Question about 1996 Ford Windstar

2 Answers

Got a rod knocking, what can I do? - 1996 Ford Windstar

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,763 Answers

Ive run into this with these windstars for customers and il tell you we tryed to install bearings and oil pump and it never works your better off installing a used engine,time and money to do bearings and oil pump is just not worth it,i would take that money and try to buy another van,i dont know what shape this van is in, maybe its worth fixing, i dont know, good luck and hope this helps.

Posted on May 14, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

Over haul engine or replace it, to do just a crankshaft kit you will also need to have the piston rods mechine or it will start to knock in a short time again.Good luck and I hope this was very helpful.

Posted on May 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is the deep internal knock coming from moter on 2002 dodge durango v8


deep lower engine knock can possible be whats called rod knock --where damage to a piston rod either spun bearing ,wrist pin,crack bent causing it to slap on crank or piston cylinder

May 04, 2017 | Dodge Cars & Trucks

1 Answer

My 2004 Pontiac sunfire engine is making a knocking noise what could it be


Internal damage to the engine. Usually a knocking is a loose piston rod that connects to the crankshaft. When the rod bearing gets too worn, it causes the rod to become loose around the crankshaft, and you get that horrible knocking noise or rattle. The engine has to be rebuilt (very expensive) or a replacement engine must be found.
If the knocking is loud, and not a ticking (valves or valve lifters), then it won't be long before the engine is destroyed. Too much pressure on the loose rod-soon it may come apart and blow a hole in your block from the rod disintegrating. Not a pretty sight!

Nov 20, 2016 | Pontiac Sunfire Cars & Trucks

2 Answers

I hear a knocking sound when ever I start my engine


check oil level if low add oil ---if oil milky in color like chocolate milk possible internal damage from --blown head gasket-damaged head --the knock from engine usually means that damage to a piston rod has occurred [rod knock] and knock usually doesnt throw an engine code and usually fatal to engine will need a mechanic to diagnose how bad or what extent the noise is with engine

Aug 09, 2016 | Cars & Trucks

1 Answer

Crown victoria making knocking noise


Listen to the engine, if the noise is down low it is rod if it is up high it is valves. IF it is rod knock it will eventually throw the rod.

Feb 03, 2014 | 1993 Ford Crown Victoria

1 Answer

Making knocking sound


A KNOCKING SOUND IN THE ENGINE IS MOST LIKELY CAUSED BY ONE OF THE FOLLOWING
1. PISTON SLAP: Makes a sharp metallic noise. Idle engine and short out each cylinder plug. The noise will disappear when plug with bad piston is shorted. Noise will also disappear at acceleration. This can be caused by worn or out of round cylinder, or broken piston ring. Correct problem by re-boring cylinder and/or replacing piston.
2. VALVE NOISE: Makes clicking or rattle noise. Caused by excessive wear on valve stem or lifter, out of adjustment, or stuck valve. Correct by adjusting valve clearance, replace worn valve or lifter, regrind cam, replace valve guide and /or valve. A stuck valve can sometimes be loosened by passing oil through the carburetor while engine is running.

3. ROD BEARING KNOCK: Makes sharp metallic noise similar to a piston slap. Detection is opposite of piston slap. Rod knock is not heard at idle. Knock becomes louder as engine speed is increased. Caused by excessive rod bearing clearance. Correct by adjusting rod bearing clearance to .0015 inches by removing shims. May require re-pouring rod bearing.
4. REAR MAIN BEARING KNOCK: Makes dull knocking or thud noise. Detected at speeds between 20 and 50 MPH. Knock will normally decrease or disappear while pulling or decelerating. Noise will be detected the loudest at normal driving speed, when not pulling or decelerating. Correct by adjusting bearing clearance to .001 to .0015 inches. If knock is excessive, crank should be checked for out of roundness. May need to re-pour all main bearings to correct.
5. TIMING GEAR KNOCK: usually the most difficult to diagnose. If gear is loose or badly worn it will knock in all ranges. Run engine slightly above idle speed. Slowly open and close throttle. Knock will continue to be present, but just as engine slows down knock will become a slight rattle. Remove timing pin and reinsert into timing hole on timing gear cover. Press timing pin tightly against timing gear and accelerate slightly above idle. Knock will significantly be reduced or disappear. Correct by replacing both timing gear and crank gear as a matched set. The two gears should have a backlash clearance of .003 to .004. If more than .009 inch backlash, an oversize (.005) timing gear should be installed.
6. WRIST PIN SLAP: This can not be detected by shorting out the cylinder plugs. Rapidly accelerate and decelerate the engine speed. The engine will pass through a certain speed range when the wrist pin will rattle at about the same pitch as a valve tappet noise. This can be corrected by installing a new wrist pin bushing in the rod or new wrist pin f badly worn. Wrist pin should fit the piston and connecting rod with a tight metal to metal fit. The pin can be pushed into the piston and rod with a slight pressure of the hand. Pin to rod clearance is .0003 to .0005 inches.

Dec 06, 2013 | Nissan Cars & Trucks

1 Answer

V6 knocking noise


A KNOCKING SOUND IN THE ENGINE IS MOST LIKELY CAUSED BY ONE OF THE FOLLOWING
1. PISTON SLAP: Makes a sharp metallic noise. Idle engine and short out each cylinder plug. The noise will disappear when plug with bad piston is shorted. Noise will also disappear at acceleration. This can be caused by worn or out of round cylinder, or broken piston ring. Correct problem by re-boring cylinder and/or replacing piston.
2. VALVE NOISE: Makes clicking or rattle noise. Caused by excessive wear on valve stem or lifter, out of adjustment, or stuck valve. Correct by adjusting valve clearance, replace worn valve or lifter, regrind cam, replace valve guide and /or valve. A stuck valve can sometimes be loosened by passing oil through the carburetor while engine is running.

3. ROD BEARING KNOCK: Makes sharp metallic noise similar to a piston slap. Detection is opposite of piston slap. Rod knock is not heard at idle. Knock becomes louder as engine speed is increased. Caused by excessive rod bearing clearance. Correct by adjusting rod bearing clearance to .0015 inches by removing shims. May require re-pouring rod bearing.
4. REAR MAIN BEARING KNOCK: Makes dull knocking or thud noise. Detected at speeds between 20 and 50 MPH. Knock will normally decrease or disappear while pulling or decelerating. Noise will be detected the loudest at normal driving speed, when not pulling or decelerating. Correct by adjusting bearing clearance to .001 to .0015 inches. If knock is excessive, crank should be checked for out of roundness. May need to re-pour all main bearings to correct.
5. TIMING GEAR KNOCK: usually the most difficult to diagnose. If gear is loose or badly worn it will knock in all ranges. Run engine slightly above idle speed. Slowly open and close throttle. Knock will continue to be present, but just as engine slows down knock will become a slight rattle. Remove timing pin and reinsert into timing hole on timing gear cover. Press timing pin tightly against timing gear and accelerate slightly above idle. Knock will significantly be reduced or disappear. Correct by replacing both timing gear and crank gear as a matched set. The two gears should have a backlash clearance of .003 to .004. If more than .009 inch backlash, an oversize (.005) timing gear should be installed.
6. WRIST PIN SLAP: This can not be detected by shorting out the cylinder plugs. Rapidly accelerate and decelerate the engine speed. The engine will pass through a certain speed range when the wrist pin will rattle at about the same pitch as a valve tappet noise. This can be corrected by installing a new wrist pin bushing in the rod or new wrist pin f badly worn. Wrist pin should fit the piston and connecting rod with a tight metal to metal fit. The pin can be pushed into the piston and rod with a slight pressure of the hand. Pin to rod clearance is .0003 to .0005 inches.

Dec 06, 2013 | Cars & Trucks

1 Answer

Maxima got a knocking noise by the power steering pump just replace the rod bearings and still knocks down by the power steering pum


You replaced the rod bearings, were they knocking?
Also, you have wrist pins that connect the piston to the rod, if one is bad it will knock and sound like a bearing.

Nov 25, 2013 | 2002 Nissan Maxima

1 Answer

Rod knock during warm up


either you have a bent rod or your rod is just heating up and the metal is popping as it expands from the heat!

Oct 12, 2012 | 2002 GMC Sierra 1500

1 Answer

1999 3.5L OLDS INTRIGUE,HAS ROD KNOCK,COLUD IT BE A BAD SENSOR OR A BAD HARMACA BALANCER?


any codes would show if sensor bad or going bad a rod knock is internal lower engine problem(connecting rod) rod knock can b bearing -rod-pin -piston harmonic balancer is on crankshaft out side of block if bad usually breaks off or causes heavy vibration

Nov 04, 2009 | 1999 Oldsmobile Intrigue

1 Answer

Knocking in the engine


2 things that this SUV are known foe Rod knocks and bad tranny.. both very $$$$$ but they are great when they are working right.... Rod knocks are very VERY bad

Jan 19, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
1996 Ford Windstar Logo

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...