Question about 2009 Chrysler Town and Country

Open Question

My Chrysler 2002 town and country has no reverse

My Chrysler 2002 town and country will not operate in to reverse or neutral. I cna shift through all the gears. It is like the emergency brake is on which it isn't. It will move in drive.

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 1263 Answers

SOURCE: radiator fan relay,2001 chrysler town country

the relay is located in the power distribution box under the hood the relay will be a square black or gray cube just pull out and make sure you rerplace it with the same type relay. refer to your owners manual for any questions regarding the fuses and relays

Posted on May 08, 2009

  • 1 Answer

SOURCE: country speedometer doesn't work and won't shift out of 1st gear

transmission speed sensor needs replacing about 40.oo$ at the dealer sits on the right side of transmission looking from the front of the radiator g s.

Posted on Jun 07, 2009

  • 22 Answers

SOURCE: 2002 Chrysler Town & Country starting intermittent

I assume you've checked all connections from the battery and starter to make sure they are clean and tight. It is a little weird that you do not have trouble starting in neutral yet you get a clicking sound in park. My first thought would be the neutral safety switch on the transmission but you shouldn't even get a click in park if that is bad.

One possibility is the contacts in your starter have worn down and are causing too more resistance (explains the clicking). At the back of your starter is a metal cover that is held on by three tiny bolts (6mm). Disconnect the battery first! (You might have to remove the starter to get to this part) Remove this cover and pull out the plunger assembly. Underneath are two brass plates. Compare one plate to the other. If one is noticeably thinner then it could be the cause of the clicking. You will even see a round groove in the plate. You can buy the plunger and contacts from this website: or you can opt to get a starter from your friendly auto parts store. The first picture shows the bad contact on the left. Notice the groove, the metal has become really thin there. 1e874da.jpgThis picture shows a pitted plunger assembly. Always good to replace it too.cd09a24.jpgThis picture shows all the new parts installed.207ff4f.jpg

Posted on Aug 20, 2009

  • 5 Answers

SOURCE: chrysler town and country wiring diagram

Where is the amplifier located on a 2002 Town & Country? My stereo seems to be working, but there is no sound coming out of the speakers.

Posted on Dec 18, 2009

  • 617 Answers

SOURCE: my 2002 chrysler town and country is displaying

The 1684 is about the battery supply to the transmission contol module having been lost sometime in the recent past. It could be an actual disconnect of the battery occured, or through some testing that happened, or a loose wire but in any case I doubt it would affect the engine running.
On the 1297, that one is very specifically pointing to the manifold absolute pressure sensor which is mounted directly to the intake manifold. It has several possible causes:
the 5V supply to the sensor may be open or grounded and that can be verified by reading the voltage on the violet/white wire with the ignition switch in the run position. The signal wire can be open or shorted to ground and that could be checked by measuring between the plug to the module (dark green/red wire) and pin 36 of the plug to the engine controller. The sensor could be loose in its mounting position.
But most likely the sensor itself is faulty and it is easy to replace (a couple of screws). It should cost less than $100 for the part itself.
I would therefor tell the mechanic to examine this MAP sensor and verify what is the status of this sensor and its circuit before doing anything else. I can't give you any opinion about the noises but if the MAP sensor signal is lost then the fuel/air mixture will be imperfect which will often cause not only rough idling but even refusal to start.
Don't authorize opening the engine until you are satisfied that the MAP code has been solved by erasing it and trying to restart the engine and having ir no longer appear. That is the first order of business.

Posted on Feb 17, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

2009 Chrysler T&C makes clicking sound but won't start

you dealer is not going to want to hear this,have them replace the starter,inside the starter are copper contacts it sounds like a bad adjustment on these contacts inside the starter.Just because it's new dosen't mean it can't be bad!

Jul 23, 2009 | 2002 Chrysler Town & Country

1 Answer

1998 Chrysler town and country wont shift into drive

Is the check engine light on ?
You may have a problem with a solenoid or pressure problem in the transaxle.

Jul 31, 2012 | 1998 Chrysler Town & Country

1 Answer

2001 town and country engine light on will not go into drive or reverse plenty of fluid

Does it feel like its even shifting when you move the shifter,Check under hood to see if the shift cable broke or came out of its retainer.

Jan 13, 2012 | 2001 Chrysler Town & Country

1 Answer

Where is the Neutral Safety Switch located on a 2002 Chrysler Town & Country Van?

is the neutral safety switch locatedn on the same place as on a 2006,vs 2002

Oct 29, 2010 | 1992 Chrysler Town & Country

1 Answer

A loud noise when I turn on the AC and shift it to D or R.

What kind of noise? If it's like a squeal it is a lose belt. If it's more like a clunk it's the transmission shifting and you just happen to notice it more because of the higher RPM the motor is at with the AC on. Try getting the vehicle moving with out the AC on then turning it on after you are moving to see if you get the same sound. If it's a squeal you have a loose belt that needs replacement or tightening.

Jul 11, 2010 | 2002 Chrysler Town & Country

1 Answer

On a 2001 Chrysler town and country the transmission will go in park, neutral, reverse and will drive in either drive, 3d or 1st gear. The problem is that it won't shift from 1st gear to second or third...

sounds like you are looking at a rebuild. chrysler transmissions need to be adjusted periodically by a qualified tech. if they aren't adjusted properly the results can be catastrophic.

Dec 18, 2009 | 2008 Chrysler Town & Country

1 Answer

Suspected "neutral switch" malfunction. Turn the key to start, nothing happens. Wiggle the gear shift lever or put it into the neutral position and the car starts normally. Battery in good condition. Is...

Yes there is a part called a "Nuetral safety switch" and here is the part number, I am assuming you have a 3.8 liter V6.

w/ A.T. $23.79 Source:


Oct 30, 2009 | 2002 Chrysler Town & Country

1 Answer

Describe your 2002 Chrysler Town &

Safety neutral switch o.k.? Tried moving shifter through all gears while holding key in start position?

Aug 03, 2009 | 2002 Chrysler Town & Country

1 Answer

Shifts into gear roughly

the pin in the differential inside the trans probably came out. you need a new transmission since this usually causes major case damage.

May 27, 2008 | 1998 Chrysler Town & Country

Not finding what you are looking for?
2009 Chrysler Town and Country Logo

Related Topics:

530 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides