Question about 2004 Ford Escape

Open Question

How do you remove the rear wiper arm and motor

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75822 Answers

SOURCE: Windshield Wiper Arm

Pull up on the wiper arm, you will see a tiny little blade on the side of the wiper arm where it goes over the post, take a little screwdriver and pry that out board, this will release the arm from the post, it will be tight, wiggle the arm and pull straight out away from the post.

Posted on Oct 19, 2008

mastatech
  • 478 Answers

SOURCE: Removing 2004 Lexus RX330 Rear Wiper Arm

Use liquid wrench it will free up the corrosion, its the best, in every mechanics tools.

Posted on Mar 28, 2009

chuck943
  • 783 Answers

SOURCE: How do I remove the rear wiper arm on my 1996 Ford Explorer?

Pull the wiper arm away from the glass until it is straight out. Then take a small flat blade screw driver and release the retaining clip at the base of the pivot arm. The carefully pry the pivot arm from the shaft.

Posted on Apr 15, 2009

  • 3600 Answers

SOURCE: removal of broken rear wiper arm. removed nut but

After removing the nut turn the arm up and wiggle it back and forth while pulling it will come off.

Posted on Oct 11, 2009

Testimonial: "Thank you for the advice. You saved me labor cost at the dealer and waiting around for the repair."

kennyz195
  • 61 Answers

SOURCE: replace rear wiper arm

there is a cover at the base lift it up and then you have a nut. 10mm remove this and pull off the arm. sometime they get stuck and you will have to pry it up.

Posted on Apr 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW DO YOU REPLACE THE REAR WIPER MOTOR ON A 2007 chevrolet uplander


1. Remove the rear wiper arm 2. Remove the wiper driveshaft nut( nut behind wiper arm) and the washer and seal from the driveshaft 3. Remove liftgate trim pannel 4. Dissconect electrical conn and retaining screws from the motor. Reverse to install. But my advice is put the motor in but leave arm off, run the wiper motor to make sure it is working and to make sure it is at its resting spot. Then put the arm back on.

Nov 26, 2013 | 2007 Chevrolet Uplander

1 Answer

02 liberty rear wiper dose not work plugin has power changed wiper motor still doses work


There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

zjlimited_494.gif

1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..

zjlimited_495.gif

1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

Jul 19, 2011 | 2002 Jeep Liberty

2 Answers

How do I fix or replace the rear wiper motor


Hello,

  1. Disconnect the cable running to the negative terminal on the car's battery. To do this, loosen the nut on the cable clamp until the clamp is loose enough for you to slide the cable clamp off the negative battery terminal.
  2. Pull the wiper arm away from the rear windshield until the wiper arm locks into a vertical or semi-vertical position or is perpendicular to the rear windshield.
  3. Remove the nut holding the wiper arm assembly to the rear wiper motor.
  4. Pull the wiper arm off the wiper motor assembly.
  5. Unplug the rear wiper motor plug/harness.
  6. Remove the screws holding the rear wiper motor to the inside of the vehicle at the base of the rear window.
  7. Pull the rear wiper motor off.
  8. Install the new wiper motor and put the wiper motor and arm assembly back on the vehicle by reversing the completed steps.
From ehow.com

I hope this helps

Mar 21, 2011 | 2000 Ford Expedition

1 Answer

I remove the wiper arm & the outsdie lock of the shaft,remove the screws that hold the wiper motor inside, to I need to remove the 20mm nuts that hold the rubber seal outside the glass (in which I can...


IF YOU TALKING ABOUT REAR WIPER MOTOR REMOVAL YOU HAVE TO REMOVE PULL THE REAR WIPER ARM COVER BACK TO ACCESS THE WIPER ARM RETAINING NUT.DETACH THE NUT AND PULL WIPER ARM STRAIGHT OFF THE SHAFT TO REMOVE IT.

Nov 26, 2010 | 2000 Honda Odyssey

1 Answer

Wipers will not move, makes noise and there is power to the motor. Motor was replaced. Someone told me that the arms probably moved to far and are now stuck, how do I fix this?


Windshield Wiper Blade & Arm Removal & Installation Front To Remove:
  1. Mark the location of the wiper on the windshield.
  2. Remove or disconnect the following:
    • Nut cover
    • Nut from the wiper arm
    • Wiper arm
Wiper arm mounting nut gm_truck_s10_w-wpr-arm_ret-nt.gif
To Install:
  1. Install or connect the following:
    • Secure the wiper arm with the nut.
      1. Tighten to: 17 ft-lb (23 Nm)
    • Nut cover
Rear To Remove:
  1. Put the wiper arm in the park position.
  2. Remove or disconnect the following:
    • The washer hose from the connector
    • The cap from the wiper arm
    • The nut from the wiper arm
    • The wiper arm from the wiper motor shaft
Rear wiper arm mounting nut gm_truck_s10_w-wpr-arm_ret-nt_rr.gif
To Install:
  1. Install or connect the following:
    • The wiper arm on the wiper motor shaft in the park position with the wiper arm resting on the park ramp
    • The nut on the wiper arm
      1. Tighten the nut. Torque to: 17 ft lbs (23 nm)
    • The cap on the wiper arm
    • The washer hose on the connector

---
The wiper motor hopefully is ok, but if the wiper arms were not mounted at the right spot, it could have damaged the motor as it returned to the rest position, unfortunately.

If there is noise, the noise could be coming from the wiper arm joint being stripped out or the motor itself assuming that the ball joints under the hood and behind the firewall are still connected.

Check these items, and I'm sure you will get to the bottom of this.

Good luck on this repair.

Oct 08, 2010 | 1997 Chevrolet Blazer

1 Answer

I installed a new wiper motor. I ran it before installing the wiper arms. it will not stop at zero. it over travels down into the cowling. I try to rest them higher then they stop some where in the middle...


Try to run the motor without the wiper arms tightened down and turn it off so it can cycle down to its rest state. Then install the wiper arms.

Make sure, that the car's windshield wiper wiring is correct for this motor.
---
Wiper Arm & Blade Removal & Installation Front To Remove:
CAUTION
When the wipers are parked (off), the driver’s wiper arm must be above the passenger’s wiper arm.
  1. Remove the clip holding the outside end of the wiper arm cover to the arm.
  2. Lift the arm cap up to expose the nut.
  3. Remove the wiper arm mounting nut.
  4. Using a suitable two jaw puller, remove the wiper arm from the wiper pivot.
To Install:
  1. Verify that the wiper motor and linkage are in the parked position.
  2. Place the wiper arm in position over the wiper pivot.
  3. Install the nut to hold the wiper arm to the wiper pivot. Torque nut to 26 ft. lbs. (35 Nm). CAUTION
    Make sure to tighten the wiper arm nut properly.
  4. Push the arm cap cover down.
  5. Secure the clip holding the cover to the wiper arm.
Rear To Remove:
  1. Lift and hold the wiper arm away from the rear window.
  2. Lift the lock securing the wiper arm to the pivot.
  3. Slowly release the wiper arm so it rests against the lock.
  4. Remove the wiper arm from the pivot.
To Install:
  1. Install the wiper arm on the pivot.
  2. Pull the arm outward and release the lock.
  3. Gently release the wiper arm until it rests on the rear window.
prev.gif next.gif

Aug 22, 2010 | 1996 Dodge Grand Caravan

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

1 Answer

HOW DO I REPLACE A REAR WINDOW WIPER ON 2005 FORD ESCAPE?


Remove the rear pivot arm.
Lift the pivot arm to the upright position.
Slide the locking tab out.
Pull up and remove the pivot arm.
Remove the rear wiper motor shaft nut cover.
Remove the rear wiper motor shaft nut.
Remove the rear wiper motor cover.
Remove the rear wiper motor bracket nut.
Remove the bolt and the rear wiper motor.

Jan 29, 2009 | 2005 Ford Escape

1 Answer

Driver's side wiper arm on my '93 Sidekick is not working


This is what I Found there was not any Illustration's with it looks Fairly simple, Good luck



FRONT
  1. Disconnect linkage assembly from wiper motor shaft.
  2. Disconnect electrical connectors from wiper motor.
  3. Remove wiper motor attaching bolts, then wiper motor.
REAR
  1. Remove wiper blade and arm assembly.
  2. Remove access panel on back door.
  3. Disconnect linkage assembly from wiper motor shaft.
  4. Disconnect electrical connectors from wiper motor.
  5. Remove wiper motor attaching bolts, then wiper motor.
Skill
Level
Mfg.
Warranty
Standard Wiper Motor Labor Replace Front B 0.7 1.0
PLEASE DONT FORGET TO RATE ME Thank You Much

Jan 20, 2009 | 1995 Suzuki Sidekick

1 Answer

I have a 1998 Ford Explorer.


  1. Remove the rear pivot arm; refer to Pivot Arm—Rear . 7981ec7.gif
  2. Remove rear pivot arm.
    1. Lift the pivot arm nut cover.
    1. Remove the nut.
    1. Remove the pivot arm.
  1. Remove the liftgate door trim panel; refer to Section 501-05 . Remove the (A) liftgate handle to liftgate screws and the (B) liftgate handle. Remove the liftgate trim panel screw access plug. Remove the screw.
  2. Remove the liftgate door trim panel.
    1. Use Windshield and Molding/Trim Removal Kit to remove the liftgate door trim panel from the liftgate window opening.
    1. Push the liftgate door trim panel toward the top of the liftgate and remove the liftgate trim panel. 9e75e00.gif
  1. Position the watershield aside to gain access to the rear wiper motor.
  1. Remove rear wiper motor.
    • Disconnect electrical connector.
    • Remove three retaining bolts.
    • Remove rear wiper motor.
good luck.

Jan 10, 2009 | 1998 Ford Explorer

Not finding what you are looking for?
2004 Ford Escape Logo

Related Topics:

1,081 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...