Question about 1993 Honda Accord

1 Answer

I need to replace broken lugnuts - 1993 Honda Accord

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 17,970 Answers

How to Replace Wheel Lug Nuts
(DIY Complexity: Easy / Time: 1.5 hours)

Parts:
1. Lug Nut


Tools:
1. Floor Jack
2. Jack Stand Set
3. Ball Peen Hammer
4. Tire Iron
5. Socket Set


Steps:
Step 1 Secure the vehicle on a solid level surface to ensure that it does not roll or lean when raised.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Break the lug nuts loose but do not remove. Using a floor jack, raise up the front of the vehicle.
o Tip: Using an aftermarket floor jack, instead of the original equipment (OE) jack, can make the job easier and safer. Verify the condition of the floor jack before use.

Step 3 Secure the vehicle with jack stands on both sides for safety before starting any work. Do not rely on the jack to hold the vehicle up while working.
o Tip: The pinch welds or the frame rails are the two best locations for vehicle support.

Step 4 Remove the lugs nuts. Inspect the threads on the wheel studs.

Step 5 Install the new lug nuts by hand making sure they thread properly.

Step 6 Tighten each lug nut in a star pattern. Lower the vehicle to the ground and torque the lug nuts to the manufacturer’s specifications.
o Tip: Refer to the owner's manual for the exact location on the vehicle.

Step 7 Road test the vehicle to verify lug nut repair.


I really hope help with this (remember comment and rated this post).

Posted on May 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Im trying to replace my passenger side front lugnuts


jack up vehicle, remove tire, Beat on broken lug till it falls out- install new lugnut (will be pressure fit) replace tire and tighten nut....make sure you tighten it 2 times at first then after 50 miles check it again.

Dec 09, 2013 | 1997 Plymouth Grand Voyager

1 Answer

How do you replace tire bolts and lugnuts


YOU DON'T SAY WHAT TYPE OF VEHICLE YOU OWN. SO , THIS IS A RATHER GENERIC TYPE ANSWER. THE HUB OR AXLE SHAFT HAS THE WHEEL STUDS PRESSED INTO IT. THE LUG NUTS FASTEN TO THEM. TO REPLACE A BROKEN STUD YOU MUST USE A PRESS OR A DRIFT PIN AND A HAND SLEDGE HAMMER TO KNOCK OUT THE BROKEN STUD. YOU CAN REPLACE THE BROKEN STUD THE SAME WAY. THE PROBLEM IS YOU WILL PROBABLY HAVE TO REMOVE THE AXLE OR THE HUB, OR THE DISC TO REMOVE AND REPLACE THE STUD. AN EASY TASK IT YOU HAVE THE CORRECT TOOLS. IF NOT JUST TAKE IT TO A REPUTABLE TIRE STORE AND THEY PROBABLY WILL REPLACE IT CHEAPER THAN YOUR LOCAL GARAGE WILL. BE PREPARED TO SHELL OUT $45.00 TO REPLACE A $3.00 STUD.

Oct 22, 2011 | 2004 Ford Explorer

1 Answer

Need to romove and replace sheared lugbolt on rear driver side wheel hub


remove tire...if it has disc brakes remove caliper/pads and rotor...if it has a drum break remove drum..Now take a punch and hammer and hit the center of the lugnut stud untill it pops out the back.put the new one in and get it tight with the lugnut.Replace brakes and tire and tighten that lugnut until it stops.Then check it in 500 miles

Jun 06, 2011 | 1998 GMC Jimmy

1 Answer

I need to replace left front lugnut stud. what do i need to remove to get the outer part of the rotor off to replace the broken stud?


The rotor is bolted to the wheel hub from the backside. To get at those bolts you will need to remove the CV axle from the wheel hub. If you've never removed a CV axle before I suggest getting a repair manual for the vehicle (from an auto-parts store) or take it to a mechanic that you trust.

Aug 06, 2010 | 1991 Honda Accord

1 Answer

TIRE IS FALLING OFF THREADED STUDS BROKEN


Replace all the studs on that wheel and it's twin on the other side. To do this, you have to turn the wheel to where the stud can come out from the inside, and use a hammer (or hammer and punch for the broken ones) to push them out the back of the wheel. You'll have to turn the wheel for each one. To put the new ones in, slide it into the hole that's been vacated, and use a lugnut to pull it in. Flip the lugnut so the the cone shaped end is out (upside down), and tighten it until it pulls the stud all the way on. Take the nut off, turn the hub, and do the next one in the same way. Make sure that you do the other side too, because it's been subjected to similar loads, and is likely ready to fail as well. Mount the tires, drive the car around a little, taking a few curves, but lightly. Stop, and retorque the lugnuts. Take it on another drive, but harder in the curves, and retorque the lugnuts. You are then finished. Just a note: whenever you retorque the lugnuts, loosen first, then tighten. This keeps you from overtightening them.

Jun 04, 2010 | 1996 Buick LeSabre

1 Answer

My wheel studs is breaking off one by one like every 250 miles but first studs would break from the middle of the lugnuts half of broken stud would fall out the lugnut leaving the lugnut hanging on by...


you migh need just bigger lug nuts there easy to replace just remothe the rotor hamer the old studs out slide in the new one just as if you were puting on the rim with out acually put in it on so it will set even with the others and thats it

Nov 06, 2009 | 2003 Dodge Durango

1 Answer

How do u replace lugnut bolt on front tire 2000


Hi,
The lugs are generally pressed into the rotor. They have a fluted shank which prevents them from turning when you torque the lugnuts. If you are going to do this job yourself, they can be driven out with a punch. The new replacement can be drawn into position with the lugnut, but you might need to utilize some spacers and washers to do this.
I've performed this operation before with the rotor still on the vehicle.
I hope this helps... Good luck!

Oct 22, 2009 | 2000 Dodge Caravan

2 Answers

My other half has broken his locking wheel nut key for his escort gti where can iget a replacement


you have to call the manufacturer and give the the number on the lugnut and they will sell you another. about $25. Been there done that. Another option is to buy a socket that you hammer onto the lugnut. It grips the lugnut and you can then use a ratchet to get it off. you do have to replace the lugnuts after doing this. the socket was $8 at Oriellys.

Sep 30, 2009 | 1998 Ford Escort

1 Answer

2002 grand caravan front twisted off lugnut


front rotor is slip on design..just may be stuck to hub..remove caliper and caliper bracket..remove rotor knock broken stud out with hammer/punch..install new stud with washers and nut

Apr 15, 2009 | Dodge Caravan Cars & Trucks

Not finding what you are looking for?
1993 Honda Accord Logo

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...