Question about 2001 Chrysler PT Cruiser

1 Answer

How do you mount a tie rod on a pt cruser does it mount from the bottom or from the top of the spindel arm

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 564 Answers

Look for the (taper),,is on top or bottom,,on the spindle arm,,

Posted on May 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do the sway bar links and tie rods relate? Or are they completely different?


A sway bar is mounted on the chassis and most times connected to the bottom control arm on the front. They control the roll of the vehicle when cornering.
A tie rod is the bar that goes between the steering rack or drag link and the steering arm. Tie rods are a part of the steering, all cars have tie rods while not all cars have sway bars.

May 31, 2015 | Cars & Trucks

1 Answer

Front lower control arm replacement


To remove the lower control arm raise and support your car with jack stands.Next you want to remove the wheel that you are replacing the control arm on.Remove the ball joint nut and tie rod nut.Tap the steering knuckle to break the tie rod end loose from the knuckle DO NOT HIT THE TIE ROD SO HARD YOU DAMAGE THE THREADS.If you do you will also be changing a tie rod end.Tap on the steering knuckle until your ball joint stud comes loose.Remove the 2 bolts that mount the control arm to the frame.To install the new one just go in reverse.

Mar 09, 2011 | 2006 Ford Mustang

1 Answer

Death wooble on a 2005 dodge ram 2500 quad cab 4x4


The easiest way to troubleshoot it would be to jack up the front end and put jack stands under the front axle. Have a friend grab one of the front tires and wiggle pretty hard. (Make sure steering wheel is locked). To check the ball joints have them push/pull on the top and bottom of the tire and see if there is any movement between the spindle and ball joint. If not, check the tie rods next. (have them push in on one side of the tire, pull out on the other, not top and bottom this time). While they are doing this, lay under it the tie rod ends. If there is no movement (slop), check the drag link for play. If those check out, look at where the drag link mounts to the pitman arm on the steering box to see if the top link is shot or if the pitman arm is bad.

If all of this checks out ok, have your front tires checked. Tires that are out of balance can wobble pretty good as well.

Jun 03, 2010 | 2004 Dodge Ram 1500

1 Answer

Remove/replace shock absorber assembly 900s 1995 saab


  1. Slightly loosen hub center nut when all four wheels are on ground.
  2. Raise and support vehicle, then remove five wheel bolts and wheel.
  3. Remove hub center nut, then the wheel sensor,
  4. Press back brake piston using slip-joint pliers,
  5. Remove caliper from steering swivel member, then suspend in wheel housing with cable tie.
  6. Remove brake disc and back plate, then slightly loosen tie rod end nut.
  7. Press out tie rod end nut using puller tool or equivalent.
  8. Remove nut and tie rod end bolt, then the anti-roll bar to swinging arm nut.
  9. Remove outer ball joint nut.
  10. Press ball joint out of steering swivel member using puller tool or equivalent, installed on spring link.
  11. Remove nut and discard. This self-locking nut must not be reused.
  12. Remove three upper mounting nuts for MacPherson strut, then the strut.
  13. Clamp MacPherson strut in vice.
  14. Compress spring using spring compressor or equivalents.
  15. Hold piston rod and remove nut using MacPherson strut socket tool 89 96 662, or equivalent. This is a self-locking nut and must not be reused.
  16. Remove mounting and top spring seat, then the coil spring, gaiter and compression stop.
  17. Unscrew damper using wrench tool No. 89 96 670, or equivalent, then remove damper from strut.
  18. Reverse procedure to install, noting the following:
    1. Screw damper in place using wrench tool No. 89 96 670, or equivalent.
    2. Lower end of coil spring should abut against stop in bottom of spring cup.
    3. Position MacPherson strut on vehicle and install three retaining nuts on top mounting. Tighten nuts alternately, according to specifications.
    4. Always use new hub center nut with self-locking threads.

Jun 04, 2009 | 1995 Saab 900

2 Answers

Shimmy on front when accelerating of my 2006 pt cruiser


yes this is either a tie bad tierod end or ball joint

May 25, 2009 | 2006 Chrysler PT Cruiser

1 Answer

1994 chevy cavalier,inner tie rod end.


Usually they can be replaced with a little effort. You would need to get under the car and pry the broken part off the control arm. The tierod end is threaded onto the shaft. There is a bolt which compresses the tierod end onto the tierod. Loosen the compression bolt and unthread the end from the shaft rod. Counting the number of turns to remove it will be the number of turns to replace it. Mount it and then get a front end alignment which is a good idea before something else breaks.

Apr 18, 2009 | 1994 Ford Escort

1 Answer

Replacing a front wheel bearing


here is a step by step instructions on how to replace your bearing. please copy and paste the link into your browser for an image.

please do not forget to rate and comment about your experience with fixya today.

Removal & Installation
  1. Apply the brakes and hold in place.
  2. Raise the vehicle.
  3. Remove the front tire and wheel assembly.
  4. Remove the cotter pin, lock nut and spring washer from the hub nut.
  5. While the brakes are applied, loosen and remove the hub nut on the end of the driveshaft.
  6. Release the brakes.
  7. Remove the front disc brake caliper and adapter as an assembly, and the brake rotor from the steering knuckle.
  8. Remove the nut attaching the outer tie rod to the steering knuckle. To do this, hold the tie rod end stud with a wrench while loosening and removing the nut with a standard wrench or crowfoot wrench.
  9. Remove the tie rod end from the steering knuckle using Remover, Special Tool MB991113.
  10. Remove the tie rod heat shield.
  11. Remove the nut and pinch bolt clamping the ball joint stud to the steering knuckle.

    CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during removal. Hold the bolts stationary in the steering knuckles while removing the nuts, then tap the bolts out using a pin punch.
  12. Remove the two bolts attaching the strut to the steering knuckle.

    NOTE Use caution when separating the ball joint stud from the steering knuckle, so the ball joint seal does not get cut.
  13. Separate the ball joint stud from the steering knuckle by prying down on lower control arm and up against the ball joint boss on the steering knuckle.

    NOTE Do not allow the driveshaft to hang by the inner C/V joint; it must be supported to keep the joint from separating during this operation.
  14. Pull the steering knuckle off the driveshaft outer C/V joint splines and remove the steering knuckle.

    NOTE The cartridge type front wheel bearing used on this vehicle is not transferable to the replacement steering knuckle. If the replacement steering knuckle does not come with a wheel bearing, a new bearing must be installed in the steering knuckle. Installation of the new wheel bearing and hub must be done before installing the steering knuckle on the vehicle.
  15. If the wheel bearing and hub need removal. Do not reuse the wheel bearing.
    http://www.chiltonlibrary.com/content/images/32050/images/32050_ptcr_g0035.gif The separation of the ball joint and the knuckle
To install:
  1. Slide the hub of the steering knuckle onto the splines on the driveshaft C/V joint.
  2. Install the steering knuckle onto the ball joint stud aligning the bolt hole in the knuckle boss with the notch formed in the side of the ball joint stud.
  3. Install a new ball joint stud pinch bolt and nut. Tighten the nut to a torque of 70 ft. lbs. (95 Nm).

    CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during installation. Install the nuts while holding the bolts stationary in the steering knuckle.
  4. Position the lower end of the strut assembly in line with the upper end of the steering knuckle and align the mounting holes . Install the two attaching bolts. The bolts should be installed with so that the nuts face towards the front of the vehicle once installed. Install the nuts. Holding the bolts in place tighten the nuts to a torque of 40 ft. lbs. (53 Nm) plus an additional 90° turn after the specified torque is met.
  5. Place the tie rod heat shield on the steering knuckle arm so that the shield is positioned straight away from the steering gear and tie rod end once installed. Align the hole in the shield with the hole in the steering knuckle arm. Install the outer tie rod ball stud into the hole in the steering knuckle arm. Start the tie rod attaching nut onto the stud. Hold the tie rod end stud with a wrench while tightening the nut with a standard wrench or crowfoot wrench. To fully tighten the nut to specifications, use a crowfoot wrench on a torque wrench to turn the nut, and a wrench on the stud.
  6. Tighten the nut to a torque of 40 ft. lbs. (55 Nm). Install the brake rotor, disc brake caliper and adapter.
  7. Clean all foreign matter from the threads of the driveshaft outer C/V joint. Install the hub nut in the end of the driveshaft and snug it.
  8. Have a helper apply the brakes. With vehicle brakes applied to keep brake rotor and hub from turning, tighten the hub nut to a torque of 180 ft. lbs. (244 Nm)
  9. Install the spring washer, lock nut and cotter pin on the hub nut. Wrap the cotter pin ends tightly around the lock nut.
  10. Install the tire and wheel assembly. Install the wheel mounting nuts and tighten them to a torque of 100 ft. lbs. (135 Nm).
  11. Lower the vehicle.
  12. Set the front toe on the vehicle to required specification.

Apr 17, 2009 | 2003 Chrysler PT Cruiser

1 Answer

I need step by step instructions to replace front struts.


1.Turn ignition to OFF position to place steering column in unlocked position.
2.Remove hub nut
3.Loosen, but do not remove, three top mount-to-shock tower
4.Raise vehicle on a hoist.
5.Remove tire and wheel assembly
6.Move brake caliper and wire out of the way
7.Remove brake rotor
8.Remove cotter pin from tie rod end stud and remove slotted nut.
Discard cotter pin and nut
9.remove tie rod from knuckle
10.Remove stabilizer bar link nut, and remove link from strut
11.Remove and discard lower arm-to-steering knuckle pinch bolt and nut. (A drift punch may be used to remove bolt.) Using a screwdriver, slightly spread knuckle-to-lower arm pinch joint and remove lower arm from steering knuckle.
12.Press halfshaft from hub
13.Remove shock absorber strut-to-steering knuckle pinch bolt. Using a large screwdriver, slightly spread knuckle-to-strut pinch joint, if required, for removal
14.Remove steering knuckle and hub assembly from shock absorber strut
15.Remove three top mount-to-shock tower nuts and remove strut and spring assembly from vehicle
16.Compress spring with Spring Compressor
17.Place 10mm box-end wrench on top of shock strut shaft and hold while removing top shaft retaining nut with a 21mm 6-point crow foot wrench and ratchet
18.Loosen Spring Compressor , then remove top mount bracket assembly, bearing plate assembly and spring.
INSTALLATION
1.Place a 10mm box-end wrench on top of shock strut shaft and hold while tightening top shaft retaining nut with a 21mm 6-point crow foot wrench and ratchet to 53-72 Nm (40-53 lb-ft).
2.Install strut and spring assembly and three top mount-to-shock tower nuts
3.Install steering knuckle and hub assembly to shock absorber strut.
4.Install a new shock absorber strut-to-steering knuckle pinch bolt. Tighten to 98-132 Nm (73-97 lb-ft).
5.Install halfshaft into hub
6.Install lower arm to steering knuckle ensuring that ball stud groove is properly positioned and boot seal is not damaged. Install a new pinch bolt and nut. Tighten to 53-72 Nm (40-53 lb-ft).
7.Install stabilizer bar link to strut and install a new stabilizer bar link nut. Tighten to 77-103 Nm (57-75 lb-ft).
8.Install tie rod end onto knuckle.
9.Install a new tie rod end slotted nut. Tighten to 31-47Nm (23-34 lb-ft).
10.Install a new slotted nut retaining cotter pin.
11.Install brake rotor
12.Install brake caliper
13.Install tire and wheel assembly
14.Tighten three top mount-to-shock tower nuts to 30-40Nm (23-29 lb-ft).
15.Lower vehicle and tighten hub nut to 230-275 Nm (170-202 lb-ft)
16.Depress brake pedal several times prior to moving vehicle.

Hope this helps. Good luck !

Mar 14, 2009 | 1992 Ford Taurus

1 Answer

Tie rod inner or outter/how to install


here is word for word what the manual says:

REMOVAL:
1. Loosen the front wheel lug nuts on the side to be dismanteld. Raise the vehicle and support it securely on jack stands. CAUTION: If the vehicle is equipped with Automatic Ride Control (ARC), make sure the air suspention switch is turned to the OFF position before the vehicle is riased to prevent damage to the system components.

2. Remove the front wheel.

3. Remove the cotter pin and loosen the nut on the tie-rod end stud. Discard the cotter pin.

4. Disconnect the tie-rod end fron the steering spindel with a Pitman arm puller.

5. Loosen the tie-rod end jam nut and back it off several turns.

6. Apply a paint mark to the theads adjacent to the adjusting sleeve or tie-rod end. Unscrew the tie-rod end from the adjusting sleeve or connecting rod.

INSTALLATION:
7. Install the tie-rod end into the adjusting sleeve or connecting rod. Thread the tie-rob end in until the marks made on step 6 align.

8. Install the tie-rod end to the spindle. Make sure the front wheels and steering wheel are in the stright ahead position. Make sure the tie-rod stud is seated in the taper to prevent it from turing while tightening the nut.

9. Install the new nut on the stud and tighent it to the proper torque (45-60 ft-lbs). Install a new cotter pin and bend the ends over completely.

10. Tighten the tie-rod adjusting sleever clap bolts or jam nut to 50-68 ft-lbs. Make sure the tie-rod is posistioned correctly in the same posistion it was in before it was removed.

11. Install the wheel and lug nuts. Lower the vehicle and tighten the lug nuts.

12. get the front end aligned.

Aug 10, 2008 | 2000 Ford Explorer

2 Answers

Knocking from front right wheel


LOWER WISHBONE OR TIE ROD GO FOR THEM FRIST,THEN BUSHES (ANTI-ROLL)

Jun 06, 2008 | 2003 Audi A4 Cabriolet

Not finding what you are looking for?
2001 Chrysler PT Cruiser Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...