Question about 1997 Mitsubishi Galant

Open Question

Need 1997 Galant V6 6A13 ECU pin out

Need 1997 Galant V6 ecu pin out

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
MrScary66613
  • 1990 Answers

SOURCE: i need to reset my

Locate your Fuse Panel and Find the Fuse Marked ECU, Pull the Fuse for 2 or 3 Minutes then Replace. will Clear and Reset.

Posted on Jan 03, 2009

Ad
  • 234 Answers

SOURCE: ECU Location on 2001 Galant ES

i think it is under the dash at the side passenger

Posted on Jun 05, 2009

  • 234 Answers

SOURCE: i need a new front ecu do you know of any other

i think if u open it u p the chip is removable

Posted on Oct 10, 2009

  • 1 Answer

SOURCE: I have a 1997 Mitsubishi Galant with rough idle

I am having the same issue on Mitsubishi Galant 02. Clattering on acceleration, herky jerky idle. Pulled a code multiple cylinder misfire. My mechanic's diagnosis is bad valve cover gasket causing oil to seap into the spark plugs and bad timing belt, which I have not replaced at 150k miles. I do however know my fuel injectors do need cleaning, he hasn't ruled that out either. Have you pulled any code on it? I have read on engine knock sensor going out on some of these also. Hope this helps some.

Posted on Oct 22, 2010

  • 14585 Answers

SOURCE: My galant has been idling roughly and vibrating

I would be leary about just replacing the ecu.especially if you can disconnect it and ir runs fine. Did they tell you what error messages there were? This would be helpful to know

Posted on Nov 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ecu pin out 2mz-fe auto...toyota windom...


[PDF]WIRING DIAGRAM BY MODEL - Apexi

www.apexi-usa.com/manuals/electronics/neo_diagram.pdf
TOYOTA. Table of Applicable Models. ..... The orientation of the ECU depends on the vehicle with ECU pins. Install the ECU fully checking the .... 2MZ?FE. '97.5?'02.1. VEROSSA. JZX110. 1JZ?GTE. '01.8?'04.4. L. T10?b. HW?23.

1997 Camry V6 ECU Pinout - Toyota Nation Forum : Toyota Car and ...

www.toyotanation.com/.../97568-1997-camry-v6-ecu-pinout.html

Sep 19, 2005 - 10 posts - ‎3 authors
So as the title says, Anyone know the pinout to help with a SAFC install? ... look in the apexi install manual, it is t8-f. the same as the 2mz-fe ... Perkins 99 Camry 1mz Build
15 posts
Nov 28, 2012
1mz-fe to 2mz-fe
15 posts
Feb 25, 2010
SAFC Wiring Pin-Out for 94 1MZ-FE - Toyota Nation ...
8 posts
Feb 8, 2008
1996 1mz ecu pinout needed and question
10 posts
Feb 18, 2006
More results from www.toyotanation.com

Dec 03, 2015 | Cars & Trucks

1 Answer

NO SPARK ON 1997 MITUBISHI GALANT


That generation of Mitsubishi had an issue with faulty electronics in the ECU. Try and source a new one or many folks refurbish them with a lifetime warranty. Hope that helps a little.

Oct 17, 2012 | 1999 Mitsubishi Galant

1 Answer

Mitsubishi galant es ecu location images


What coloure is the wire that ignite the ecu

Jun 06, 2012 | 2001 Mitsubishi Galant

1 Answer

My ecu is making my effecting my transmission can i program another ecu manually


need more specific information on problems being caused by ecu. Has tcu been checked?

Sep 18, 2011 | 2002 Mitsubishi Galant

1 Answer

The check engine light stays on everytime. ECU has alrady been replaced.


HAVE VECHICLE SCANNED AGAIN YOUR ECU COULD BE WRONG ONE OR YOU NEED NEW ECU PROGRAMMED TO THE VECHICLE.IT DONT RECOGNIZE VECHICLE.

Nov 26, 2010 | 1995 Mitsubishi Galant

1 Answer

Instructions for replacing 1997 Jeep Wrangler 6cyl


Its an easy job! Disconnect the battery first! That's very importand! Then disconnect the wiring pack from the ECU. Some models are equipt with snap-systems, other with a screw-system to remove the wiring connector from the ECU. If done, there are three or four screws that hold the ECU in place with the body. Remove the screws and you hold the ECU in your hands. To buy a new or rebuilt ECU, reffer to the numbers shown on the label at your Wranglers ECU in combination with the V.I.N. To connect the new ECU with the wiring pack, be careful with the connector! You need to put him in the right position to connect with the ECU. Do it slow and make sure the connector fits to all points. Otherwise you'll bake some contacts inside the connector.

Oct 23, 2009 | 1997 Jeep Wrangler

2 Answers

Electrical diagram


Hi,

Might this help?
They were originally posted here and here.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Aug 16, 2008 | 1992 Toyota Celica

Not finding what you are looking for?
1997 Mitsubishi Galant Logo

Related Topics:

270 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...