Question about 1999 GMC Suburban

3 Answers

Where is the oxygen sensor at and is it hard 2 get to

Posted by on

  • yadayada
    yadayada May 14, 2010

    WHICH ONE THERE ARE AT LEASE THREE

×

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 14,036 Answers

YOU HAVE A O2 SENSOR ON EXHAUST MANIFOLD AND YOU HAVE OXYGEN SENSOR AFTER THE CATALYTIC CONVERTER.YOU NEED TO BUY THE OXYGEN SENSOR SOCKET TO REMOVE SENSOR.OXYGEN SENSOR IS HARD TO REMOVE FROM COLD ENGINE COULD DAMAGE THREAD HOLE REMOVING IT..YOU HAVE TO RUN ENGINE A MINUTE OR TWO TO HEAT UP EXHAUST MANIFOLD.THIS WILL MAKE MAKE JOB EASIER TO REMOVE OXYGEN SENSOR.USE SPRAY LIQUID WRENCH ON SENSOR TO HELP LOOSEN IT UP.TO GET TO THE OXYGEN SENSOR YOU HAVE TO SAFELY RAISE AND SUPPORT VECHICLE ON JACKSTANDS.BESURE TO WEAR LONG SLEEVE COVERALLS AND GLOVES TO KEEP FROM GETTING BURN.AFTER YOU TURN OFF ENGINE A MINUTE OR TWO.BEFORE REMOVING THE O2 SENSORS.

Posted on May 14, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

You have 4 o2 sensor's
two right after the exhaust magifold
and
two after the catalytic converter

Not bad to get to, you will need a 7/8 wrench or
a o2 sensor socket 1/2" drive.
Good luck
Hope this was very helpful.

Posted on May 14, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 50 Answers

Most of these vehicles have 3, one on each exhaust pipe, left and right, and a third "downstream" just before the cat. converter. They screw into a "bung" (threaded nut) welded to the pipe. They kind of look like a spark plug with a wire, or 2, coming off of it that plugs into a harness near by. If you had the check engine light on the code usually tells you which one it is.

Posted on May 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is P0157 code for 2006 saturn Vue


Bank 2 sensor 2 fault. That would be the downstream oxygen sensor for bank 2.

Aug 03, 2015 | Saturn Cars & Trucks

Tip

Which Oxygen Sensor Is It?


There are many inquiries online about which oxygen sensor to change. Oxygen sensor failure codes are very common on a lot of vehicles. With all of today's vehicles having at least two oxygen sensors and many having three or four of them, it can be a little confusing as to which one is causing the problem.

Before we get into which sensor is which, we need to have a little discussion about oxygen sensor fault codes. There are several different types of oxygen sensor fault codes. Here are just some of the most common ones:

P0135 "Oxygen Sensor Heater Circuit Bank1 Sensor 1"
P0141 "Oxygen Sensor Heater Circuit Bank 1 Sensor 2"
P0147 "Oxygen Sensor Circuit Bank 1 Sensor 3"
P0152 "Oxygen Sensor Voltage High Bank 2 Sensor 1"
P0159 "Oxygen Sensor Slow Response Bank 2 Sensor 2"
P0171 "Oxygen Sensor Lean Sensor 1 Bank 1"
P0172 "Oxygen Sensor Lean Sensor 1 Bank 2"
P0174 "Oxygen Sensor Rich Sensor 1 Bank 1"
P0175 "Oxygen Sensor Rich Sensor 1 Bank 2"

There are many more possible oxygen sensor codes, but I only listed these to make my point. Many times the oxygen sensor code is NOT caused by the oxygen sensor itself. "Lean" or "Rich" oxygen sensor codes (i.e. P0171, P0174) are usually caused by something other than the oxygen sensor. Something is wrong, causing the engine to run lean (not enough fuel or too much air) or causing the engine to run rich (too much fuel or not enough air). In these cases, replacing the oxygen sensor will not fix a thing. (That is, unless you are trying to fix your bank account from having too high of a balance!) The new oxygen sensor will just set the same code as the original one. This is because the oxygen sensor is not CAUSING the problem, it is only REPORTING the problem.

High voltage codes (like P0152 above) can be caused by the oxygen sensor wires being shorted to another wire inside the wiring harness. Sometimes these codes are caused by bad grounds where some other component is trying to ground through the oxygen sensor circuit. Again, replacing the oxygen sensor will not fix this! In short, the problem needs to be diagnosed before running out and buying an oxygen sensor.

Just because a fault code has "Oxygen Sensor" or "O2 Sensor" or "O2S" in its description does not necessarily mean that an oxygen sensor needs to be replaced. Many do-it-yourselfers believe that all there is to fixing the car is to hook it to the "magic box", collect the fault codes and replace the parts the computer tells you to replace. There is nothing further from the truth.

Fault codes only point you toward which SYSTEM is failing. The system must be diagnosed to find the CAUSE of the failure. If this is not done properly, it will only result in wasting a bunch of your money. This is what you were trying to avoid by doing it yourself!

So, after reading all of the above, if you think you still want to replace an oxygen sensor, but don't know which one; here is how to figure it out:

Oxygen sensors are always numbered like this:

Bank 1 Sensor 1
Bank 2 Sensor 1
Bank 1 Sensor 2
Bank 2 Sensor 2

Some manufacturers use a kind of shorthand that reads different, but means the same thing:

Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder #1 is located and, of course, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only one bank and it is always referred to as Bank 1. The exception to the 4 cylinder rule is on certain 4 cylinder engines (specifically, some Toyotas) there are two catalytic converters used. In this case, Bank 1 sensors will still be in the pipe for the catalyst that is connected to cylinder #1 and Bank 2 sensors will be in the other one.

Sensor 1 is always the "upstream" sensor (the one located BEFORE the catalytic converter).
Sensor 2 is always the "downstream" sensor (the one that is located AFTER the catalytic converter).
Sensor 3 refers to the ONLY "downstream" sensor where there are two sensors before the catalyst and only one after the catalyst. On very few vehicles the reference to this reads "Bank 1 Sensor 3".

If you do not know where cylinder #1 is, then you need to get a diagram of the firing order for your engine. Just post a question on FixYa.com and make sure you give the YEAR, MAKE, MODEL, and ENGINE SIZE of your vehicle and one or more of our experts will be happy to tell you how to find cylinder #1.

- DTTECH
ASE Certified Master Automobile Technician


Also check out this article by dttech: What Else Could Be Wrong?

on Apr 29, 2011 | Ford F-150 Cars & Trucks

1 Answer

Code p0036


Possible causes
- Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 fuse
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 harness is open or shorted
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit poor electrical connection
- Faulty Engine Control Module (ECM)


Read more: http://engine-codes.com/p0036.html#ixzz2ib20bfW1

Oct 23, 2013 | Cars & Trucks

1 Answer

2002 toyota avalon engine check light on P0078 and P007C


P0050 HO2S Heated Oxygen Sensor -Control Circuit (Bank 2 Sensor 1)

P0051 HO2S Heated Oxygen Sensor -Control Circuit Low (Bank 2 Sensor 1)

P0052 HO2S Heated Oxygen Sensor -Control Circuit High (Bank 2 Sensor 1)

P0053 HO2S Heated Oxygen Sensor -Resistance (Bank 1 Sensor 1)

P0054 HO2S Heated Oxygen Sensor -Resistance (Bank 1 Sensor 2)

P0055 HO2S Heated Oxygen Sensor -Resistance (Bank 1 Sensor 3)

P0056 HO2S Heated Oxygen Sensor -Control Circuit (Bank 2 Sensor 2)

P0057 HO2S Heated Oxygen Sensor -Control Circuit Low (Bank 2 Sensor 2)

P0058 HO2S Heated Oxygen Sensor -Control Circuit High (Bank 2 Sensor 2)

P0059 HO2S Heated Oxygen Sensor -Resistance (Bank 2 Sensor 1)

P0060 HO2S Heated Oxygen Sensor -Resistance (Bank 2 Sensor 2)

P0061 HO2S Heated Oxygen Sensor -Resistance (Bank 2 Sensor 3)

P0062 HO2S Heated Oxygen Sensor -Control Circuit (Bank 2 Sensor 3)

P0063 HO2S Heated Oxygen Sensor -Control Circuit Low (Bank 2 Sensor 3)

P0064 HO2S Heated Oxygen Sensor -Control Circuit High (Bank 2 Sensor 3)

P0065 Air Assisted Injector -Range/Performance

P0066 Air Assisted Injector -Circuit Malfunction or Circuit Low

P0067 Air Assisted Injector -Circuit High

P0068 (MAP) Manifold Absolute Pressure /(MAF) Mass Air Flow - Throttle Position

Correlation

P0069 (MAP) Manifold Absolute Pressure / (BARO)Barometric Pressure Correlation

P0070 Ambient/Outside Air Temperature Sensor -Circuit Malfunction

P0071 Ambient/Outside Air Temperature Sensor -Range/Performance Problem

P0072 Ambient/Outside Air Temperature Sensor -Circuit Low Input

P0073 Ambient/Outside Air Temperature Sensor -Circuit High Input

P0074 Ambient/Outside Air Temperature Sensor -Circuit Intermittent

P0075 Intake Valve Control Solenoid Circuit Malfunction (Bank 1)

P0076 Intake Valve Control Solenoid Circuit Low (Bank 1)

P0077 Intake Valve Control Solenoid Circuit High (Bank 1)

P0078 Exhaust Valve Control Solenoid Circuit Malfunction (Bank 1)

P0079 Exhaust Valve Control Solenoid Circuit Low (Bank 1)

P0080 Exhaust Valve Control Solenoid Circuit High (Bank 1)

P0081 Intake valve Control Solenoid Circuit Malfunction (Bank 2)

P0082 Intake Valve Control Solenoid Circuit Low (Bank 2)

P0083 Intake Valve Control Solenoid Circuit High (Bank 2)
P0084 Exhaust Valve Control Solenoid Circuit Malfunction (Bank 2)

Mar 22, 2013 | 2002 Toyota Avalon

2 Answers

Where is the bank 1 sensor 1 o2 sensor located in a 2006 hyundai sontata gls v6?


The bank has to do with which side of the engine. The 'Sensor 1' indicates that it is upstream of the catalytic converter.

Heated Oxygen Sensor Removal & Installation Heated Oxygen Sensor (Front) (2.4L) hyundai-04-24-5822.gif

Heated Oxygen Sensor (Rear) (2.4L) hyundai-04-24-5823.gif

Heated Oxygen Sensor (Bank 1/Sensor 1) (3.3L) kia-04-00-5213.gif

Heated Oxygen Sensor (Bank 1/Sensor 2) (3.3L) kia-04-00-5214.gif

Heated Oxygen Sensor (Bank 2/Sensor 1) (3.3L) kia-04-00-5215.gif

Heated Oxygen Sensor (Bank 2/Sensor 2) (3.3L) hyundai-04-33-5855.gif

prev.gif next.gif

Jan 13, 2011 | 2006 Hyundai Sonata

1 Answer

Subaru wrx impreza showing fault code p0037. how do i fix this fault which sensor is it and where is the sensor located?


http://helpforcars.net/obd_codes/codes.php?code=P0037

It's an O2 sensor according to the above link, and it is bank 1 sensor 2 low, the 2 meaning that it is downstream past the catalytic converter but not on the manifold.

- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit open shorted to ground
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit poor electrical connection
- Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit fuse
- Faulty Engine Control Module (ECM) Possible Solution Tech Notes The code means that there is a problem with the heater element circuit of the heated oxygen sensor. Water getting inside the heated oxygen sensor connector can caused the heated oxygen sensor fuse to blow, which is a very common problem for this type codes. Before replacing the sensor, check for the condition of the heated oxygen sensor fuse and connectors.
Good luck on this repair.

Jan 01, 2011 | 2001 Subaru Impreza

1 Answer

Have a oxygen sencor and dont know were to put it in at thanks....


WELL WHICH OXYGEN YOU REPLACING THE UPSTREAM OXYGEN SENSOR MOUNTED IN EXHAUST MANIFOLD AND THE DOWN STREAM OXYGEN SENSOR LOCATED IN THE EXHAUST SYSTEM AFTER THE CATALYTIC CONVERTER .YOU NEED A OXYGEN SENSOR SOCKET TO REMOVE IT.TO REMOVE OXYGEN SENSOR CRANK VECHICLE TO GET OXYGEN SENSOR HOT BECAUSE HARD TO REMOVE WHEN COLD.BECAREFUL DONT GET BURN ON EXHAUST MANIFOLD WHEN REMOVING OXYGEN SENSOR.AND WHEN INSTALLING NEW OXYGEN SENSOR USE ANTI SEIZE COMPOUND ON SENSOR THREADS.BUT MOST OF THE TIME NEW SENSOR WILL HAVE ANTI SEIZE COMPOUND ON IT.

Dec 08, 2010 | 2002 Jaguar S-Type

2 Answers

How many oxygen sensors in a 2001 chrysler sebring 3.0


17c3292.jpg

Fig. Heated Oxygen (HO2S) location (sensor 1)-2.4L engine

db6f426.jpg

Fig. Heated Oxygen (HO2S) location (sensor 2)-2.4L engine

99e413c.jpg

Fig. Heated Oxygen (HO2S) location (bank 1, sensor 2) (bank 2, sensor 2)-2.7L engine

e2a250f.jpg

Fig. Heated Oxygen (HO2S) location (bank 2, sensor 1)-2.7L engine

I hope help you with this (rated this help). Good luck.

Sep 09, 2009 | 2001 Chrysler Sebring

1 Answer

My check engine light has come on in my 2006 Pontiac G6 after 2 and a half years. What could possibly be wrong since I keep my car serviced and the guys had just told me that my car was in tip top shape?


P0016 - Crankshaft Position Camshaft Position Correlation Bank 1 Sensor A
P0030 - Heated Oxygen Sensor (H02S) Heater Control Circuit Bank 1 Sensor 1
P0031 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 1 Sensor 1
P0032 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 1 Sensor 1
P0036 - Heated Oxygen Sensor (HO2S) Heater Control Circuit Bank 1 Sensor 2
P0037 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 1 Sensor 2
P0038 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 1 Sensor 2
P0050 - Heated Oxygen Sensor (HO2S) Heater Circuit Bank 2 Sensor 1
P0051 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 2 Sensor 1
P0052 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 2 Sensor 1
P0053 - HO2S Heater Resistance Bank 1 Sensor 1 (PCM)
P0054 - HO2S Heater Resistance Bank 1 Sensor 2 (PCM)
P0056 - Heated Oxygen Sensor (HO2S) Heater Circuit Bank 2 Sensor 2
P0057 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 2 Sensor 2
P0058 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 2 Sensor 2
P0068 - Throttle Body Airflow Performance (PCM)
P0100 - MAF Sensor Circuit Insufficient Activity

Jun 25, 2009 | 2006 Pontiac G6

1 Answer

Number one oxygen sensor on 2001 Oldmobile silhouette


Purchased an oxygen sensor socket from an auto parts store. Went from under the van up to the sensor and was able to take the sensor out and replaces using the socket. Wasn't hard at all took about 1/2 hour total.

Feb 08, 2009 | 1999 Oldsmobile Silhouette

Not finding what you are looking for?
1999 GMC Suburban Logo

207 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...