Question about 1992 Jeep Cherokee Briarwood

1 Answer

Just wondering where the knock sensor is located in a 1992 jeep cherokee 4.0 There is a sensor on the left rear of the head that is burnt up and I am wondering if this is it.

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Bump. looking for same answer.

Posted on Sep 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is crank shaft position sensor located on 1997 jeep grand cherokee


CRANKSHAFT POSITION SENSOR LOCATION FOR 4.0L ENGINE IS ON TRANSMISSION BELLHOUSING AT THE LEFT REAR OF THE ENGINE. FOR 5.2L ENGINE CRANKSHAFT SENSOR LOCATED ENGINE BLOCK BEHIND THE RIGHT CYLINDER HEAD.

Dec 11, 2010 | 1997 Jeep Grand Cherokee

1 Answer

Locate crank shaft sensor on 1998 jeep grand cherokee


4.7L ENGINE CRANKSHAFT SENSOR LOCATED ON THE ENGINE BLOCK ABOVE THE STARTER. ON THE 4.0L ENGINE CRANKSHAFT SENSOR LOCATED TRANSMISSION BELL HOUSING AT THE LEFT REAR OF THE ENGINE. THE 5.2L 5.9L CRANKSHAFT SENSOR LOCATED ON THE ENGINE BLOCK BEHIND THE RIGHT CYLINDER HEAD.

Nov 26, 2010 | 1998 Jeep Grand Cherokee

2 Answers

Where is the knock sensor located on my 92 Jeep Cherokee 4.0L straight 6 4WD?


I don't see the knock sensor on the 4.0L engine. --- COMPONENT LOCATIONS Fig. 1: Electronic engine control component locations - 2.5L engine shown 91074g07.gif
Fig. 2: Overhead view of the (A) automatic idle speed motor, (B) MAP sensor, (C) crankshaft position sensor wiring harness, (D) air temperature sensor, and (E) throttle position sensor - 1992 Cherokee with the 4.0L engine shown 91074p15.jpg
Fig. 3: Electronic engine control component locations - 4.0L engine shown 91074g08.gif
Fig. 4: Electronic engine control component locations - 5.2L and 5.9L engines (Part 1 of 2) 91074g05.gif
Fig. 5: Electronic engine control component locations - 5.2L and 5.9L engines (Part 2 of 2) 91074g06.gif
prev.gif next.gif

Sep 30, 2010 | 1992 Jeep Cherokee Briarwood

1 Answer

Need color of wiring a 1992 jeep larado radio


Hello
1992 Jeep Wrangler Car Stereo Radio Wiring Diagram
Car Radio Constant 12V+ Wire: Pink
Car Radio Switched 12V+ Wire: Purple/White
Car Radio Ground Wire: Black
Car Radio Illumination Wire: Blue/Red
Car Radio Dimmer Wire: Red/Black
Car Radio Antenna Trigger: N/A
Car Radio Amp Trigger Wire: N/A
Front Speakers Size: 4′ x 6′
Front Speakers Location: Dash
Left Front Speaker Wire (+): Gray
Left Front Speaker Wire (-): Yellow
Right Front Speaker Wire (+): White/Red
Right Front Speaker Wire (-): Black/Red
Rear Speakers Size: 4′
Rear Speakers Location: Rear Roof
Left Rear Speaker Wire (+): Gray/White
Left Rear Speaker Wire (-): Brown/White
Right Rear Speaker Wire (+): White/Black
Right Rear Speaker Wire (-): Brown

Jul 14, 2010 | 1992 Jeep Cherokee Limited

1 Answer

Location of knock sensor?


Look under exhaust manifold on drivers side, closer to rear of engine, mounted on engine block.

Keep in mind that the knock sensor is a tuned piezoelectric crystal transducer that is located in the cylinder head. The knock sensor provides the MCU with an electrical signal that is created by vibrations that correspond to its center frequency (5550 Hz). Vibrations from engine knock (detonation) cause the crystal inside the sensor to vibrate and produce an electrical signal that is used by the MCU to selectively ****** the ignition timing of any single cylinder or combination of cylinders to eliminate the knock condition.

This and other details can find in the Grand Cherokee Service Manual.

Good luck (remember rated this).

May 31, 2010 | 1996 Jeep Grand Cherokee

1 Answer

Where is the knock sensor at


Located on side of engine block.

Feb 25, 2010 | 1992 Jeep Cherokee Briarwood

1 Answer

I have a knock in motor


What is your QUESTION? If it is knocking, it needs a head or a motor.

Aug 12, 2009 | 1992 Jeep Cherokee Limited

1 Answer

Diagram or location of knock sensor


Look under exhaust manifold on drivers side, closer to rear of engine . mounted on engine block.

Jun 01, 2009 | 1995 Jeep Cherokee

Not finding what you are looking for?
1992 Jeep Cherokee Briarwood Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...