Question about 1993 Jeep Wrangler

1 Answer

The interior lights on 1993 Jeep Wrangler have no

The interior lights on my 1993 Jeep Wrangler have no power to them. The fuse looks fine, but I can not find and power to the circuit.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

Find the pin switch on the front of the drivers side door jam, check the back side of the switch, (near the E brake pedal) make sure the plug is attached. It just plugs in. It is easy to plug and unplug the wiring to this switch on the YJ's so you can drive with the doors off and not worry about your interior lights being on and draining the battery when the engine is off.

Posted on Mar 14, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the fuse number for interior lights


pop out the fuse and look for the number.

Jun 20, 2014 | 1989 Jeep Wrangler

1 Answer

1993 jeep wrangler yj speedometer and odometer do not work


first check your fuses, then if thay are fine and veh has a veh speed sensor vss, it may have a bad connection, or the sensor may be bad, (located on the transmission)

Aug 26, 2012 | 1993 Jeep Wrangler

1 Answer

Tail lights and parking lights not working on a 1993 jeep wrangler...replaced fuse


do you have a trailer wiring harness installed? very often this is poorly done, a causes a lot of problems with rear exterior lights.

Dec 21, 2010 | 1993 Jeep Wrangler

1 Answer

Hi! I have an 1989 Jeep Wrangler 6 cylinder 4x4. I was going down the road last night and head lights, tail lights, dash lights, break lights quit. I do have turn signals. Fuse looks good!! All worked...


look for a broken feed wire somewhere ,sorry i have no product knowledge to tell you where to look first ,but under bonnet is often a fuse box with the big main fuses that feed the fuse box inside the vehicle ,

Aug 21, 2010 | 1989 Jeep Wrangler

1 Answer

1994 jeep wrangler needs headlights working and it is not the fu


i have a 1989 wrangler. for no resan i know of the head light tail lights and interior lights stoppede working? anoone know why?

Jul 24, 2010 | 1994 Jeep Wrangler

1 Answer

How do I add a lighting circuit to a 2008 jeep wrangler


If your doing this because you want to add interior lights (i.e. when you open the door the lights turn on) there is several ways of doing it... probably the easiest way would be to locate your inside fuse box and find the fuse for you factory interior lights (the polarity should be positive+). then run a wire form the fused side to your new lights... tap a ground and your golden...

Mar 28, 2010 | 2008 Jeep Wrangler

2 Answers

Ignition on 88 jeep yj not working


sounds like your ECM might be bad. Is there anything else that will turn on besides the lights? It could just be a main fuse. I'd start at the interior fuses if any and then go to the main fuse block and check for any loose wires or blown fuses first.

Jan 13, 2010 | 1988 Jeep Wrangler

1 Answer

I have a 95 jeep yj wrangler none of the gauges work . it starts and runs fine and the headlights work but that is it .


ffirst check all your fuses, then check all the connections at the battery, then make sure the fusible links are good,also theres a power wire that comes through the firewall that feeds the interior the connector goes bad, and one more thing is to take a good look at the ignition switch it the steering column. hope this helps.

Dec 26, 2009 | 1995 Jeep Wrangler

2 Answers

Removing doors from Jeep Wrangler - Dome Light Stays On


look on the reverse side of your fuse panel door

Jun 28, 2009 | 2000 Jeep Wrangler

Not finding what you are looking for?
1993 Jeep Wrangler Logo

Related Topics:

227 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...