Question about 1994 Ford Ranger Supercab

Open Question

1994 Ford ranger do I have to pull the front diff to change seals on the axles driver side

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: front axle how to remove half shaft

Hi.. The step to remove the front Axles of you Vitara.
Raise and support Vehicle . Remove front wheel,
Drain Diff,fluid,
Remove Locking Hub if is equipaded,
Remove Circle clip from axle shaft
On right side of Vehicle, Remove the Stabilizer Little ball joint nut. Remove castle nut Front Tie rod end,
Remove mounting bolts from brake calipper,
Remove Calipper from steering knuckle and wire a side.
Remove Stud Nut from steering knuckle,
Support Lower suspension arm with a jack,
Remove lower strut bracket bolt ,
Lower jack and disconnect Knuckle from lower suspension crontrol arm,
Pull Outler joint from Hub.
Use Large screwdriver or Prybar To pry Right inner joint from differential, The axle will go out making a little froce with the prybar,
To remove the left side,
Remove mounting bolt from inner joint flange,
Pull out axle from hub.

To reinstall just reverse the prosses.

I hope this help on your job...
Thank you for use fixya....


Posted on Aug 19, 2008

Ad
BigBlue77
  • 59 Answers

SOURCE: 2005 Yukon Front Diff Axle seals

You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Posted on Sep 06, 2008

warlock61
  • 659 Answers

SOURCE: rear axle seal replacement 1994 ford bronco

It is fairly easy to do. remove rear wheels and brake drums, remove the differential cover, rotate the diff to access the diff pin bolt and remove, remove pin, push axles inward and remove c clips, slide out axles and replace seals. reverse procedure

Posted on Dec 29, 2008

  • 33 Answers

SOURCE: 1994 toyota 4runner front diff.seal replacement on passenger side

it should be the exact same process just with a little longer axel shaft

Posted on Jan 11, 2009

  • 6982 Answers

SOURCE: 1994 c1500 4x4 front differential left side axle seal replacement

Diff does not need to be removed to change axle. If you are good at this stuff, you can figure your way through it, or get a manual as a guide (haynes etc. are OK for this stuff) Axle is held into carrier by a "c" clip so you do need to remove the cover and spider gears to get it out (not difficult) If you run into a problem, someone here will surely help!

Posted on Apr 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 f150 front axle to diff. seal replacement


OK, you must remove the front axle assembly to access the axle flange and then the seal, follow the instructions at the link but once the axle is out remove the axle flange from the front diff and replace the axle seal, use a seal driver and lube the new seal with lithium grease (white grease). You will need an air impact to get the flange nut off, replace it with a new one (do not reuse) and do not over tighten it. Cinch it down and then go about 1/8 more of full nut rotation to preload carrier bearing setting then spike in place. Ford F150 Front Axle Replacement Part 1

May 19, 2016 | Ford F-150 Cars & Trucks

1 Answer

How to remove the axel shafts from the Diff. 94 ford expl.


Do one side at a time, Jack the front wheel off the ground and remove. Remove the Brake Caliper and Rotor. Remove the large center nut in the Hub. Now remove the two bolts holding the lower part of the strut to the A-Arm and separate. You should be able to pull the hub down far enough to get the end of the axle out with some wiggling and possibly swearing, it not you can remove the lower A-Arm and just pull it off. PLACE A DRIP PAN UNDER THE SPOT WHERE THE AXLE GOES INTO THE TRANSMISSION BEFORE PULLING THE AXLE! Replace the axle to trany input seal and reverse order my instructions. Repeat for other side. This is a good time to replace Brake Pads and Rotors as well.

Apr 02, 2014 | 1988 Ford Ranger

2 Answers

Front end grinding


The end of the drive axle that goes into the diff is in splined into the side gear of the diff and will be dry as there would be no way to stop the oil coming out of the diff past the splines. The diff seal runs on the outside of the side gear and seals the oil in the diff. The drive axle slides in and out of the splined section to compensate for the changing lengths of the axle on turns. Grease on the splines would be a big help as it would allow the splines to move when under drive load.. Check the hub bearings for condition and adjustment and check the hub itself for wear indicators.

Dec 14, 2013 | 1994 Jeep Grand Cherokee

1 Answer

How do i replace the front axle seal drivers side n a 2004 escalade


remove axle nut, remove lower ball joint nut, pop drive shaft loose with punch or wood dowel , pop lower ball join from knuckle pull up push axle out of knuckle , pull back knuckle and tie in place pop out axle with big screwdriver or pry bar ,remove seal replace.

Aug 01, 2012 | 2004 Cadillac Escalade

1 Answer

How do you remove rear axle from 1995 ford ranger 2 wheel drive need to replace oil seal


Raise the vehicle and properly support it. Remove the wheel and drum. Remove the rear diff cover, have a drain pan underneath to catch the gear oil. Place the trans in nuetral, chalk the front wheels to keep vehicle from moving if you forget to put it back into park befor you lower the vehicle. Rotat the differential until you see the bolt that holds the diff pin in place. Remove the bolt, 5/16 or 8 mm I believe. You can then remove the diff pin, do not rotate the diff with the diff pin removed! Push the axle in, you can then remove the C-clip that holds the axle to the side gear, it will usuall drop or just fall out. Pull the axle out of the rear diff and replace the seal. Put everything back together. Use black or grey RTV to reseal the diff cover making sure o clean up both surfaces as best you can. Put trans in park. Lower the vehicle. Remove the fill plug from the side of the differential and fill with gear lube until lube comes out the hole. Reinstall the plug and your good to go. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Mar 15, 2012 | 1995 Ford Ranger Supercab

1 Answer

Rear axle seal replacement 1994 ford bronco


It is fairly easy to do. remove rear wheels and brake drums, remove the differential cover, rotate the diff to access the diff pin bolt and remove, remove pin, push axles inward and remove c clips, slide out axles and replace seals. reverse procedure

Dec 29, 2008 | 1994 Ford Bronco

1 Answer

2005 Yukon Front Diff Axle seals


You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Sep 01, 2008 | 2003 GMC Yukon

1 Answer

1988 Ford Ranger


Well the passenger side axle just slides right out when pulled on. But the drivers side(the shorter axle of the two) has a clip inside the diff that you have to take out in order to get the axle out. Pulling the diff out is very easy, disconnect the front driveshaft and there is a bolt on the left side of the diff you have to take out and then the front cover bolts.
hope that helps

Aug 11, 2008 | 1988 Ford Ranger

1 Answer

How does the axle come out the differencial in the front of a 1988 Ford Ranger 4WD?


for the right side axle- unbolt the diff and drop the axle down with it then take C clip out of the diff.
the left side axle pops out

U joint axles

Aug 11, 2008 | Ford Ranger Cars & Trucks

Not finding what you are looking for?
1994 Ford Ranger Supercab Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...