Question about 1986 Oldsmobile Regency

1 Answer

Quits while running won't start, wait a while then starts. have swapped ingnition module, computer and flywheel sensor

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 56 Answers

If you can check to see if you are getting fuel when it wont start,maybe fuel pump is loosing pressure

Posted on May 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Truck won't turn over ? battery new /good connections/ starter and solenoid tested and passed/


If the truck his fuel injector with ignition modules, check the ignition pick-up sensor located in the lower side (or else) of the engine block. tt sends signal to truck computer in order to start the engine.

Nov 13, 2012 | 2000 Dodge Ram 1500 Truck

1 Answer

2006 ford ranger 6 cyl. truck starts, runs, get to destination, try to start truck back up and won't start. wait for some time (appx 20 min) and the truck will start again. I picked up a new ba


Hello
The engine and automatic transmission in this vehicles drive train are fully electronically controlled by a computer called the PCM and TCM (Power Train Control Module, Transmission Control Module). When a problem like this or other drive-ability related problems occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPENDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM

Sep 03, 2012 | 2006 Ford Ranger

2 Answers

I have a 1988 olds cutlass ciera 3.8......my problem is the car won't start......cranks over just fine but ain't fire...it has spark, fuel pressure, and the timimg is good and the wiring seems to...


Hello
The engine and transmission in this cars drivetrain are fully electronically controlled by a computer called the PCM (Power Train Control Module). Whenever a problem like this occurs the computer stores a record of the problem in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s)

Jul 04, 2012 | Cars & Trucks

1 Answer

98 Pontiac Grand Prix GT 3.8 won't after engine warms up


crank pos. sensor or maf sensor ck. the fuel press reg. also

Jun 06, 2012 | 1998 Pontiac Grand Prix

1 Answer

1997 sunfire won`t start


are you getting continuous spark? bad electronic module? check spark first. should be continuous. do you have oil pressure...some vehicles won't run if oil pressure is not there.

Jul 12, 2009 | 1997 Pontiac Sunfire

1 Answer

Will not start


sounds like a crank sensor to me i would try that

May 20, 2009 | 1996 Pontiac Grand Am

5 Answers

Motor swap now it will not start


Unfortunately, there is no easy solution here. I had the same problem with my race car. I swapped a 96 2.2 into my 97 racecar and ended up having to also swap the engine wiring harness, computer, instrament cluster and pass module. The engine harness will bolt to the interior harness even though the wire colors are not the same. Just make sure you match the large yellow wire on the 96 harness to the large purple wire on the 97 harness. It sounds pretty complicated but it only took me maybe an hour to perform the swap. Now I'm back up and running and will be racing again this weekend.

Jun 24, 2008 | 1997 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...