Question about 1999 Dodge Ram 2500 4WD

1 Answer

Will not start odometer display shows code p-1693

Posted by on

  • cdfred May 15, 2010

    yes going about 40 mph truck droped to idle. when youput foot on excellerator it starter missing and running rough would not go over 1000 rpm. would idle fine, shut it off got code p-1693 restarted once same thing waited on tow truck for 45 minites and it would not refire would try but would not go like starving for fuel.

  • cdfred May 18, 2010

    code p-1693 only means that there are codes in the cummings computer,thats all that means. When these codes were checked it was determined that the injection pump had failed. Then lift pump was checked and it was boarderline on output. Not sure if liftpump caused injection pump failure or not. Both pumps were replaced.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 957 Answers

P1693 has to do with a comunication problem between the ECU and the EEPROM. This code is rarely seen. You may need a computer but I'm saying, check other things first. You may have a blown fuse or bad wire or connection. Did this problem happen out of the blue?

Posted on May 15, 2010

  • larry blais
    larry blais May 15, 2010

    I would guess that you need a fuel-pump (from the symptoms) but The stored code makes me think that power was lost. Well good-luck and please let me know what the repair was.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Shift indicator lights up but does not display which gear I am in.


Odometer/Gear Shifter (PRNDL) Display FIX - GMC/Chevy ...

? 4:15
https://www.youtube.com/watch?v=-PQ-x11Vjng
Jan 24, 2012 - Uploaded by EricTehRedneck
Odometer/Gear Shifter (PRNDL) Display FIX - GMC/Chevy ...grease, it does in fact help insulate electrical connections but imnot sure lithium would help. .... i have a 2000 Chevy Astro van the park indicator goes out when you start ... volts but now the battery light stays on and the transmission will not shift ...

GM Electronic Gear Indicator and Tripometer Odometer ...

? 5:47
https://www.youtube.com/watch?v=jTQIVS_uB4g
Aug 11, 2010 - Uploaded by zcomputerwiz
Didn't light up anymore. ... Symptoms: PRND321 and Tripometer/Odometer no longer light. ... 2002 which the odometer and shift indicator do not work no more. ... But before taking the dash out I would like to know how to remove those .... Instrument cluster gear select blank screen solder fix Chevrolet GM ...

Repair the odometer/PRND321 LCD display on a '99-'06 ...

www.instructables.com/.../Repair-the-odometergear-select-L...

InstructablesIn this Instructable, I will show you how to repair odometer/gear select ... Repair the

Feb 09, 2016 | 1998 Chevrolet Blazer

1 Answer

1998 dodge diesel 24v ,1693 engine code


yes .
still i will provide you the link
for this type of problems
http://www.automotix.net/autorepair/repairtips/

Aug 14, 2008 | 1998 Dodge Ram 2500 2WD

1 Answer

When started, why doesn't it show the miles on the odometer?


probably you have some other feature displayed and if it is like my ford the odometer can't display if another option has been displayed. Like a limited number of display items are available at anyone time so other display items get turned off . I suspect !

Dec 31, 2015 | 2006 Ford Focus

1 Answer

Ecu error code 121. p code 1693


go on line to the following sites ask about the error message.

www.ask.com
www.info.com
www.wiki.org
www.about.com

type the following : ecu error code 121.p code 1693 mean

thank you rod

Mar 04, 2015 | 2002 Dodge Ram 3500 Truck

3 Answers

How do I do a Diagnostic System Check? Is this


If you can visit one autozone shop, they can read or scanning your OBD codes.

Codes are displayed on digital odometers on newer models. On many 2001 and newer models, holding in the trip odometer reset button while turning the key to RUN will start a self test, with a readout on the odometer. It will also activate all instrument panels, one at a time. We do not know if this will show computer codes, or whether it only tests the instrument panels. At the end, it may show a few odd codes that are firmware versions and not error codes.

On most cars, the codes will read out if the engine light is on - all you have to do is put the key into the RUN position.

Normally, to get codes, you put the key on OFF and then rapidly do OFF-ON-OFF-ON-OFF-ON (on some cars you have to do four or five, not three, OFF-ON cycles). On our test 2002 car, the key did not go back to unlock, so it was ACC-ON-ACC-ON-ACC-ON.

  • You may have to have the parking brake firmly set for the codes to show! (Thanks, Steven Midway)
  • Jon Yoon: The 1998 Caravan does the same check engine light code trick, but it also does an instrument diagnostic check if you hold the trip and reset buttons and turn the key to the run position and wait 5 seconds. This helped me figure out that my input and output speed sensors were broken but the actual speedometer dial could move.
  • For the 1999 Jeep Grand Cherokee and up, you do the switching the key on and off 3 times, but not quickly. You turn it to on so the odometer turns on, turn it off, and then back on, wait for the light to turn on, etc. On the fourth time you'll get a code, or you'll get the word "done." (Monica MacDonald)
A loose gas cap may light up the Check Engine light! (Thanks, Lyn Clark)
  • When the computer indicates major failure, it can activate Limp In mode, which guesses about data to compensate for sensor failure, allowing you to get the car to a mechanic. One major symptom of this is the transmission sticking in second gear. This is a feature!
  • 2002 Ram, put transmission in neutral, parking brake on, then do the acc-run key sequence 3 times.
  • Dan Stewart wrote about the 1999+ Voyager/Caravan with digital gear selection display:
    • There are 2 functions that can be accomplished with the key-on sequence. Get Diagnostic Trouble Codes by placing the key into the ignition. Push and hold the both the "Trip" and the "Reset" buttons with the left hand and turn the key to the "ACC" position (first position between "LOCK" and "RUN"). Continue to hold both buttons in and count to 5. Release both buttons, display should read trip mileage instead of total mileage. Push the "TRIP" button and the odometer will display DTC'S in rotating sequence instead of displaying total mileage.
    • The second function is an instrumentation diagnostic. Place key into ignition, press and hold both "TRIP" and "RESET" while turning the key to the "RUN" position. Continue to hold both buttons in until odometer displays "CODE". Release buttons. The display will then display "999". Afterward it will display "CHECK 0" and test the analog gauges. It will then display "CHECK 1" and test the digital displays

RESET THE COMPUTER
Normally the computer will eventually reset itself; you can also use a scan tool. (See our transmission repair page for information on resetting the computer's transmission information.) Disconnecting the battery for a few minutes generally resets the computer, though it also means losing clock settings.
Sid Willoughby wrote: “To clear the check engine light on a 2002 Dodge Ram once the problem is resolved. Start the engine and drive forward then in reverse (you only have to move the truck a few feet in each direction) the turn the ignition off. Do this sequence three times. When you start the vehicle the fourth time the check engine light should go out.” (This procedure may well work on other vehicles.)

CODE LIST 2001 which covers some vehicles from the late 1990s as well as newer ones. It shows the longer codes starting with the letter P.

Hope this help (remember comment and rated this).


Apr 09, 2010 | 2001 Dodge Caravan

1 Answer

Need codes for dodge stratus 2001 car wont start showing pcodes


Have you tried turning the key to the ON position, then back to OFF three times? Typically this will display all of the codes on the electronic odometer.

Jan 03, 2010 | 2001 Dodge Stratus

1 Answer

How to fix the of my car no tach no speedometer no signal light dodge caravan 2002


1. Check the resistance of the Output Shaft Speed (OSS) sensor. It should be 300-500 ohms.

2. If the resistance is out of range, replace the sensor. 1. With the key in the Lock position, push in and hold the trip odometer reset button until the word Sof and a number show up in the odometer display. This is the software version number of the cluster.

2. Release the button and the cluster will display codes in the odometer and run through the calibration points with the gauges.

3. Note any codes.

4. The cluster will exit the calibration when the word End is displayed on the odometer.

Oct 21, 2009 | 2002 Dodge Caravan

1 Answer

I had my 2008 Toyota Avalon in for a regular oil change . The technician forgot to clear the maintenace requied light on the dash .


Set your odometer display to Trip A. Turn the ignition off. Hold the odometer stalk in and turn the car to on.(not start). The odometer display will show -------------, keep holding the stalk in until they the all go away and you see 000000. The Maint light is now reset.

May 18, 2009 | 2007 Toyota Avalon

1 Answer

Car isn't starting


I was have this problem. Battery is low. Charge battery or use cable to start. You can check the problem using Diagnostic Trouble Code. Cycle ignition key On - Off - On - Off - On within 5 sec. The odometer will show teh P-code for the DCT code number. Error code for low battery is P0562. Only "DONE" displayed on odometer inicates that no DTCs are present (no error) and the procedure is completed. PCM memory has been cleared within the last 50 ignition cycles. Hello from Croatia.

Apr 29, 2009 | 1999 Chrysler 300M

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...