Question about 2004 Ford F150

1 Answer

Spark plug installation - 2004 Ford F150

Posted by on

Ad

1 Answer

Question? You can't find them? Remove the coil covers,then the coils,to get to the plugs

Posted on May 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hesitating on a 2006 Buick Lacrosse


this is for a 3.6L engine, should be the same either way. doesnt seem extremely difficult

  1. Turn the ignition OFF.
  2. Remove the ignition coil.
  3. Use compressed air in order to remove debris from the spark plug cavity.
CAUTION: Refer to Safety Glasses and Compressed Air Caution in Service Precautions .

NOTE: Clean the spark plug recess area before removing the spark plug. Failure to do so could result in engine damage because of dirt or foreign material entering the cylinder head, or by the contamination of the cylinder head threads. The contaminated threads may prevent the proper seating of the new plug. Use a thread chaser to clean the threads of any contamination.
  1. Remove the spark plug.
NOTE: Allow the engine to cool before removing the spark plugs. Attempting to remove the spark plugs from a hot engine may cause the plug threads to seize, causing damage to cylinder head threads.

INSTALLATION PROCEDURE
  1. Ensure that the spark plug gap is equivalent to the spark plug gap specification. Refer to Ignition System Specifications.
NOTE:
  • Use only the spark plugs specified for use in the vehicle. Do not install spark plugs that are either hotter or colder than those specified for the vehicle. Installing spark plugs of another type can severely damage the engine.
  • Check the gap of all new and reconditioned spark plugs before installation. The pre-set gaps may have changed during handling. Use a round feeler gage to ensure an accurate check. Installing the spark plugs with the wrong gap can cause poor engine performance and may even damage the engine.
  1. Install the spark plug.
NOTE: Be sure that the spark plug threads smoothly into the cylinder head and the spark plug is fully seated. Use a thread chaser, if necessary, to clean threads in the cylinder head. Cross-threading or failing to fully seat the spark plug can cause overheating of the plug, exhaust blow-by, or thread damage.

Tighten the spark plug to 20 N.m (15 lb ft) .
  1. Install the ignition coil.


26252193-gjaozkvamcccpvfgr5edjxnv-1-0.gif

Aug 04, 2016 | 2006 Buick LaCrosse

1 Answer

How to change spark plugs



REMOVAL PROCEDURE
  1. Remove the ignition control modules.
  2. Clean the spark plug recess area with low pressure air.
CAUTION: Wear safety glasses when using compressed air, as flying dirt particles may cause eye injury.

NOTE: Clean the spark plug recess area before removing the spark plug. Failure to do so could result in engine damage because of dirt or foreign material entering the cylinder head, or by the contamination of the cylinder head threads. The contaminated threads may prevent the proper seating of the new plug. Use a thread chaser to clean the threads of any contamination.
117381099
  1. Remove the spark plugs from the cylinder heads.
NOTE: Allow the engine to cool before removing the spark plugs. Attempting to remove the spark plugs from a hot engine may cause the plug threads to seize, causing damage to cylinder head threads.
  1. Inspect the spark plugs. Refer to Spark Plug Inspection.
INSTALLATION PROCEDURE
  1. Measure the spark plug gap on the spark plugs to be installed. Compare the measurement to the gap specifications.
NOTE:
  • Use only the spark plugs specified for use in the vehicle. Do not install spark plugs that are either hotter or colder than those specified for the vehicle. Installing spark plugs of another type can severely damage the engine.
  • Check the gap of all new and reconditioned spark plugs before installation. The pre-set gaps may have changed during handling. Use a round feeler gage to ensure an accurate check. Installing the spark plugs with the wrong gap can cause poor engine performance and may even damage the engine.
117381099
  1. Install the spark plugs to the cylinder heads.
NOTE:
  • Be sure that the spark plug threads smoothly into the cylinder head and the spark plug is fully seated. Use a thread chaser, if necessary, to clean threads in the cylinder head. Cross-threading or failing to fully seat the spark plug can cause overheating of the plug, exhaust blow-by, or thread damage.
  • Refer to Component Fastener Tightening Notice in Service Precautions.
Tighten the spark plugs to 20 N.m (15 lb ft) .
  1. Install the ignition control modules.

Jul 14, 2014 | 2006 Cadillac SRX

1 Answer

Describe your how fix my pontiac 2000 montana Problem changing spark plugs



Inspection

Inspect for the correct routing of the spark plug wires. Improper routing may cause cross-firing. Inspect each wire for any signs of cranks or splits in the wire. Inspect each plug wire boot for tearing, piercing, arcing, carbon tracking or a corroded terminal.
If there is any corrosion, carbon tracking or arcing indicated on a plug wire boot or terminal, both the plug wire and component it was connected to should be replaced.


Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the left side spark plug wires from the spark plugs.
  3. Remove the left side plug wires from the retaining clips.
  4. Rotate the engine for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. Remove the right side spark plug wires from the spark plugs.
  6. Remove the plug wires from the retaining clip.
  7. Remove the spark wires from the ignition coils.
  8. Remove the plug wire assembly from the engine.
    NOTE If you are replacing the spark plug wires, the spark plug wire conduit and retaining clips should be transferred to the replacement wires.

To install:
  1. Install the right side plug wires to the ignition coils and then the spark plugs.
  2. Install the spark plug wires to the retaining clip.
  3. Rotate the engine back to the original position.
  4. Install the left side spark plug wires to the ignition coils and then to the spark plugs.
  5. Install the spark plug wires to the retaining clips.

3.9L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the intake manifold cover.
  3. Remove the left side spark plug wires as follows:
    1. Disconnect the left side spark plug wires from the spark plugs.
    2. Disconnect the left side spark plug wires from the ignition coil.
    3. Remove the left side spark plug wire clips from the intake manifold and heater inlet and outlet pipe.
    4. Remove the left side spark plug wire assembly.

  4. If removing the right side spark plug wires, the engine must be rotated for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. After rotating the engine, remove the right side spark plug wires as follows:
    1. Disconnect the right side spark plug wires from the spark plugs and ignition coil.

  6. Remove the right side spark plug wire clip from the ignition coil bracket.
  7. Remove the right side spark plug wire assembly.

To install:
  1. Install the spark plug wire assembly.
  2. Install the right side spark plug wire clip at the ignition coil bracket.
  3. Connect the plug wires to the ignition coil and spark plugs.
  4. If the engine was rotated for access, return the engine to the original position.
  5. The remainder of the installation is the reverse order of removal.

Feb 05, 2011 | 2000 Pontiac Montana

1 Answer

Where are you spark plugs on a 2006 Ford Fusion. I have changed many vehicles Spark Plugs but Im not familiar with this model and do I have to remove the intake manifold to get to them ???



Inspection & Gapping

Fig. Inspect the spark plug to determine engine running conditions


Removal & Installation

2.3L Engine

  1. Disconnect the negative battery cable.
  2. Remove the 2 nuts, the bolt and the alternator air inlet duct.

    0996b43f807cb98c.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Remove the 2 nuts, the bolt and the alternator air inlet duct-2.3L engine

  3. Disconnect the 4 ignition coil-on-plug electrical connectors.
    NOTE When removing the ignition coil-on-plugs, a slight twisting motion will break the seal and ease removal. Remove the 4 bolts and the ignition coil-on-plugs.

    WARNING Only use hand tools when removing or installing the spark plugs, or damage can occur to the cylinder head or spark plug.

    NOTE Use compressed air to remove any foreign material in the spark plug well before removing the spark plugs.
  4. Remove the 4 spark plugs.

To install:
  1. Inspect the spark plugs, as outlined in this section.
  2. Adjust the spark plug gap, as necessary, to 1.25-1.35mm (0.049-0.053 in.).
    WARNING Only use hand tools when removing or installing the spark plugs, or damage can occur to the cylinder head or spark plug.
  3. Install the spark plugs and tighten to 12 Nm (9 lb-ft).
    NOTE Apply a small amount of dielectric grease to the inside of the ignition coil-on-plug boots before attaching to the spark plugs.
  4. Install the 4 ignition coils and bolts and tighten to 10 Nm (89 lb-in).
  5. Connect the 4 ignition coil electrical connectors.
  6. Install the alternator air inlet duct and the 2 nuts and the bolt. Tighten to 6 Nm (53 lb-in).
  7. Connect the negative battery cable.

Oct 12, 2010 | 2004 Toyota Corolla

2 Answers

Where are the spark plugs located on the car


They are underneath the coils,there will be a coil,and under the coil will be a spark plug boot connecting the coil to the spark plug.

Oct 30, 2009 | 2001 Oldsmobile Intrigue

1 Answer

Replacing spark plugs on a 2004 chevy malibu


2.2L Engine
  1. Observe the following service precautions:

    Allow the engine to cool before removing the spark plugs. Attempting to remove spark plugs from a hot engine can cause the spark plugs to seize. This can damage the cylinder head threads. Clean the spark plug recess area before removing the spark plug. Failure to do so can result in engine damage due to dirt or foreign material entering the cylinder head, or in contamination of the cylinder head threads. Contaminated threads may prevent proper seating of the new spark plug. Use only the spark plugs specified for use in the vehicle. Do not install spark plugs that are either hotter or colder than those specified for the vehicle. Installing spark plugs of another type can severely damage the engine.
  2. Turn the ignition OFF .
  3. Disconnect the Electronic Ignition (EI) module harness connector.
  4. Remove the spark plugs using a 5 / 8 inch spark plug socket.

To install:

WARNING Do not coat spark plug threads with anti-seize compound. If anti-seize compound is used and spark plugs are over-torqued, damage to the cylinder head threads may result.
  1. Inspect the gap on the new spark plugs, re-gap the plugs as required. The spark plug gap specification is 42 inch. (1.0 mm).
  2. Install the spark plugs and tighten to 15 ft. lbs. (20 Nm).
  3. Apply dielectric compound to the spark plug boots and make sure no corrosion is present.
  4. Install the ignition coil housing to cam cover and attachment bolts.
  5. Tighten the ignition coil housing bolts to 89 inch. lbs. (10 Nm).
  6. Connect the EI module harness connector. Push in until a click is heard and pull back to confirm a positive engagement.

Oct 07, 2009 | 2004 Chevrolet Malibu

1 Answer

I need the diagram to put the spark plug cables


2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
  2. Remove the intake manifold cover, if required.
  3. Disconnect the left side spark plug wires from the spark plugs.
  4. Disconnect the left side spark plug wires from the ignition coil.
  5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
  6. Remove the spark plug wire assembly.
  7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
  8. Disconnect the right side spark plug wires from the spark plugs.
  9. Disconnect the right side spark plugs from the ignition coils.
  10. Remove the spark plug wire assembly.
  11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.
To install:
  1. Install the spark plug wire assembly.
  2. Connect the right side spark plugs to the ignition coils.
  3. Connect the right side spark plug wires to the spark plugs.
  4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
  5. Install the spark plug wire assembly.
  6. Connect the left side spark plug wires to the spark plugs.
  7. Connect the left side spark plug wires to the ignition coil.
  8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
  9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
  10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
74d742b.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
306b531.jpg


Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
9313fa7.jpg


Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system
2c9af72.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
d929c16.jpg


Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
f357cd3.jpg

Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system
09e9db9.jpg

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 2003 Chevrolet Malibu

1 Answer

Where are the spark plugs on my 2000 Oldsmobile Intrigue and how do i change them?


2000 Oldsmobile Intrigue V6-214 3.5L VIN H SFI

Spark Plug: Service and Repair
REMOVAL PROCEDURE
TOOLS REQUIRED
J 43094 Spark Plug Boot Puller
1. Turn OFF the ignition switch.
2. Remove the ignition coil assembly.
3. Use the J 43094 in order to remove the spark plug boots from the spark plugs.
NOTE: Allow the engine to cool before removing the spark plugs. Attempting to remove the spark plugs from a hot engine may cause the plug
threads to seize causing damage to cylinder head threads.
NOTE: Clean the spark plug recess area before removing the spark plug. Failure to do so could result in engine damage because of dirt or
foreign material entering the cylinder head, or by the contamination of the cylinder head threads. The contaminated threads may prevent the
proper seating of the new plug. Use a thread chaser to clean the threads of any contamination.
4. Remove the spark plugs from the engine.
INSTALLATION PROCEDURE
NOTE: Use only the spark plugs specified for use in the vehicle. Do not install spark plugs that are either hotter or colder than those specified for the
vehicle. Installing spark plugs of another type can severely damage the engine.
NOTE: Check the gap of all new and reconditioned spark plugs before installation. The pre-set gaps may have changed during handling. Use a round
feeler gage to ensure an accurate check. Installing the spark plugs with the wrong gap can cause poor engine performance and may even damage the
engine.
1. Measure the spark plug gap on the spark plugs to be installed. Compare the measurement to the gap specifications. Refer to Spark Plug Usage.
Correct as necessary.
NOTE: Be sure that the spark plug threads smoothly into the cylinder head and the spark plug is fully seated. Use a thread chaser, if necessary,
to clean threads in the cylinder head. Cross-threading or failing to fully seat the spark plug can cause overheating of the plug, exhaust blow-by, or
thread damage.
NOTE: Refer to Fastener Notice in Service Precautions.
2. Install the spark plugs to the engine.
Tighten
Tighten the spark plug to 20 N.m (15 lb ft).
3. Install the spark plug boots to the ignition coil assembly.

5c212b8.jpg
4. Install the ignition coil assembly.

Sep 13, 2009 | 2000 Oldsmobile Intrigue

2 Answers

How to replace sparl plugs on a Jeep Cherokee?


Hello, I hope this info helps...(subytech1)...REMOVAL
In this engine, each individual spark plug is located under each ignition coil.

  1. Prior to removing spark plug, spray compressed air around base ofignition coil at cylinder head. This will help prevent foreign materialfrom entering combustion chamber.
  2. On this engine each individual ignition coil must be removedto gain access to each spark plug. Refer to Ignition CoilRemoval/Installation.
  3. Check condition of coil O-ring and replace as necessary.
  1. Inspect spark plug condition. Refer to Spark Plug Conditions.
CLEANING
Theplugs may be cleaned using commercially available spark plug cleaningequipment. After cleaning, file center electrode flat with a smallpoint file or jewelers file before adjusting gap.

CAUTION: Never use a motorized wire wheel brush to clean sparkplugs. Metallic deposits will remain on spark plug insulator and willcause plug misfire.

ADJUSTMENT

Setting Spark Plug Gap - Typical
Check spark plug gap with a gap gauge tool. If the gap is not correct,adjust it by bending ground electrode. Never attempt to adjust gap bybending center electrode.

INSTALLATION

CAUTION: This engine is equipped with copper core groundelectrode spark plugs. They must be replaced with the same type/numberspark plug as the original. If another spark plug is substituted,pre-ignition will result.

Special care should be taken when installing spark plugs into cylinderhead spark plug wells. Be sure plugs do not drop into plug wells asground straps may be bent resulting in a change in plug gap, orelectrodes can be damaged.

Always tighten spark plugs to specified torque. Over tightening cancause distortion resulting in a change in spark plug gap or a crackedporcelain insulator.

  1. Start spark plug into cylinder head by hand to avoid cross threading.
  2. Tighten spark plugs to 27 Nm (20 ft. lbs.) torque.
  3. Before installing coil(s), check condition of coil O-ring andreplace as necessary. To aid in coil installation, apply silicone tocoil O-ring.
  4. Install ignition coil(s). Refer to Ignition Coil Removal/Installation.

Aug 07, 2009 | 2000 Jeep Grand Cherokee

1 Answer

How do I change spark plugs on 2000 VW jetta 2.0 engine


Here is a diagram and step to step to take out your spark plugs and re-install them. Please do not forget to rate and comment about yor experience with fixya today

2.0L (Aeg, Avh, Azg, Bbw, Bev) Engines
NOTE This procedure requires the use of the following special tools, or their equivalents:

  • Spark plug wrench VAS 3122B
  • Seal puller T10018
  • Removal/Installation tool T10029
  • Puller T10095
  • Torque wrench V.A.G 1331/ (5 - 50 Nm)
  1. Make sure you have the radio code, if necessary.
  2. Disconnect the negative battery cable.
  3. Pry the plugs out (arrows), then remove the nuts underneath.
  4. Remove the nut (1).
    42075_vwca_g0016.gif Pry the plugs out (arrows), then remove the nuts underneath. Remove the nut (1)
  5. Pull out oil dipstick.
  6. Remove engine cover.
    42075_vwca_g0018.gif Spark plug applications—2.0L (AEG, AVH, AZG, BBW, BEV) Engines
  7. Remove the spark plug connector (arrows) using tool T10029.
  8. Remove the spark plug using Spark plug wrench VAS 3122B.
  9. Inspect the spark plugs, as outlined in this section.
    42075_vwca_g0017.gif Remove the spark plug connector (arrows) using tool T10029 and remove the spark plug using Spark plug wrench VAS 3122B (arrow)
To install:
  1. Install spark plugs with Spark plug wrench VAS 3122B. Tighten to 22 ft. lbs (30 Nm).
  2. Install spark plug connectors using Removal/Installation tool T10029
  3. Check that ignition wiring and spark plug connectors are seated securely.
  4. Install engine compartment cover.
  5. Connect the negative battery cable.

Apr 15, 2009 | 2000 Volkswagen Jetta TDI

Not finding what you are looking for?
2004 Ford F150 Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5579 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...