Question about 1984 Plymouth Reliant

1 Answer

Need a rad fan motor, shroud #4266565 can not locate this item?

I have looked at auto parts stores in town put they do not ref: shroud #4266565

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,088 Answers

Check you local wrecking yard. If they have or can get one, it is usually half priced. Good luck!

Posted on May 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I take off engine fan blades 96 Lincoln towncar 4.6liter v8


  1. d/c neg batt cable
  2. remove fan shroud top section or you may have to remove whole thing
  3. block fan blades so they can not turn.say a piece of wood
  4. remove bolts from front of fan 4 or 6 bolts
  5. remove fan blades
Hope this helps mike

Feb 08, 2016 | Lincoln Cars & Trucks

1 Answer

I need a belt diagram for a 2012 chevy Impala and haven't had any luck online and the auto parts stores say they don't have one in their system yet. Please help!!


Typically Chevy puts the diagram right on the fan shroud, look on the top of the shroud, will be embossed diagram.

Jun 18, 2015 | 2012 Chevrolet Impala

1 Answer

A/c blower only works on the highest setting


There is a "blower motor resistor" that controls the lower speeds of the fan. Check with your local parts store, Auto Zone / Action Auto / Napa, and they will be able to direct you to the location of the resistor.
The resistors cost is between 10 and 20 dollars depending if you have auto a/c or manual.
Good luck.

Jun 21, 2010 | 2002 Chrysler Town & Country

1 Answer

Describe your how do i replace 1993 jeep Cherokee radiator


Start steps when vehicle is cold. Drain the rad fluid - located passenger side lower bottom of the rad. When draining remove the rad cap (keep your bucket there for complete job). After empty, the tranny lines must be removed, a tool is available for this - from Parts Source or UAP. They join at the bottom of the rad, after removing (don't break the clips or lose them) keep the lines upright to avoid draining the tranny fluid. Undo the 2 bolts holding the fan shroud, slowly and gently push the shroud towards the motor (do not bend the tranny lines attached to the rad). Then lift up and move to the motor. Undo the clamps holding both rad hoses, drain the bottom hose into the bucket. Undo the 8 screws or bolts (10mm ??) holding the top plate that keeps the rad stationary - the hood latch is connected to it, move it towards the front of the vehicle. Pretend you are dismantling a bomb, one wrong move and you will be replacing more than a rad. Lift the rad straight up, watching everything in the way. With the rad on the ground with the tranny lines pointing upright, spray WD40 on the tranny lines and undo them (inspect for any holes). Be smooth when you do it or you will be buying new ones. Start with last step first when you install new rad.

May 10, 2010 | 1993 Jeep Grand Cherokee

1 Answer

How to remove a water pump


Locate water pump.. It's where the bottom radiator hose goes from the radiator. Remove any brackets or parts that are in your way. Remove water pump! Reverse procedure for installation. You have to remove the fan clutch from the water pump shaft and lift the shroud, fan and clutch all out together. remove two bolts in the center radiator support which let the radiator move forward an inch or so, loosen the fan from the clutch for a little more wiggle room to get it out. The shroud will have rubber splash shields hooked to the lower sides too, so be sure to unhook them or you will tear out the holes in the rubber shields.The fan clutch has to come off anyway because it's attached to the water pump. You don't need to remove the fan shroud. Just take out two bolts on the fan clutch and loosen the other two so you can push the clutch back a little (DON'T let the fan clutch fall). Then remove the water pump. It's a little tight, but much easier than removing the fan shroud.the only specialty tool that you will need is the water pumpt "grab" tool and the fan clutch wrench. These two items come together in one kit that you can rent from the Auto Parts store.
The "grab" tool holds the water pumpt pully firmly while you rotate the fan clutch retainer using the fan clutch wrench.

DO NOT attempt to use a break over bar or some other home-grown tool to hold the water pump pully while attempting to break the fan clutch free - you will mess up the heads of the four retainer bolts holding the pully to the water pump face.
this will help.thanks.

Feb 21, 2010 | 2006 GMC Envoy

1 Answer

How to take out my 1993 jeep cherokee grand laredo 4.o radiator. in line six cid


Start steps when vehicle is cold. Drain the rad fluid - located passenger side lower bottom of the rad. When draining remove the rad cap (keep your bucket there for complete job). After empty, the tranny lines must be removed, a tool is available for this - from Parts Source or UAP. They join at the bottom of the rad, after removing (don't break the clips or lose them) keep the lines upright to avoid draining the tranny fluid. Undo the 2 bolts holding the fan shroud, slowly and gently push the shroud towards the motor (do not bend the tranny lines attached to the rad). Then lift up and move to the motor. Undo the clamps holding both rad hoses, drain the bottom hose into the bucket. Undo the 8 screws or bolts (10mm ??) holding the top plate that keeps the rad stationary - the hood latch is connected to it, move it towards the front of the vehicle. Pretend you are dismantling a bomb, one wrong move and you will be replacing more than a rad. Lift the rad straight up, watching everything in the way. With the rad on the ground with the tranny lines pointing upright, spray WD40 on the tranny lines and undo them (inspect for any holes). Be smooth when you do it or you will be buying new ones. Start with last step first when you install new rad.

Feb 02, 2010 | 1993 Jeep Cherokee Country

1 Answer

How to remove a fan shroud


the fan shroud is actually a full station unit it houses coolant and winshield fluid, to remove it you must first locate all the bolts that connect the top and bottob portion the unit disassembles like a sharks mouth look down the sides the bolts will be on the sides and rad cradle(top) they are 10 mil.

Dec 12, 2009 | 1999 Dodge Dakota

1 Answer

I need to replace the radiator on a 97 jeep laredo 8 cyl. It looks as if it needs to come out from the bottom. Is this correct?


Good Day;
no the rad is straight up and out: the following is removal of the rad

--access to rad drain **** remove the rad grill
--disconnect electric cooling fan electrical connector, if equipped
--if equipped remove two electric cooling fan mounting bolts. Lift cooling fan straight up until alignment tabs at the bottom are clear of the slots in the bracket at the bottom of rad
--remove the two mechanical (non-electrical) fan shroud mounting bolts, lift shroud straight up until alignment tabs at the bottom are clear of slots in the bracket at the bottom of rad. place shroud over the mechanical fan.
--if equipped disconnect and plug automatic transmission fluid cooler lines, quick connect fitting release tool may be needed. if equipped with a remote transmission cooler, remove the line to cooler from bracket at the bottom of rad.
--disconnect rad upper and lower hoses
--mark the position of the hood latch striker on the rad cross member and remove the striker
--remove the two upper rad upper cross member isolator nuts
--remove the four rad upper cross member bolts and remove the cross member.
--if equipped with air conditioning, separate rad from condenser by removing condenser-to-rad mounting brackets.
--lift the rad straight up and out of the eng compartment.
I hope this helps

Cheers

Jul 09, 2009 | 1997 Jeep Grand Cherokee

1 Answer

Need to replace the left rad fan motor, any ideas on how to do it if i have the new part?


  1. Remove radiator from vehicle.
  2. Remove fan shroud retaining bolts, and cooling fan motor/blade/shroud assembly.
  3. Remove fan blade retaining clips and blades.
  4. Remove motor mounting screws and motors.
  5. If necessary, remove Constant Control Relay Module (CCRM).
  6. Reverse procedure to install. Torque CCRM screws to 40-56 in lb, and shroud retaining bolts to 24-48 ft lb.

May 27, 2009 | 1996 Lincoln Continental

2 Answers

I'd like to replace my radiator .What are the basic things to do and what tools are necessary


get ready .. antifrez pan new hoses clamps 10mm.12mm.14.. mm. sockets rachet drain the radiator from lower hose star the car for about 5 seconds . this way the car draints out all the ant.

Feb 25, 2009 | 1995 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...