Question about 2000 Jaguar XK

1 Answer

How do You remove the plastic clips to pull the air intake tube

How do You remove the plastic clips to pull the hose from the air intake tube that goes to the valve cover. I want to remove the top of the air box to replace the air filter and at the same time get the plastic air intake cover out of the way to get to some coolant hoses that are leaking. I want to remove the section from the top of the air cleaner to the top of the throttle body. There are 2 bolts that connect this intake tube to the throttle body the air cleaner top is held on by metal clips that pop off but the hose to the valve cover has plastic clips surrounding the end of the hose. I don't want to break them off. Thanks for Your Time Johnny B 2000 Jag xkr

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Jaguar Master
  • 716 Answers

Thats the part load breather pipe. you should be able to remove it by squeezing the plastic clip together by hand but it may have hardened by age making it difficult and can break be carefull not to break the stub on the cam /valve cover if in doubt cut the pipe off carefully and fit a new one. by gentle twisting/squeezing they nomally come off

Posted on Apr 04, 2017

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 12 Answers

SOURCE: I REPLACED THE VALVE COVER GASKETS AND CROSSED A COOLANT HOSE WITH A PVC HOSE WICH PULLED COOLANT IN THE CYLINDERS REPAIRED THAT PROBLEM BUT NOW HAVE A NOISE THAT SOUNDS LIKE A LIFTER

step 1Materials Valve Cover Gasket Kit ($13 at autozone, big box with two tubes of RTV and 11 neoprene bolt seals) --- alternatively, you can buy the preformed gasket for about $30 - if y…

step 2Remove the intake You'll need your screwdriver to loosen up any clamps. You really only need to remove the section that bolts up to the TB -- this just makes working faster. If you d…

step 3Remove Solenoid I think its an EGR solenoid - regardless, its bolted on to the side of the valve cover. If you can unplug it - be my guest. I couldn't, so I used a socket and unbolted it.

step 4Remove Spark Plug Wires etc. Pull the wires. Also disconnect the PCV canister and breather hose.

step 5Remove Valve Cover Bolts and remove the valve cover Using the Torx bit, remove the valve cover bolts and their gasket washer ring thingies. I think they are all the same size, so no worries about keeping them in order. Th…

step 6Optional - **** out any oil If your gasket failed like mine, you're gonna need to pull some excess oil out of the plug wells. A plastic turkey baster comes in handy here :P I used a pipette - it is wh…

step 7Clean the Mating Surfaces Using the gasket scrapper, remove any and ALL of the old gasket material. Using a #1 (or maybe #2) flat head screwdriver will help get the old material out of the groove…

step 8Apply the RTV Gasket Material Follow the directions on the tube of RTV. Evenly apply a bead of RTV sealant on the valve cover. I added a little extra to the #1 and #2 spark plug well. I did this because…

step 9Put the valve cover back on This is important. Place the valve cover back on the head exactly where you want it without hitting anything. If you smear the wet RTV, you're going to have to clean it off…

step 10Final Steps Now you're pretty much done. Using your socket, replace that solenoid and any hoses you took off. Replace the intake, breather hose and PCV line. Then let your car sit f…

Posted on May 29, 2009

jmgldsmth
  • 1869 Answers

SOURCE: Procedure for inspection of lifters or R&R on cylinder head....

I see now;
do a compression check on the cylinders
this will answer the question if a lifter or, valve is damaged the cylinder pressure will be low

Posted on May 29, 2009

gordanddar
  • 477 Answers

SOURCE: 2007 jag xkr w/ 18,000 mi check engine light just

To many to list. Could be something as simple as a loose gas cap.
Have someone check for trouble codes with a diagnostic computer.

Double check your manual. Is this a check engine light , or a service engine soon light. The former is a sign of trouble , the later is just a reminder to have your scheduled service done.

Posted on Nov 06, 2009

swolfinor
  • 504 Answers

SOURCE: How to program garage door, jag xkr '07

GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Posted on May 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Locate pcv valve.pulled throtle body nothing or valve covers


Crankcase ventilation system is used to consume crankcase vapors created during the combustion process instead of venting them to the atmosphere.
Fresh air is supplied through a filter to the crankcase, the crankcase mixes the fresh air with the blow-by gases and then passed through a positive crankcase ventilation (PCV) orificed tube into the intake manifold.
The PCV orificed tube restricts the flow rate of the blow-by gases using a 3 mm (0.118 in) (a) orifice located at the end of the tube. If abnormal operating conditions arise, the system is designed to allow excessive amounts of blow-by gases to back flow through the crankcase vent tube into the throttle body in order to be consumed by normal combustion. Positive Crankcase Ventilation Hose/Pipe/Tube Replacement
Remove the two nuts (2) from the fuel injector sight shield (1).
Lift the sight shield (1) from the front and pull forward to disengage the rear tab from the bracket.
Disconnect the PCV fresh air tube from the left camshaft cover.
Remove the PCV fresh air tube from the throttle body.
Remove the drive belt. Refer to Drive Belt Replacement .
Remove the power steering pump retaining bolt.
With the hoses still attached, Carefully position aside the power steering pump.
Remove the retaining clip securing the PCV dirty air tube.
Disconnect the PCV dirty air tube from the PCV orificed tube.
Remove the PCV dirty air tube from the intake manifold.

Feb 25, 2016 | 2004 Cadillac Seville

Tip

Replacing spark plugs and coils on Mazda Tribute V6


Here are DIY step by step instructions for replacing the spark plugs and / or coils in a Mazda Tribute V6 (based on a 2001 Tribute).

This is a lengthy procedure, but don't be frightened, it works...I have done it a few times. This will save you a few hundred $$$ if you do it yourself. Make sure to read all of these instructions, preferably while looking at your engine, before you get started. You will need 2-3 hours to do this job.

NOTE 1: IF YOU HAVE A SPECIFIC ISSUE WITH CYLINDERS/COILS 4, 5, OR 6, YOU ARE IN LUCK, YOU ONLY HAVE TO REMOVE A PLASTIC ENGINE COVER. IF YOUR ISSUE IS WITH CYLINDERS/COILS 1, 2 OR 3, OR YOU ARE CHANGING ALL OF THE SPARK PLUGS, YOU WILL HAVE TO REMOVE THE INTAKE MANIFOLD. THESE INSTRUCTIONS COVER CHANGING ALL OF THE SPARK PLUGS AND CAN BE USED TO REPLACE ANY OF THE COILS.

NOTE 2: IF YOU ARE THINKING OF REPLACING YOUR SPARKPLUGS BECAUSE YOUR ENGINE IS RUNNING ROUGH, PLEASE DO YOURSELF A FAVOR AND GET THE ENGINE SCANNED FIRST TO MAKE SURE THAT A COIL IS NOT THE ISSUE. YOU CAN REPLACE YOUR PLUGS AND BAD COILS AT THE SAME TIME WITH THIS PROCEDURE. YOU WILL BE UPSET IF YOU DO THIS WORK TO REPLACE ONLY YOUR SPARKPLUGS, THEN YOU FIND OUT AFTERWARDS THAT A COIL WAS BAD AND YOU HAVE TO DO IT AGAIN LIKE I DID.

1. Tools: Pliers, ratchet wrench, ratchet wrench socket extension, 8 mm socket, 10 mm socket, Spark plug socket, flat head screw driver, plastic zip tie, plastic cup or bowl. Not necessary, but very helpful: Magnet on an antenna to pick up dropped nuts/bolts.

2. All directions are given from a point of reference as if standing in front of the car, except for removing the coils and plugs from firewall (back) side of the engine.

3. Using flat head screwdriver, loosen band clamp on large rubber air intake hose where it connects to the intake manifold on the right side of the engine. Slowly work rubber intake hose off of intake manifold.

4. Unplug wires from back side of air idler valve - small unpainted metal part mounted on top of air intake on manifold (close to where the air intake hose connects to intake manifold).

5. Disconnect small rubber hose from top of the ERG valve (black metal disk near back right side of manifold.

6. Remove the two bolts that hold ERG valve to manifold bracket. Use the 10 mm socket and ratchet to remove these. If you are trying to remove the 8 mm bolts, you are removing the wrong bracket. Be careful, there is a gasket between the manifold and the ERG valve, make sure it does not fall out when removing bolts. Place bolts and gasket in cup.

7. There is a small plastic sensor just to the left of the ERG valve towards the back of the engine. If you look at how the sensor is attached to the manifold, you will see that the back left side bolt that holds this sensor, also connects the intake manifold to a plastic wiring harness at the firewall. You will need to remove the 8 mm nut from this bolt to free up the intake manifold in a later step. Now remove 8 mm bolt from other side of sensor. Might need the socket extension to remove these. Place nut and bolt in cup.

8. Unplug wires from the back of the sensor discussed in the previous step (7).

9. There are 3 hoses of different sizes plugged into the back of the manifold. Unplug all three hoses from manifold. Remove zip ties if needed to slide hoses off. Left hose may have a compression clamp, use pliers to loosen clamp while sliding hose off.

10 There are two large black plastic wiring connectors supported by the back left side of the manifold. They are supported by plastic clips with plastic barbs. Use the flat head screw driver to pry off the support clips from the manifold - don't worry, you won't break them. You will be able to plug them back in later.

11. There are still a few things attached to the intake manifold, but there will be enough flexibility now to lift up the manifold and replace the spark plugs.

12. Remove the plastic engine cover - there are three 8 mm nuts to remove. You will need the socket extension. One the nuts are removed, you will have to wiggle the cover off especially on right side. Place nuts in cup.

13. The plastic intake manifold on top of the engine is now exposed. If you look down at the front side of the engine, you will see the coils for cylinders 4, 5 and 6 (going from left to right). The tops of the coils will probably say "Motorcraft" on them. Also, there are two cables attached to the top of the manifold - leave them alone.

14. There are 8 bolts that hold the intake manifold down. The bolts are located in two rows of 4 across the top of the manifold. Loosen them all using the 8 mm socket with extension. Note: these bolts do not come completely out when fully loosened.

15. Slowly work the intake manifold loose by lifting up on each side. NOTE: Work the manifold off of the bolt discussed in step 7 (back right side of manifold), NOTE: Work slowly watching for anything that might be hanging up. You should eventually be able to get about 4" of clearance between the back right side of the manifold and engine, and 8-10" of clearance on the back left side. Move around to the passenger side to help lift off the manifold. While working on the back side plugs, you will stand on the passenger side of the car.

16. Once you are able to lift up the manifold, get a cup, block of wood, anything suitable approx. 5" tall to prop up the manifold (place under center of manifold). This will keep the manifold off your hands while you are working.

17. The three coils on the back side of the engine are now visible if you are standing on the passenger side of the car (cylinders 1, 2 and 3) Cylinder 1 is closest to you - passenger side, cylinder 3 is furthest from you - driver side.

18. Each coil has one 8 mm bolt holding it down. Take the 8 mm socket and ratchet and remove the bolts from the 3 coils on the back side of the engine. Place bolts in cup.

19. Lift each coil away from engine (do not pull on wires plugged into the coil). Pull each coil's silicon rubber tube out of spark plug hole, bend tube to get it out without pulling on the coil wiring. Leave coils plugged in and lay them to the side. NOTE: If you are looking to replace a coil (or coils) simply unplug the coil wires from the old coil, and plug into new coil at this stage.

20. Using sparkplug socket and socket extension, remove each of the back 3 spark plugs.

21. Install the new spark plugs (gap them first if they are gap type).

22. Slide each coil rubber tube back into sparkplug hole and bolt down coil (8 mm bolt). Congratulations! The hard part is over with!

23. Make sure the rectangular intake port gaskets are clean on the engine (before lowering the intake manifold back down).

24. Slowly work the intake manifold back down to the top of the engine - make sure that the manifold is back on the bold discussed in step 7, and that nothing is binding.

25. Bolt the manifold back down (eight bolts, 8 mm, still attached to the manifold). Use 8 mm socket with extension. Gradually tighten the bolts going from bolt to bolt until they are all tight (don't fully tighten one bolt first).

26. Remove coils and spark plugs on front side of engine. Replace spark plugs and re-install coils. Same procedure as back side of engine, but much easier. Replace coil(s) if desired.

27. Re-install the two plastic wiring connector support clips to the left side of the manifold - push barbed clips into manifold.

28. Reconnect 3 hoses to back side of manifold. Place new plastic zip tie on hose that had zip tie.

29. Reinstall plastic sensor on back right side of manifold (8 mm nut and 8 mm bolt).

30. Plug in wires back into back side of plastic sensor.

31. Reinstall 10 mm bolts and gasket on ERG valve and tighten to manifold.

32. Reconnect small rubber hose to top of ERG valve.

33. Reconnect large air intake hose to intake manifold and tighten hose clamp using flathead screwdriver.

34. Plug wires back into back of idle air control valve (this was uplugged in step 4).

35. Leave the plastic engine cover off for now. Check all around the manifold and make sure everything is reconnected.

36. Start engine - should start and run normally (or better). If not, go to trouble shooting at the end.

37. Reinstall plastic engine cover (three 8 mm nuts). Make sure engine is not running when reinstalling plastic cover.

TROUBLE SHOOTING: If engine light comes on (and wasn't on before changing plugs), or if engine runs rough, stop engine and double check that all wires and hoses are plugged back in. If you find wires or hose left disconnected, reconnect them. Disconnect car battery for a few minutes then reconnect (to clear out engine alarm). Restart car, engine should run well, engine light should be cleared.

on May 01, 2010 | Mazda Tribute Cars & Trucks

1 Answer

How to remove a radiator


Engine is cool!

drain coolant drain cock is at lower driver side .remove air cleaner.remove the electrical conaction.

remove right side diagonal brace remove upper radiator support and rotate reward remove the upper radiator hose remove upper radiator mount remove cooling fan shroud bolts "disconnect outlet hose from the water pump raise the vehicle disconnect outlet hose from the radiator

disconnect oil cooler hoses from top side of the radiator as follows

disengage the plastic cap from the quick connect fitting pull the plastic cap back along the pipe hold one leg of retaining clip

using a small bent screwdriver gently disengage the other end of the retaining clip from the quick content fitting rotate the retaining clip out of the quick connect fitting remove the retaining clip completely

remove the nut which secures the AC discharge hose remove the inlet tube remove radiator and condenser assembly

(Try to remove the radiator and keep the AC condenser In place)

Jul 16, 2014 | 2003 Buick Rendezvous

2 Answers

How do I change the air filter, not air conditioning filter, for the engine on a 2005 Crossfire?


The air filter is in the air intake box (usualy square plastic tub) under the hood. A couple of clips unsnap and the top comes off. Replace the element inside.

Mar 14, 2011 | 2005 Chrysler Crossfire

1 Answer

How replace intake gaskets focus 2000


SECTION 303-01B: Engine - 2.0L SPI 2000 Focus Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/5/2001 Intake Manifold
Special Tool(s) 412108.jpg Remover/Installer, hose clamp
412-108 (T96P-18539-A) Removal
  1. Release the fuel pressure. For additional information, refer to Section 310-00.
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02.
  1. Detach the intake manifold bracket.
    • Loosen the nuts and remove the bolts.
    e0008065.jpg
  1. Lower the vehicle.
  1. Remove the air cleaner housing.
    1. Disconnect the mass air flow (MAF) sensor electrical connector.
    1. Disconnect the air cleaner outlet hose.
    • Remove the air cleaner housing from the rubber bushing.
    e0009092.jpg
  1. Disconnect the accelerator cable.
    1. Unhook the cable.
    1. Remove the plastic clip and position the accelerator cable to one side.
    e0009093.jpg
  1. Disconnect the speed control cable.
    1. Unhook the cable.
    1. Remove the plastic clip and position the speed control cable to one side.
    e0009094.jpg
  1. Disconnect the positive crankcase ventilation hoses.
    e0009794.jpg
  1. Disconnect the vacuum hoses.
    1. EVAP solenoid valve.
    1. Brake booster.
    1. Delta pressure feedback electronic (DPFE) system sensor.
    1. Exhaust gas recirculation (EGR) valve.
    e0009099.jpg
  1. Disconnect the EGR valve.
    • Discard the gasket.
    e0009351.jpg
  1. NOTE: Clamp the hoses to prevent coolant loss.
    Disconnect the coolant hoses from the intake manifold.
    e0024942.jpg
  1. Remove the vacuum hose assembly.
    e0009101.jpg
  1. Disconnect the throttle position (TP) sensor and the idle air control (IAC) valve.
    e0009353.jpg
  1. NOTE: Do not remove the oil level indicator tube.
    Remove the bolt and bracket from the oil level indicator tube.
    e0008058.jpg
  1. Remove the intake manifold upper support bracket.
    e0024943.jpg
  1. Disconnect the fuel injector electrical connectors.
    e0018167.jpg
  1. Disconnect the electrical connectors.
    1. Intake manifold runner control (IMRC).
    1. Camshaft position (CMP) sensor.
    1. Ignition Coil.
    e0024941.jpg
  1. Disconnect the fuel lines from the fuel rail. For additional information, refer to Section 310-00.
  1. Remove the intake manifold retainers and position the manifold to the rear of the engine compartment (shown with engine removed).
    e0009357.jpg
  1. Remove the IMRC manifolds (shown with engine removed).
    • Remove the two studs first.
    • Discard the gaskets.
    e0028869.jpg
  1. Remove the intake manifold from the engine compartment.
    e0028727.jpg

Mar 08, 2011 | 2000 Ford Focus

1 Answer

Thermostat replacement


HI there,

Well first of all you may please follow the steps below -

1. Remove the upper radiator hose from the thermostat intake tube by loosening the retaining clip with a screwdriver. Slide the clip toward the radiator and pull the hose off the thermostat intake tube. 2. Remove the two 10-mm bolts that hold the thermostat intake tube onto the intake manifold of the Hyundai Accent. Pull the intake tube off the intake manifold and inspect it for cracks. If any cracks are present, then you need a new thermostat intake tube.
3. Pull the old thermostat and thermostat gasket off the engine with your hands and replace them both with new ones. The thermostat will be marked with "top." This end should stick out of the engine. 4. Place the thermostat intake tube back onto the intake manifold of the Hyundai Accent and bolt it back into place. 5. Slide the radiator hose back on to the thermostat intake tube and secure it in place with the retaining clip. A band clamp can be used in place of the retaining clip for extra clamping pressure. Post comments for further help or information............

Good Luck!!

Thanks for suing FixYa!!

Oct 13, 2010 | 2003 Hyundai Accent

1 Answer

How to replace the air filter on a 2006 tundra


the procedure is as follows:-- Of the top center of the engine is a black plastic intake tube. Follow this tube over to the square plastic air cleaner box assembly. There are snap clips that hold the upper half of the plastic cover on unsnap these clips. The upper half of the air cleaner box will separate allowing you to remove the air filter. The other style has a small lid with two metal snap clips by popping these two metal snap clips back the lid lifts up and the air filter is in place vertically pull up on the air filter and it will come out.
Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

Aug 11, 2010 | 2006 Toyota Tundra

1 Answer

CHANGING SPARK PLUGS 2002 TACOMA 4 CYLINDER


Starting on the pasenger side. Remove the intake tube running from the air filter box to the throttle body and disconnect enough tubes to swing it out of the way. The sparkplugs are down below the small coils you see at the end of the sparkplug wires. With a 10mm socket remove bolt holding the coil, disconnect the plug at the top of the coil by squeezing it at the top and pulling straight off the coils.

Pull the coil straight up. there will be about a 6 inch tube that connects to the top of the spark plug when inserted. You will need a 5/8 sparkplug socket and about 2 feet of extensions to make it easy on yourself. Insert the spark plug socket and extensions down the hole you removed the coils with the tube from and remove and replace the sparkplug. Reinstall your coil onto the engine and move to the next one until you have replaced all the plugs on the passenger side.

Make sure you reconnect all the plugs to the coils, hoses to the intake tube and reinstall your intake tube. The drivers side is a little easier. Pop the spark plug wires from their plastic holders to free enough slack to be able to pull your sparkplug wires out of the block. For the plug closest to the front of the engine you will need to remove the 10mm bolt holding the ground wires to the intake manifold to be able to free enough space for removing the plug.

For the middle plug you will need to remove the 10mm bolt holding the bracket that is holding one of the throttle cables at the top of the intake manifold. For the rear plug just pop the flexible hose that runs behind the black metal bracket straight up out of its clip and push it out of the way along with any other hoses that run through this area. Pull the spark plug wire from its place by pulling straight up just like with the coils. there will also be about a 6 inch tube running down to the spark plug at the bottom of these plugs.

Remove and replace the plugs same as before. make sure you reconnect all your hoses and wires to their previous locations. Doublecheck to make sure you reconnect all the ground wires/ brackets. Also you will need to use " twin ground electrode plugs" (see sticker on front of your plastic timing belt cover? to the right of the radiator hose).

May 27, 2010 | 2002 Toyota Tacoma

1 Answer

How do i change sparkplugs for 2002 mercury couger v6


To remove the spark plugs, remove the covers and you will see how simple it really is. The spark plugs are hiding under the covers.



Not only you will have to lift the covers, but to reach the back three you will have to remove the valve cover. Here's how to:

1. Remove the water pump belt cover (the black cover in the front of the engine compartment that has ?Duratec? on it.) If you have a 1996+ vehicle, you should think about removing it permanently, since it only serves to trap heat and slowly kill the IMRC box electronics.
2. Disconnect the following electrical connectors from the: MAF, IAT, TPS, IAC, and EVR. The EVR connector is black and is located at the very back of the upper plenum, next to the firewall.
3. Disconnect throttle cable from the TB and the cruise control cable, if equipped. For 1995 5-speed vehicles, take care not to lose the metal clip for the throttle cable when you are removing it. Once the cable is removed the clip will slide right off.
4. Disconnect the vacuum lines from the EVR. You may have to wait until the upper intake is unbolted and partially removed for better leverage.
5. Disconnect the vacuum lines from the top of the upper intake. Push down on the black plastic collar with a screwdriver and hold, and then pull the plastic line out of the intake.
6. Remove the air box along with the MAF and accordion tube.
7. Unbolt the throttle cable bracket from the upper intake (three 8mm bolts, one 10mm nut). Set bracket and attached cables aside.
8. Disconnect the air bypass hose at the upper intake. It connects right next to the IAC valve.
9. Disconnect the hose from the PCV valve that goes to the upper intake, underneath the throttle body. This is also a good time to change the PCV valve.
10. Unbolt the EGR valve from the upper intake.
11. Unbolt the upper intake. 12. Carefully remove the upper intake and set it on top of some clean rags or newspaper. It will likely be oozing some oily gunk out the bottom.
13. Cover the openings of the lower intake with clean rags to keep anything from falling into the openings. Anything that falls in will likely end up in the head or the cylinders themselves.
Now you are free to remove the back plugs

May 11, 2010 | 2002 Mercury Cougar

1 Answer

Heater hose between rear of intake manifold & heater core. Where it attaches to the intake manifold it appears to be some sort of slip connector...something like an air hose? How do you disconnect...


The plastic clip must be pushed together and pulled. These are very easy to break, Also fitting that goes into manifold will sometimes break off. Use care

Mar 14, 2010 | 1989 GMC C2500

Not finding what you are looking for?
2000 Jaguar XK Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...