Question about 2005 Chrysler 300

1 Answer

Rubber fuel hose off the filler line what size is it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 24 Answers

All rubber fuel line are the same size. if you need to replace it, measure the length and ask the counter person at the auto parts place for fuel line and give them the length. they should give you the right size.

Posted on May 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to drain a 2003 Lincoln navigator fuel tank


to start with you have to remove the filler neck at the tank opening you open the doorthere will be three small Torx head screws surrounding the perimeter of the opening for the fuel tank filler remove those 3 screws allowing a filler neck to wobble inside the fender then climb under the vehicle find the location of the filler tube connection from the hose to the tank just follow that hose down we're at clamps on 516 socket nice short extension and remove that hose clamp and remove the rubber line from the fuel tank once that's complete take a piece of smaller than 38 fuel line about 3 to 4 feet long preferrably and thread it through the filler neck being aware of the tank flap on the inside do not damage any obstruction of the tank assembly when trying to fish the host through then create a siphon into your collection cans until the tank is empty enough to achieve your goal pretty straightforward and common sense will help out more than my instruction

Apr 11, 2015 | 2003 Lincoln Navigator

1 Answer

Ford fusion europe


To replace it you need to drain the fuel or drive the car until your vehicle is almost out of fuel (reserve light on )check if there is easy access to your rubber hose that goes from fuel door to your gas thank. If you can see the clamp on the hose close to the fuel thank you need to open fuel filler door, remove fuel filler cap there will be 3 or 4 screws 1/4"" size. Remove it, remove clamp from hose and air hose clamp (smaller one going to gas thank) and remove whole assembly. Installation is in reverse order of removal. Best way is to drive your car up the ramps, set the parking brake, choke the wheels and do the repair. It will probably take 1 to 2 hours of your time...

Apr 11, 2014 | 2006 Ford Fusion

1 Answer

2008 chevy 1500 crew cab 4wd z-71 5.3 v-8 when putting fuel in tak it sprays back like ther is a fuel blockage


A common problem is the filler line rubber hose collapsing if it is installed incorrectly. Look behind the quarter panel and verify it is not twisted or kinked. If that seems to be ok, pull the vent hose (that is the smaller hose that runs with the filler line) and verify that it isn't plugged. This can be accomplished with some low pressure air from a compressor. When you put air to the line, you should hear it going into the tank. It would help if you were able to see the top of the tank.

Oct 20, 2010 | Chevrolet 1500 Cars & Trucks

2 Answers

I have a 1991 Toyota Corolla and I don't know what is wrong with my fuel hose, it leaks when I make a right, and when I fill the tank to a point. And I can't locate the problem, all there is, is a stench...


you need to get your car to a car shop so they can put it on a lift to see what is wrong. fuel leak can be very dangerous.
there is a fuel pump gasket on the top of the tank
there is a filler hose goes to the side of the tank
there are a pressure hose and a return hose go to the top of the tank
there are evaporation hoses on top of the tank as well.
rubber hoses are getting old and crack easily
so there are many possibiltities that can cause leak

Mar 10, 2010 | 1991 Toyota Corolla

1 Answer

Trying to figure out how to remove the fuel tank from a 2003 Pontiac Sunfire... Have the straps, fuel line, and wires disconnected... it's still hanging there. Help.


YOU NEED TO DISCONNECT THE EXHAUST RUBBER HANGERS AND ALLOW THE REAR OF THE EXHAUST SYSTEM REST ON THE REAR AXLE.REMOVE THE FUEL TANK HEAT SHIELD.REMOVE FUEL TANK FILLER HOSE AT THE TANK.LOOSEN HOSE CLAMPS.SPRAY A LITTLE WD40 WHERE FILLER HOSE GO TO FUEL TANK.THIS WILL MAKE IT EASY TO GET HOSE OFF.USE LARGE CHANNEL LOCK PLIERS CAREFULLY.WORK HOSE OFF FUEL TANK.BECAREFUL DONT MAKE NO SPARKS.WORKING WITH FUEL TANKS IS LIKE WORKING WITH A TIME BOMB.BECAREFUL GOODLUCK.

Oct 18, 2009 | 2003 Pontiac Sunfire

2 Answers

How do I remove the fuel tank from my x300? I have undone the two straps, wireing, and disconnected the fuel pipe but the tank is still quite rigid and does not want to move, can you help.


After removing all connections and wiring from the tank and the sending unit and depressurize fuel system and drain the fuel tank and most importantly TO DISCONNECT THE BATTERY this is what you have to do :
1- Make sure to mark the wires for the sending unit so that you do not have a problem connecting in the correct place. 2- Remove bolts securing spare wheel mounting bracket and remove bracket. 3- Remove tank upper insulation pad. 4- Disconnect fuel pump harness from evaporative loss flange connection 5- Release harness attached to tank retaining straps and reposition harness downward. 6- Disconnect vapor pipe assembly from underbody pipe. 7- Push back collars on quickfit connectors and remove vapor pipe and over-pressure pipe from evaporative loss flange port. 8- Remove bolts securing tank retaining straps. 9- reposition straps upwards for access. 10- Remove strap holding filler housing solenoid block connector to harness and disconnect connector. 11- Disconnect drain tube from aperture seal (small pipe beside big one) 12- Open filler cap and remove filler neck garter spring. 13- Remove filler housing bolts. 14- Displace filler housing from body opening 15- Remove fuel tank. 16- Remove hose from evaporative loss flange and filler neck , ( Bend weld tag upwards to release hose). 17- Remove evaporative loss flange lock ring. 18- Lift flange from tank enough to disconnect fuel pump harness. 19- Remove flange and seal. 20- Inside tank , loosen hose clamps and remove fuel hoses from fuel pump module. 21- Remove fuel pump module and mounting rubber , note position of mounting rubber lugs. 22- Loosen hose clamps and remove two fuel hoses inside tank. 23- Remove tank sending unit. 24- Remove magnetic drain plug and make sure that you clean it well.
That is it your tank is out , and make sure that you mark every thing that you disconnected to install back in its proper place.
If you need any more help please let me know

Jul 12, 2009 | 1992 Jaguar XJ6

3 Answers

Diesal gas in the tank


You must drain all the diesel fuel out of the tank and purge the fuel lines as well or it will not start.

Apr 23, 2009 | 1998 Oldsmobile Cutlass

1 Answer

93 toyota pickup fuel filler hose


U can do this with special fuel injection flex hose and steel fuel line, this is not regular fuel hose, it is much thicker and much more expensive, use as much steel line as you can, flare the end of the steel line where the rubber line will be attached..

Mar 31, 2009 | 1993 Toyota Pickup

1 Answer

Can you tell me how to change fuel pump on a 1990 chevy lumina


http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152801dbaf3

when you drop the tank by following these directions you will have access to the pump

1989-94 Vehicles
See Figures 1 and 2
  1. Disconnect the negative battery cable.
  2. Properly relieve the fuel system pressure, as outlined earlier in this section.
  3. Raise and safely support the vehicle.
CAUTION Observe all applicable safety precautions when working around gasoline. Do not allow fuel spray or fuel vapors to come in contact with a spark or open flame. Keep a dry chemical (Class B) fire extinguisher near the work area. Never drain or store fuel in an open container due to the possibility of fire or explosion.
  1. Use a suitable hand operated pump device to drain the fuel through the filler tube into an approved container.
Before disconnecting any fuel lines from the fuel tank, thoroughly clean around all hose connections.
  1. Disconnect the fuel filler vent hose from the fuel tank.
  2. Detach the fuel filler hose from the fuel filler inlet tube on the fuel tank. Position the hose out of the way.
  3. Disconnect the vapor hose from the front of the fuel tank.
  4. Detach the fuel return pipe and position the hose out of the way.
  5. Disconnect the two rear rubber exhaust hangers from the rear of the exhaust system and allow the exhaust system to hang down slightly.
  6. Unfasten the exhaust shield mounting bolts, then remove the exhaust shield.
  7. Support the fuel tank with a suitable jack.
  8. Remove the two bolts securing the fuel tank straps, then swing the straps out of the way.
  9. Lower the fuel tank enough to disconnect the vapor hose from the fuel sender assembly and the vapor hose from the vapor pipe at the rear of the fuel tank.
  10. Detach the electrical connector from the fuel sender assembly and remove the two retaining clips.
  11. Remove the tank from the vehicle, slowly to ensure all connections and hoses have been disconnected.
To install:
  1. Clean all parts well. Inspect the tank for dents, rust or other damage. On high-mileage vehicles, it may be good practice to remove the fuel pump module and replace the flexible strainer on the fuel pump.
  2. Position the fuel tank under the vehicle and raise the tank with a suitable jack.
  3. Connect the vapor hose to the fuel tank at the vapor pipe at the rear of the tank and connect the vapor hose to the sender assembly.
  4. Attach the electrical connector to the fuel sender assembly.
  5. Connect the fuel feed and return lines to the sender assembly.
  6. Raise the tank into position into the vehicle and swing the mounting straps under the tank.
  7. Install the front fuel tank strap mounting bolts and tighten to 35 ft. lbs. (47 Nm).
  8. Remove the jack.
  9. Connect the fuel return pipe to the fuel feed pipe.
  10. Attach the rear fuel feed pipe to the inlet side of the fuel filter.
  11. Tighten the line fittings to 16 ft. lbs. (22 Nm). Make sure to use a back-up wrench to prevent the fuel filter from turning.
  12. Connect the vapor hose to the vapor pipe at the front of the vehicle.
  13. Attach the fuel filler vent hose to the tank. Connect the fuel filler hose to the fuel filler neck of the tank.
  14. Install the exhaust heat shield and the mounting bolts.
  15. Position the exhaust system and install the rubber hangers.
  16. Carefully lower the vehicle, then refill the fuel system
  17. Connect the negative battery cable, then install the fuel filler cap, if not done already.
  18. Turn the ignition switchONfor 2 seconds, OFF for 10 seconds, thenONand check for fuel leaks.

Jan 14, 2009 | 1998 Mercury Sable

1 Answer

1995 maxima fuel filler tube


Are you going to get a new one, or a junkyard replacement?
You have to take off the rear left tire. Secure the car with jack stands and chucks. There is a plastic cowl on the wheel-well that covers the filler tube to prevent road damage. Take it off. The filler tube is attached to the gas tank through a rubber connector hose (tube) adapter, secured to the gas tank and to the filler tube by hose clamps. Loosen both clamps.. You should replace the rubber connector, as it has been there for many years, and rubber degrades. Loosen about three or four bolts along the filler tube that attach it to the car body. The top part, by the gas lid, comes off easily, it's just a plastic dam. You have to carefully work it off the (other end) at the rubber hose connector. Once it's out, get the hose connector off the gas tank neck.
With the new filler tube, reverse the process. Getting the hose clamp tight over the gas tank neck is hard. Make sure the clamp is seated properly before tightening.
Good luck!

Oct 30, 2008 | 1995 Nissan Maxima

Not finding what you are looking for?
2005 Chrysler 300 Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...