Question about 2007 Toyota Corolla

Open Question

Replace license plate bulb on 2007 corrolla - 2007 Toyota Corolla

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 65 Answers

SOURCE: I have a 2004 Toyota

You have to remove the rear door inside panel.First thing is to remove the top and side interior trim panels,they just pop out by prying them away after they are out the metal retaining clips sometimes stay in the door,pull them out and put them on the plastic panel before reinstalling.Then the strap that you use to close it has a cover on it that you have to push up to get off then remove the 10 mm bolt that holds the strap.Then pry the panel away from the door I think that the bottom has two hooks on it which means that the top needs come off first so you can lift the panel hooks out of the slots.Once the panel is off you will see the bulbs they twist out and you have to pull the bulbs out.Good luck

Posted on Nov 29, 2008

Ad
  • 2 Answers

SOURCE: how to replace license plate light bulb

open back hatch in the center there is a rectangle shaped piece of plastic pop it out and you will see the wire on the back of the bulbs

Posted on Dec 04, 2008

  • 1 Answer

SOURCE: Light Bulb Replaement

I just replaced the license plate lamps on my 2004 Deville DTS.
Lamp is PC195. Lamp PC168 will also work, (it was in my car for the last two years), but it is a brighter bulb than needed.

You pop out the lamp holders by pushing (sliding)the right side towards the left. That little push will unhook plastic tabs from the sheet metal and the right side of the lamp holder will release from the trunk. See the attached photo.

To push the lamp holder, I used a narrow putty knife covered with masking tape. A screwdriver will work as well. The masking tape protects the paint from scratches.

Posted on Jan 08, 2009

  • 840 Answers

SOURCE: 2002 license plate bulbs

its real simple look at the license plates then look up you will see 2 screw per lamp / unscrew them and slide remove its a 194 bulb so get some ready then replace and put back / Please rate my response thank you very much

Posted on Feb 02, 2009

  • 94 Answers

SOURCE: how to replace the license plate blub

open the trunk and remove the back panel in the trunk could be a couple of clips or a few screws holding the panel on one you remove the panel you should have easy access to the bulb just twist and remove. or on some avalons you need to pry the lens off the light to replace it then the lens will click back into place with a little push

Posted on Mar 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 chevy equinox license plate light won't work after bulb and fuse replacement


Do the park lamps work ? license plate lights get power from same fuse ! Check ground wire ! use a volt meter an do voltage drop test ! Voltage Drop Testing The fuse for the license plate lights is in the under hood fuse box -engine compartment ! fuse #12 RT PRK LAMP 10Amp .

May 23, 2015 | 2007 Chevrolet Chevrolet Equinox LT

1 Answer

License plate lights out 2007 nissan sentra


easiest check fuses for blown fuse.
Inspect wiring to see if they are unplugged
replace bulbs even if they look good.
Bottom left of dash under steering wheel locate sunglass holder, open holder and then pull up fusebox underneath

Mar 08, 2013 | 2007 Nissan Sentra 2.0 SL Sedan

1 Answer

How to replace License Plate Bulb '96 Jeep Grand Cherokee Limited


Hi Timmy:

Check this procedure from Repair manual...


LICENSE PLATE LAMP - REMOVAL
(1) Remove screws and license plate lamp visor from liftgate (Fig. 10).
(2) Remove bulb from lamp socket.

INSTALLATION
(1) Install a bulb in lamp socket.
(2) Position license plate lamp visor on liftgate and install screws (Fig 10).


4_28_2012_5_22_57_pm.jpg


Hope this helps.

Apr 28, 2012 | 1996 Jeep Grand Cherokee

1 Answer

How do I change the license plate bulbs?


Look under the bumper, you should find the light bulbs in a harness. To release them, twist the bulbs until the are unlocked from the harness. Pull the bulb out and replace it.

Apr 17, 2011 | 2007 Hyundai Accent GS Hatchback

1 Answer

I need to replace the bulbs above the license plate on my 2002 eldorado how do you replace them....get at the old bulbs


Hello: Remove the license plate, then remove the screws on the chrome piece behind the license plate and the you can access the bulbs.

Nov 24, 2010 | 1999 Cadillac Eldorado

1 Answer

How can I change the rear license plate lights on a 2007 Accent hatchback? Besides two screws there are also two clips holding the trim piece above the license plate in place.  Unsure if this is the...


there are clips on the side of the bulb holders that squeeze together then push out to reveal the bulb holder. you can locate these by opening the boot lid, and on most mosels removing the plastic surround. you can then see the holders inside. just hold finger and thumb at each end and gently squeeze the clips and push out the holder to replace buls

Mar 12, 2010 | 2007 Hyundai Accent GS Hatchback

1 Answer

License plate bulb needs replacing


Remove license plate. Unscrew the screws on the underside of the bumper. Slide the lights back toward the trunk and then down through the opening. Unscrew bulb and replace with a new one.

Reverse steps to reinstall the lights.

Feb 06, 2010 | 2003 Chevrolet Impala

1 Answer

How do I replace the license plate bulbs?


The license plate lights are accessed by unscrewing the lens. The backup lightbulbs are accessed with the trunk lid open, behind the cover.

Jan 13, 2010 | 1992 Honda Accord

1 Answer

2007 Pontiac G6. Rear license plate bulb socket dead


park lamp and license plate share same fuse.check park lamp fuse.if fuse good you have ground wire problems.

Nov 30, 2009 | 2007 Pontiac G6 GT Convertible

1 Answer

1999 Dodge Neon rear license Plate bulb


LICENSE PLATE LAMP BULB
REMOVAL
  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Oct 08, 2009 | 1999 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...