Question about 2007 Chevrolet Cobalt Coupe

Open Question

I have a B0012 B0013 code on my Chevrolet Impala 2008. Driver frontal deployment loop stage 1. The car was involved in an accident and the driver airbag deployed. I replaced the airbag, clockspring, and both belts and the module. Is there anything else that needs to be changed? I've checked the fuse and it's good, checked the wires and don't see nothing visually bad. Any ideas? thanks a lot for any help.

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 400 Answers

SOURCE: B0012 SAYS FRONTAL PASSENGER DEPLOYMENT LOOP. WHAT

B0012 is a fault on the DRIVERS side, you sure you read the code right?
If it is a B0012 then any of the wiring could be suspect the coil or the air bag it's self. I have seen a couple of cars coming with this code and I found the wires coming out of the air bag in the steering wheel to be rubing where they go through the steering wheel into the colume, may want to check there first.
Report back if the code is something else so we can try and assist you.

Posted on Oct 18, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Service Air Bag light on


DTC B0058 Right Front/Passenger Pretensioner Deployment Loop Open.
The passenger seat belt pretensioner deployment loop consists of a seat belt pretensioner-RF and the seat belt pretensioner-RF high and low circuits. A shorting bar used within the seat belt pretensioner connector shorts together both the seat belt pretensioner high and low circuits when the connector is disconnected. This will help to prevent unwanted deployment of the pretensioner during servicing. During a frontal crash of sufficient force the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy the seat belt pretensioner. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If a malfunction is detected, a diagnostic trouble code (DTC) will be stored in memory.
DTC B0084 Left Front/Driver Seat Position Sensor Circuit
The inflatable restraint seat position sensor (SPS) is used to determine the proximity of a front driver or passenger seat position with respect to the frontal air bag. The SPS interfaces with the sensing and diagnostic module (SDM). The state of the SPS allows the SDM to disable stage 2 of the frontal air bag for a front seat that is forward of a forward/rearward point in seat track travel. The SPS is a hall effect sensor that is mounted on the inside seat track of both the driver and passenger seats. The seat track includes a metal bracket that shunts the SPS magnetic circuit creating 2 states of seat position. The shunted state represents a rearward seat position. The non-shunted state represents a forward position. The SPS provides 2 current ranges, one range for the shunted state and a second range for a non-shunted state. These 2 states are inputs to the SDM. State 1 (shunted) being the rearward threshold and state 2 (non-shunted) being the forward threshold. When the SDM receives input from a SPS that state 1 threshold is reached (seat is rearward) the SDM will not disable stage 2 deployment, if required by the deployment sensors. When state 2 threshold is reached (seat is forward) the SDM will disable stage 2 deployment on the side the seat is forward. The SDM monitors the SPS circuit and if a fault is detected the SDM will set codes B0083 or B0084 and defaults to disabling stage 2 frontal deployment. This will only default on the side of the vehicle the sensor has a fault. Its important to understand that the SPS is secondary to the passenger presence system (PPS) and the manual instrument panel (I/P) module disable switch. If either one of these devices are in the disable mode the passenger air bag will not deploy regardless of the SPS status.
You should take this to a qualified repair Shop ! Takes special tools to test .

Feb 26, 2016 | 2006 GMC Envoy

1 Answer

What does the code b0026 mean on my 2009 buick lacrosse?


DTC B0026: Driver Frontal Deployment Loop (Stage 1) Open
It has to do with air bag system
B0026 Stage 1 or B0044 Stage 2 ?€¢
The steering wheel module stage 1 or stage 2 high circuit is less than 2.4 volts and the steering wheel module stage 1 or stage 2 deployment loop is more than 6 ohms for 500 milliseconds.


?€¢
The steering wheel module stage 1 or stage 2 deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.



has to do with

Jun 30, 2015 | 2009 Buick LaCrosse

1 Answer

2005 Silverado regular cab sets b0017 code and airbag light comes on and off frequently. Any help?


Meaning of code 1 Driver knee deployment loop 2 Passenger frontal deployment loop open
Get to dealer have fixed soon will not be protected in crash airbag's won't deploy

Apr 21, 2015 | 2005 Chevrolet Silverado

1 Answer

2004gmcyukonb0026


DTC B0026 LF/Driver Frontal Deployment Loop (Single Stage or Stage 1) Open circuit.
WARNING! Do not attempt to repair this without factory manual to explain disarming the system.

May 16, 2012 | Cars & Trucks

1 Answer

2009 chevy impala left front side deployment loop resistance B0014 above threshold


the following link covers yours reqest The driver frontal loops 1 and 2 are the loops to the steering wheel air bag. The SDM(sensing and diagnostic module for the air bag) is seeing these circuits as open. There is a bullitin for problems with a loose connection for the yellow connector behind the left kick panel(right behind the e brake and hood release). I would remove the kick panel, and disconnect and reconnect the connector a couple times. See if the light goes out. Or wiggle and move the connector with the key on, as the light should go out if it makes good connection. If it does go out you need to replace this connector. Good luck.

#05-09-41-001B: Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (Inspect/Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222) - (Jun 2, 2008)

Subject:Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (DTC) B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 (Inspect and/or Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222)
Models:2003-2006 Cadillac Escalade Models
2003-2006 Chevrolet Avalanche, Suburban, Tahoe
2003-2007 Chevrolet Silverado (Classic Only)
2003-2006 GMC Yukon, Yukon XL, Yukon Denali, Yukon Denali XL
2003-2007 GMC Sierra (Classic Only)


This bulletin is being revised to add the 2007 model year for pickups and change a part number. Please discard Corporate Bulletin Number 05-09-41-001A (Section 09 -- Restraints).

<A href="#ss1-2146754">
Condition
Some customers may comment that the Service Supplemental Inflatable Restraint Light is on.

Diagnosis with a scan tool may indicate a DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

<A href="#ss2-2146754">
Cause
The most likely cause of any one of the following DTCs: B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 is improper connection/high resistance in the IP harness to inflatable restraint module connector C221 and/or C222.

<A href="#ss3-2146754">
Diagnostic Information

DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 will set when one of the following conditions occur:
• The SDM detects the air bag module deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.
• The SDM detects that the voltage at the air bag module high control is less than 2.4 volts and deployment loop resistance is 6 ohms or greater for 500 milliseconds.
• For additional diagnostic information, refer to DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 in the appropriate SI Document.
<A href="#ss4-2146754">
Correction
DO THIS

Don't Do This

Test for proper connection/high resistance at connector C221 and/or C222.

DO NOT replace SIR system components prior to testing for proper connection/high resistance in C221 and/or for DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

Caution: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling Zones. Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs.



Important:
The IP harness to inflatable restraint module connectors C221 or C222 is NOT located at the base of the steering column.
• C221 (4 Cavities) -- I/P Harness to Body Harness, behind the left kick panel
• C222 (4 Cavities) (w/o HP2) -- I/P harness to body harness, behind the right kick panel
• C222 (4 Cavities) (w/HP2) -- Behind the left side I/P access panel
• Refer to the Master Electrical Component List for additional location information.


  • <LI type=1>Remove the appropriate side door sill plate. <LI type=1>Remove the appropriate side hinge pillar panel. <LI type=1>Locate the IP harness to inflatable restraint module yellow 4-way connector C221 or C222. <LI type=1>Inspect the IP harness to inflatable restraint module connector C221 or C222 for proper connection. <LI type=1>Disconnect and reconnect the IP harness to inflatable restraint module connector C221 or C222 THREE times. <LI type=1>Clear the DTC and road test the vehicle. • If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES NOT reset, no additional repairs are necessary. Continue with step 10.
    • If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES reset, the most likely cause is high resistance in the IP harness to inflatable restraint module connector C221 or C222. Continue with the next step.
    <LI type=1>Replace the appropriate connector C221 and/or C222, P/N's 15306186 and 88987998. Refer to SIR/SRS Wiring Repairs (SI Document ID #325229). <LI type=1>Road test the vehicle and confirm that the repair is complete. <LI type=1>Install the driver's side hinge pillar panel.
  • Install the driver's side door sill plate.
<A href="#ss5-2146754">
Parts Information
Part Number

Description

Qty

15306186

Connector (4-way Female, w/Leads)

1

88987998

Connector (4-way Male, w/Leads)

1 Service Airbag Have Codes Ask the GM Technician

May 01, 2012 | Chevrolet Impala Cars & Trucks

1 Answer

What does air bag code 43 mean?


The driver frontal loops 1 and 2 are the loops to the steering wheel air bag. The SDM(sensing and diagnostic module for the air bag) is seeing these circuits as open. There is a bullitin for problems with a loose connection for the yellow connector behind the left kick panel(right behind the e brake and hood release). I would remove the kick panel, and disconnect and reconnect the connector a couple times. See if the light goes out. Or wiggle and move the connector with the key on, as the light should go out if it makes good connection. If it does go out you need to replace this connector. Good luck.

#05-09-41-001B: Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (Inspect/Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222) - (Jun 2, 2008)


Subject:Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (DTC) B0013, B0014, B0017, B0043, (Inspect and/or Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222)



Models:Tahoe

• The SDM detects the air bag module deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.

• The SDM detects that the voltage at the air bag module high control is less than 2.4 volts and deployment loop resistance is 6 ohms or greater for 500 milliseconds.

Apr 22, 2012 | 2003 Chevrolet Tahoe

1 Answer

My air bag code on 2007 chevy cobalt is b0012 and b0013


Hi, Below are the detail on codes : Code b0012=> Driver frontal deployment loops stage 1 resistinal below threshold Code b0013=> Driver frontal deployment loops stage 2 resistinal below threshold And please get it fixed at dealer.
Regards

Jan 30, 2011 | 2007 Chevrolet Cobalt Coupe

1 Answer

What does code B0026 dr frontal deployment loop[stage 1 open] mean


This is usually due to an airbag deployment. It's the code for the front left circuit (driver's side). Most likely, the driver's side airbag deployed and the bag and module were replaced, but the module circuit ring in the column wasn't replaced. When the module senses the need to deploy, it sends a signal to the ring opening the line for the current to flow and causes the bag to deploy. Problem is, the circuit stays open, and casues a fault code. The unfortunate part is, until the curcuit is replaced, the SRS system in inoperable and will not deploy again in the event of an accident. You'll have to have the steering wheel pulled to service this item and should be done by a certified technician. It can be expensive, but worth the price of your safety.

Jan 08, 2010 | 2003 GMC Yukon XL

1 Answer

B0012 SAYS FRONTAL PASSENGER DEPLOYMENT LOOP. WHAT


B0012 is a fault on the DRIVERS side, you sure you read the code right?
If it is a B0012 then any of the wiring could be suspect the coil or the air bag it's self. I have seen a couple of cars coming with this code and I found the wires coming out of the air bag in the steering wheel to be rubing where they go through the steering wheel into the colume, may want to check there first.
Report back if the code is something else so we can try and assist you.

Oct 18, 2009 | 2007 Chevrolet Cobalt Coupe

Not finding what you are looking for?
2007 Chevrolet Cobalt Coupe Logo

Related Topics:

2,020 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...