Question about 1994 Ford Explorer Limited

1 Answer

I have a '94 Explorer auto trans, 100000 miles. I am replacing the transmission for the 4th time. They fly wheel would turn to get the torque converter out of the old one. Will turn with no trans in, but when I put the new trans in, it refuses to turn. Any ideas? This is new for us and we can't figure it out. The new trans has been check several time to make sure it is the right one. Everything lines up.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

Make sure the torque converter is in all the way' with transmission out turn convert clockwies as you push converter in, need to be in all the way or went you bolt transmission to engine the converter will smach on fly wheel and you wont be able to turn fly wheel to bolt to converter. good luck.

Posted on May 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

When I bolt the 2.4L to the automatic transmission the fly wheel will not turn


You must make sure that your torque converter is fully seated into your front pump or you will break your pump. You should feel three clunks as you work the converter into the pump and it should sit well inside of the bell housing when it is fully seated. Your best bet is to unbolt the trans and hope you haven't already cracked the pump by tightening up the motor. Make sure the converter is all the way in, and then bolt up the engine a little at a time evenly all of the way around.

Aug 18, 2015 | 2006 Chrysler PT Cruiser

2 Answers

Why does the transmission slip from 4th back to 3rd after driving about fifty miles ?


seals going bad fluid to thin and old filter needs changed or clutch in trans worn how many miles on trans if more than 200k rebuild it and replace torque converter

Aug 21, 2014 | 1998 GMC Sonoma

1 Answer

Transmission engages but does not drive and makes a whineing noise when in park


Toyota 4 Runner has either auto transmission or manual transmission. If it is auto trans, it could be due to the following reasons:
1.Wrong grading and classification of transmission oil. (ATF Dexron II).
2. Clogged transmission filter. (Clean or replace)
3. Worn out clutch friction discs and pressure plates. (replace)
4. Broken fly wheel and/or torque converter. (replace)
5. Check transmission control knobs and switches for if they are at their actual position where they are supposed to be.

Dec 06, 2013 | 1994 Toyota 4Runner

1 Answer

04kiaoptima 2.4crankshaft torque specs


main bearings torque is 18 ft lbs. plus 90 - 94 degrees, rod bearings torque is 13 - 16 ft lbs. plus 90 - 94 degrees.crankshaft damper bolt torque 80 - 94 ft lbs, fly wheel bolts torques 94 - 101 ft lbs.

Oct 29, 2012 | 2004 Kia Optima

1 Answer

I am putting a 99 ford explorer tranny in a 98 explorer sport with the 4.0 sohc engine. the bolts match perfect and the torque converter from the 99 tranny lines up perfect with the fly wheel. when I go to...


The torque converter is not all the way in the transmission. Pull the transmission back out(unfortunately) and you will need to shake and wiggle while lightly pushing the torque converter into the transmission. Once it goes over the splines for the pump, you will know and the space between it and the transmission housing will be minimal.

May 13, 2010 | 1998 Ford Explorer

1 Answer

1984 transmission wines in all gears 5 spd trans am 305 engine. How can i get the wine to go away?


If this vehicle is an automatic ....the whinning your hearing is the bearing on the oil pump in the torque converter. Time for a new transmission.
If its a stick the noise may be the throw out bearing of the clutch. Time for a new clutch.
If it is a stick and your replacing the clutch have the pilot bearing and input shaft (of transmission) bearing replaced, and if the fly wheel doesn't have any meat on it replace it.

Apr 01, 2010 | 1984 Pontiac Firebird

2 Answers

Auto shift not working - 94 Chev Suburban?


Check the trans fluid level, if that is good then you will need to have the trans serviced.

Oct 12, 2009 | 1994 Chevrolet Suburban

1 Answer

Need clutch replacement directions for Ford Ranger


Remove drive shaft,remove crossmember under transmission.Remove transmission and diconnect linkage.Remove bell housing,and clutch berring assembely.Remove bolts on pressure plate.Once this is done.Remove fly wheel for machineing.you will need a pilot shaft to alighn clutch assemblely.Possible one will come with new clutch and pressure plate.Reverse assemblely in same order remember to torque all your bolts with torque wrench.Take your time.

Apr 19, 2009 | 1994 Ford Ranger Supercab

1 Answer

Transmission Fluid


Manual trans as well as auto trans,the fluid should be changed once a year and/or every 30k miles.

Sep 15, 2008 | 1998 Ford Explorer

Not finding what you are looking for?
1994 Ford Explorer Limited Logo

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...