Question about 1989 Toyota Camry

Open Question

How to remove and replace a power steering pump on a 1989 camry?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 1992 toyota camry tight steering

yes , i am sure you checked for leaks on the rack at the boots on both ends near the wheels. if none try adding a power steering conditioner to the pump . drain the fliud from the reservoir first by taking off one of the hoses the more conditioner the better. this may not work but it is an easy and cheap way first. there is also a relief valve in many pumps that might be stuck not allowing pressure to build.

Posted on May 31, 2008

  • 341 Answers

SOURCE: Power Steering Pump removal

you havr the whole bracket with pump .next you will need PS pulley removal tool take out 3 bolts same tool needed to replace pulley

Posted on Oct 20, 2008

taztheman042
  • 19 Answers

SOURCE: power steering rack 1998 toyota camry

replacing a steering rack is never easy unless you have done it multiple times and will always be diff. from any vehicle

Posted on Jan 25, 2009

davesmith_37
  • 94 Answers

SOURCE: removing power steering pump

To replace the power steering pump, proceed as follows:

  1. Disconnect the power steering return hose from the remote reservoir or pump. Allow the fluid to drain from this hose into a drain pan. Discard the used fluid.
  2. Loosen the bracket or belt tension adjusting bolt, and the pump mounting bolt.
  3. Loosen the belt tension until the belt can be removed. On some cars, it is necessary to lift the vehicle on a hoist and gain access to the power steering pump from underneath the vehicle.
  4. Remove the hoses from the pump, and cap the pump fittings and hoses.
  5. Remove the belt tension adjusting bolt and the mounting bolt, and remove the pump.
  6. Check the pump mounting bolts and bolt holes for wear. Worn bolts must be replaced. If the bolt mounting holes in the pump are worn, pump replacement is necessary.
  7. Reverse steps 1 through 5 to install the power steering pump. Tighten the belt as described previously, and tighten the pump mounting and bracket bolts to the manufacturer's specifications. If o-rings are used on the pressure hose, replace the o-rings. Be sure the hoses are not contacting the exhaust manifold, catalytic converter, or exhaust pipe during or after pump replacement.
  8. Fill the pump reservoir with the manufacturer's recommended power steering fluid, and bleed air from the power steering system as described earlier.

Posted on Feb 27, 2009

  • 449 Answers

SOURCE: steering wheel hard to turn on my 1989 toyota camry

check power steering pump fluid level and belt.

Posted on Mar 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do u bleed a power steering on 89 camry


It's pretty much self bleeding, With the cap off the power steering reservoir turn the wheel as far as it will go one way then turn fully the other way, keep going back and forward until the bubbles stop coming up and it becomes quiet. Sometimes you need to add power steering additive to completely remove the air bubbles.

Mar 10, 2012 | 1989 Toyota Camry

1 Answer

The boot on my left hand side of the power steering rack had ripped how do i get the steering rack of the 1989 toyota camry


are you talking about the drivers side trans-axle? if you are then it is the CV boot that is ripped, it is easier to replace the axle. Loosen lug nuts, jack car up, place on jack stands, remove tire, remove and suspend brake caliper, remove rotor, I believe it is like a 1 inch and 1/4 socket to remove the wheel bearing nut, the CV joint can be pushed through and then removed. Hope this helped

Sep 23, 2010 | 1989 Toyota Camry

1 Answer

Need to change power steering hose


it is a big job since you need ro crimp the hoses properly. I would recommend to send this to a specialist since improper fittings would mean leakage or contamination of the fluids which may lead to loss of pressure, damage or accidents.

Jul 16, 2010 | 1989 Toyota Camry

1 Answer

How do I fix my power steering on my 1989 toyota camry


Bring this to a shop and have them pressure test the pump and rack. Unless the pump is leaking or making a lot of noise don't replace it. This could be the rack and now you spent money on a pump for no reason. have it checked out. I would give you the procrdure but its dangerous and you have to buy the tester which is not cheap.

May 03, 2010 | 1989 Toyota Camry

2 Answers

I have a 1997 toyota camry that was reported to have a power steering hose leak at 125,000 K and when I took it to another mechanic at 127,000 K he told me that I need a new power steering pump and power...


POWER STEERING PUMP OR HOSE HAS NO SET TIME OR MILEAGE TO FAIL WHEN THEY WEAR OUT THEY WILL FAIL ANY TIME.I WOULD HAVE POWER STEERING HOSE REPLACE FIRST.IF YOUR STEERING WAS NORMALWORKING GOOD BEFORE HOSE RUPTURE NO NOISES OR HARD STEERING.REPLACE POWER STEERING HOSE.BECAUSE POWER STEERING PUMP AND RACK PINION UNIT GOING TO COST RIGHT MUCH.ALSO BY IT BEING A IMPORT.

Feb 15, 2010 | 1997 Toyota Camry

1 Answer

Steering wheel hard to turn on my 1989 toyota camry


power steering belt broken or fell off, or the pump is out of oil. The pump is down on the right hand side (passenger) between the fire wall and the engine. You should be able to see if the belt is still on. Check the resevoir for oil. It is on the same side. It's a little plastic pot with a dipstick. Let me know how you make out.

Mar 03, 2009 | 1989 Toyota Camry

1 Answer

Steering wheel hard to turn on my 1989 toyota camry


check power steering pump fluid level and belt.

Mar 03, 2009 | 1989 Toyota Camry

1 Answer

Steering wheel hard to turn


Either the power steering pump is going bad, or the rack and pinion is going bad.

Mar 03, 2009 | 2003 BMW 325

1 Answer

Alternator belt replacement of 1989 Toyota pickup truck . there are 2 belts to get past before we can replace the alternator belt. How is best to remove first two belts.


Start with the power steering belt it takes a 12 mm socket for the bolt in the power steering . also loosen the bolt on the power steering pump pulley. remove the radiator lower fan shroud. It just clips in. pull the power steering belt around the fan and out of the engine compartment then do the a/c belt. That is the best way I know how.

Mar 02, 2009 | 1989 Toyota Pickup SR5

Not finding what you are looking for?
1989 Toyota Camry Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...