Question about 2002 Ford Explorer

1 Answer

Rear passenger side window motor works but the wire to raise and bring down is bound this caused the wire to pull from piece connected to the window what are my options... it looks like the motor and wire is salvageable . but need to know what the connector piece to the window is called

Posted by on

Ad

1 Answer

You get the regulator cable (wire) assy,it broke where it attaches to window

Posted on May 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Passenger side power window


Remove inner door panel...Push window up with hand until you can grasp the top edge...Bring to top and hold in place with packing tape...You will need to replace regulator/motor ...saailer

Aug 26, 2014 | 1997 Ford Expedition

1 Answer

Power window wont work


Probably a bad switch. Try removing the panel and with a 12 - 18 volt drill battery by your side, disconnect or cut the heavy gauge wires going to your motor. Use the drill battery to attempt to raise your window. reverse the connections if the window doesn't do anything. If it raises, reconnect your wires and tape them up and replace your switch

Jun 23, 2012 | 2003 Dodge Durango

1 Answer

I have a 1994 Toyota Camry and the power window on the passenger side has gone down, under power. Then nothing would happen when I would pulled up on the switch on the driver side main switch and the also...


more than likely one of the switches are bad (down side of switch works but up side of switch dont) being as the switches are wired together if one goes bad other one won't work either take the switch out one of back doors should be same as front passenger door put rear switch in front passenger door if works then u know front door switch is bad if it doesn't then drivers door switch is bad
u replaced window regulator Did that come with motor too??? if not check to see if motor is good
there is two wires going to motor cut isolation back on wires and using some jumper wires attach one wire to positive terminal of a 12 volt battery attach other wire to negative terminal of battery window should move up or down reverse connections and window should move other way

Jan 29, 2011 | 1994 Toyota Camry

1 Answer

2005 Nissan Frontier LE....The Driver side window will not go down or the rear passenger side. The passenger side will go down with it's own switch but not the driver switch. The driver side switch will...


The problem is that you probably have pushe dhte rear window button thinking it wasthe front window button. Have you ever pushed the rear window button thinking it was the front and then push harder. Inside the switch ther are little plastic pins. Open the switch and turn the little pns around and you should e fine. you cna e-mail me if you like and I can tell youhow to fix it...jams1@cox.net

Oct 08, 2010 | 2006 Nissan Frontier

1 Answer

I want to remove passenger side rear door panel because window is down and won't stay up


Hi,
Hi!!

Here is a little information on how window regulator works. Also step by step instruccions on how to remove and install the window glass.

Door Glass & Regulator Power Windows
Diagnosis & Testing
When the rear window lockout feature is enabled, the circuit is open and no voltage is supplied to the rear window switches. When the feature is not enabled, the circuit is connected to battery positive voltage. If this circuit is shorted to ground when the lockout feature is not enabled, the PWR WDO circuit breaker may cycle continuously OFF/ON until, either the lockout switch is pressed to open the circuit, or the circuit breaker is permanently damaged. All windows may be partially or totally inoperative while the fault is present.
Inspect for aftermarket devices which could affect the operation of the system. Inspect the easily accessible or visible system components for obvious damage or conditions which could cause the symptom. Faulty electrical connections or wiring may be the cause of intermittent conditions.
Removal & Installation
Window Motor & Regulator
  1. Position window approximately half way down in the door.
  2. Remove the interior trim panel.
  3. Remove the water deflector.
  4. Tape the window to door frame to prevent it from moving.
  5. Remove the three front door window regulator motor screws.
  6. Disconnect the electrical connector from the window regulator motor.
  7. Remove front side door window regulator motor.
  8. To install, reverse removal procedure.

Window Switch
Front
  1. Remove the front door pull cup screws and pull cup from the front door trim panel.
  2. Disconnect the electrical connectors from the front door power window control switch.
  3. Remove the front door window control switch using a small, flat-bladed tool at the side of the switch.
  4. To install, reverse removal procedure.

Rear
  1. Remove the rear door pull cup from the rear door trim panel.
  2. Disconnect the electrical connectors from the power window control switch.
  3. Remove the rear door window control switch from the pull cup using a small, flat-bladed tool at the side of the power window control switch to release the power window control switch retainer.
  4. Remove the power window control switch from the rear door pull cup.
  5. To install, reverse removal procedure.

Sep 07, 2010 | 2002 Buick Century

1 Answer

Mazda MPV: how to raise power window manually?


Hi,
I just had this problem with my driver door window. I took the door panel off and discovered that the motor was burnt out by testing with a meter.

I called around and found a motor at a junkyard for $135 dollars! I didn't bother looking at the price for a new one yet. Budget is very tight right now.

Like you I just wanted a way to get the window up until I could get around to replacing the part.

You can find out what I did with pictures here.

This is for the front driver side window. I did the same for the rear passenger side window and the steps are fairly similar.

There are few less steps to getting the panel off, but it was a little trickier to get the panel back on. (The key was to pull the bottom out and start at the front: Lower the forward part of the panel over the top of the frame first - while pushing firmly at the top of the panel).

The steps for disengaging the motor and raising the window with the motor re-engaged are almost the same. The only differences are that the motor is in a different position in the frame. It's down near the bottom of the frame - and seemingly inaccessible at first glance.

However, if you disconnect the motor from the frame and let it dangle on the regulator wires, you can pull it all the way through to the other port in the frame. That way, it turns out that, it was even easier to work with than the driver window motor.

Hope this helps.

May 11, 2010 | Mazda MPV Cars & Trucks

2 Answers

I have a 1994 jeep grand cherokee and the left passenger window has been "stuck", in the up position, for some time. Today, my daughter hit the power button and the window went down. Unfortunatly, it won't...


sounds like a loose wiring around the switch. take off the door panel accesorys untill u get to the switch panel check the connections and if good and problem persists then install another switch

Jan 06, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Help


That white peice is part of the window regulater. You have to replace the window regulater it comes with a new motor to.

Aug 17, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Window will go down, but not up.


If the window goes down, that says the motor is good. Being a DC motor it will run either direction. The window switch reverses the polarity. You can remove the door panel to get to the window motor connector and determine which wire is live in the down position of the switch. There is only 2 wires at the window motor. After you find out which wire is live for "down", using a 12v battery reverse the polarity by connecting a piece of wire from the battery positive to the window motor terminal that was NOT live in the "down" switch position before. And connect a piece of wire from the battery negative to the window motor terminal that WAS live in the "down" switch position before and the window will go up. Now being positive that the problem in not the motor. You will have to back track to the switches to determine what switch is the cause. Hope this helps. Good luck.

May 24, 2009 | 2004 Pontiac Montana

2 Answers

Rear power windows will go down not up


its the problem of control switch module in the drivers side and needs replacement to make it proper.

Jan 05, 2009 | 2000 Toyota Land Cruiser

Not finding what you are looking for?
2002 Ford Explorer Logo

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...