same underdash fuse/relay box, the 20A STOP fuse feeds power to the brake light switch. When the brake pedal is pressed, the inner brake lamps light. The underdash fuse/relay box also contains the 10A TURN BACK fuse which feeds power to the hazard switch and the turn signal relay. Relay output is fed to the combination switch and turn signal power is applied to the selected middle tail light. The fourth fuse in the underdash fuse/relay box is the 15A HAZARD fuse which feeds power to the hazard switch and turn signal relay. When the hazard switch is set, the turn lamps on both sides begin flashing.

Sep 18, 2012 | 2002 Suzuki Grand Vitara

3 Answers

I have no brake lights or turn signals on my 95 gmc truck. I have replaced the boards but no luck. Also have checked fuses.


OK if the fuses are good , use a test light and check to be sure you have power at the fuse terminals. you'll check from ground to the terminal on top of the fuse. you should have 12vdc. then , check for power at your brake light switch on both terminals while the brake pedal is pressed, it is located located on the brake pedal assembly. also , check your hazard flasher switch to be sure it is not on. if it was on, check your flashers, both the turn signal and hazard flasher. If everything checks out , your problem is probably in your turn signal switch assembly located in your steering column.

Mar 14, 2010 | 1995 GMC Sierra

1 Answer

My brake, hazard and turn lights dont work, i


well u have two seprate problems the hazards and turn signals have a flasher that needs replacing if the fuse is good on the fuse box marked signals .and there is a brake light switch under the dash board near the brake pedal it has two wires on it check the wires make sure they are connected if so replace the brake light switch

Nov 13, 2009 | 2002 Chevrolet Astro

2 Answers

No brake lights, turn signals, or 4-ways.


Did you actually check the bulbs? I believe your brake lights, signal lights, hazards all use the same bulb for each side.

Your brake lights may be your brake switch just above your brake pedal.
The signals could be your electronic flasher module (EFM) located under the dash near the steering column.
Your hazards may be affected by the EFM, but not likely and the switch for your hazards may be faulty

Sep 10, 2009 | 1998 Chevrolet Blazer

1 Answer

Checked all fuses-good, swapped bulbs-good, hazard lights-good, head lights good, turn signals-good but no brake lights. 1995 chevy silverado


Does the turn signals or hazards work in the rear?? Yes... it may be the brake switch or the turn signal switch (power goes from battery, to the brake switch then to the turn signal switch, then to the lights. No? .. again.. possibly turn signal switch or the wiring between cab and bed.

Jun 04, 2009 | 1996 Chevrolet K1500

2 Answers

Bottom brake lights and hazard lights do not come on. All other lights work including top brake lights. Fuses and bulbs checked.


Check for power out of brake light switch by brake pedal. Of its faulty , the 3rd brake light will still work. Hope this helps

May 20, 2009 | 2000 GMC Yukon Denali

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...