Question about 1998 Nissan Sentra

1 Answer

Why my Nissan 1998 Sentra Generator burn out every 4 mounth i have change at lease 3 generator this year

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 77 Answers

Bad voltage regulator or weak battery.
They have alternators not generators

Posted on May 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 nissan burns out starter every 2-3 years


if u start car alot--or hav a low batt--or dont keep vehicle tuned up-----nevr run starter more 20 sec at a time-----giv it a couple min rest

May 23, 2012 | 1997 Nissan Sentra

1 Answer

Weak when it starts...


Have the battery tested it sounds like you may have a dead cell.

Feb 21, 2012 | 1998 Nissan Sentra

1 Answer

1998 ford escort altinator two bolt or three bolt? engine light is on brand new battery and the battery light is on . car just died when driving waited 7mins and it started .is it the altinator


check with volt meter. 12 volts with engine off. Should be 14 volts with engine running if alternator is working.
First, clean battery posts and cable ends. Then check owner manual for fuse locations and blown fuses. There is a large 100 amp fuse in box under hood.

Is the battery lamp lit on the dash?

Looks like 3 bolts. please rate when done

SECTION 414-02: Generator and Regulator 1998 Escort/Tracer Workshop Manual
REMOVAL AND INSTALLATION Generator -Sedan and Wagon Removal
  1. Disconnect the battery ground cable.
  1. Remove the generator drive belt.
    1. Release the tension on the drive belt.
    1. Remove the drive belt from the generator pulley.
  1. Disconnect the HO2 sensor harness clip from the generator bracket.

  1. Position the generator bracket aside.
    1. Remove the A/C line bracket bolt.
    1. Remove the power steering pressure line bracket bolts.
    1. Remove the generator bracket bolts.
    1. Position the generator bracket aside.
  1. Remove the generator bolts and position the generator aside.
  1. Remove the generator.
    1. Disconnect the two generator electrical connectors.
    1. Remove the battery positive nut and washer.
    1. Disconnect the battery positive cable and remove the generator.
step 4
snorkelbobby_37.gif

Feb 12, 2011 | 1998 Ford Escort

1 Answer

How to remove alternater 2005 mercury mariner 3.0 v-6


Removal and Installation

  1. CAUTION: Do not allow any metal object to come in contact with the generator housing and internal diode cooling fins. A short circuit may result and burn out the diodes. Disconnect the battery.
  2. Remove the RH intermediate axle shaft.
  3. Remove the 6 lower splash shield bolts and the 2 pin-type retainers.
    • To install, tighten to 8 Nm (71 lb-in) .
  1. NOTE: The LH lower splash shield must be removed before the RH lower splash shield. Remove the lower splash shields.
118886165


  1. Remove the nut and position the bracket and wiring harness aside.
  2. Rotate the front end accessory drive tensioner counterclockwise and position the accessory drive belt aside.
  3. Position the generator B+ protective cover aside and remove the generator B+ terminal nut.
    • To install, tighten to 8 Nm (71 lb-in) .
  1. Disconnect the generator electrical connector.
  2. Remove the generator upper air duct bolt.
    • To install, tighten to 4 Nm (35 lb-in) .
  1. Loosen the 2 lower generator bolts and remove the generator upper air duct.
  2. Remove the pin-type retainer from the generator shield.
  3. Remove the bolt and the generator shield.
    • To install, tighten to 4 Nm (35 lb-in)
  1. Remove the generator stud nut.
    • To install, tighten to 47 Nm (35 lb-ft) .
  1. Remove the generator stud.
    • To install, tighten to 7 Nm (62 lb-in) .
  1. Remove the 2 generator bolts.
    • To install, tighten to 47 Nm (35 lb-ft) .
  1. Position the generator aside and remove the 3 generator lower air duct nuts.
    • To install, tighten to 4 Nm (35 lb-in) .
  1. Remove the generator lower air duct.
  2. Rotate the generator to gain enough clearance and remove it through the opening in the fender well.
  3. If necessary, remove the 2 generator bracket bolts and the generator bracket.
    • To install, tighten to 47 Nm (35 lb-ft) .
  1. To install, reverse the removal procedure.

Jul 19, 2010 | 2005 Mercury Mariner

1 Answer

Change the alternator


2005 Pontiac Vibe FWD L4-1.8L VIN 8

Alternator: Service and Repair
Generator Replacement
GENERATOR REPLACEMENT
REMOVAL PROCEDURE
CAUTION:
- Refer to Battery Disconnect Caution in Service Precautions.
- Failure to observe step 1 may result in a serious personal injury. If a tool is shorted at the generator lead, the tool will become hot
enough to cause a serious burn.
1. Disconnect the negative (-) battery cable.
2. Loosen the belt tension by turning the drive belt tensioner clockwise.
3. Remove the drive belt.
4. Disconnect the wire clamp (3) from the wire clip.
5. Remove the terminal cap and nut (1).
6. Disconnect the engine wire.
7. Disconnect the generator connector (2).
8. Remove the two mounting bolts.
9. Remove the generator (4).
INSTALLATION PROCEDURE
1. Install the generator (4) to the vehicle.
NOTE: Refer to Fastener Notice in Service Precautions.
2. Secure the generator with the two generator mounting bolts.
Tighten
- Tighten the upper bolt to 25 N.m (18 lb ft).
- Tighten the lower bolt to 54 N.m (40 lb ft).
3. Connect the generator connector (2).
4. Connect engine wire to the generator.
5. Secure the engine wire with the nut.
Tighten
Tighten the nut to 9.8 N.m (86 lb in).
6. Install the terminal cap (1) to the nut.
7. Install the wire clamp (3) to the wire clip.
8. Install the drive belt.
- Visually inspect the drive belt for wear and damage.
- Minor cracks on the ribbed side of the belt are considered acceptable. Replace the belt if pieces are missing from the ribs.
- Ensure that the belt tensioner moves downward when the belt is pressed down in the center with a force of approximately 98 N (22 lb).
9. Connect the negative (-) battery cable.
Tighten
Tighten the bolt to 15 N.m (11 lb ft).

Sep 06, 2009 | 2005 Pontiac Vibe

2 Answers

How to change alternator on 2005 Jeep Wrangler Unlimited?


Straight out of the repair manual:

REMOVAL
WARNING: DISCONNECT NEGATIVE CABLE FROM BATTERY BEFORE REMOVING BATTERY OUTPUT WIRE (B+ WIRE) FROM GENERATOR. FAILURE TO DO SO CAN RESULT IN INJURY OR DAMAGE TO
ELECTRICAL SYSTEM.
(1) Disconnect negative battery cable at battery.
(2) Remove generator drive belt. Refer to 7, Cooling System for procedure.
(3) Remove generator pivot and mounting bolts/nut (Fig. 2) , or (Fig. 3). Position generator for access to wire connectors.
(4) If equipped, unsnap plastic cover from B+ terminal.
(5) Remove B+ cable output terminal mounting
nut at rear of generator (Fig. 4), (Fig. 5), or (Fig. 6). Disconnect terminal from generator.
(6) Disconnect field wire connector at rear of generator by pushing on connector tab.
(7) Remove generator from vehicle.
INSTALLATION
(1) Position generator to engine and snap field
wire connector into rear of generator.
(2) Install B+ terminal to generator mounting
stud. Tighten mounting nut. Refer to Torque Specifications.
(3) If equipped, snap plastic cover to B+ terminal.
(4) Install generator mounting fasteners and
tighten. Refer to Torque Specifications.
CAUTION: Never force a belt over a pulley rim using a screwdriver. The synthetic fiber of the belt can be damaged.

Jul 05, 2009 | 2005 Jeep Wrangler

2 Answers

NEED TO REPLACE ALTERNATOR MYSELF ON MY NISSAN QUEST 1994 WHAT ARE THE STEPS


here's 96. should be the same. Be very careful not to overtighten any of the belts or you can break the snout off the crankshaft and ruin you engine.

Section 14-02: Generator, Integral Regulator — Internal Fan and Regulator Type 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Generator Removal
  1. Disconnect the battery ground cable (14301).
  1. Raise and support the vehicle.
  1. Remove the five engine and transmission splash shield bolts and two engine and transmission splash shield screws.




  1. Remove the RH engine and transmission splash shield (6775).
  1. Remove the wire harness bracket bolt.




  1. Remove the B-terminal insulator boot.
  1. Disconnect the generator electrical connector from the generator (GEN) (10346).
  1. Remove the ground wire nut from the generator and position the ground wire aside.
  1. Remove the B-terminal nut from the generator and position the B-terminal wire aside.




  1. Loosen the inner and outer generator-to-bracket bolts.


    61f4d2f.gif

  1. Loosen the generator locking bolt.



    93c9f65.gif
  1. Loosen the generator adjustment bolt.


    6e949fa.gif

  1. Remove the drive belt (8620) from the generator pulley (10344).
  1. Remove the generator locking bolt and washer.
  1. Remove the inner generator-to-bracket bolt and the two washers.
  1. Remove the outer generator-to-bracket bolt and the two washers.
  1. Remove the generator.
Installation
To install, reverse the removal procedure. Tighten the inner generator-to-bracket bolt to 23-26 Nm (17-19 lb-ft). Tighten the outer generator-to-bracket bolt to 23-26 Nm (17-19 lb-ft). Tighten the generator locking bolt to 16-20 Nm (12-15 lb-ft). Adjust the drive belt very carefully. Refer to Section 03-05 for the procedure.

Jun 05, 2009 | 1994 Nissan Quest

Not finding what you are looking for?
1998 Nissan Sentra Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...